component

DS40MB200SQ

Public Made by Adom

by adom

Texas Instruments Signal Buffers, Repeaters, Splitters, WQFN-48-EP(7x7). Pinout extracted from the datasheet, KiCad symbol/footprint/3D.

componentinterfaceds40mb200sq
Overview Files Discover Packages Releases Dependencies Issues Breadcrumbs Pull Requests Activity

3D Model

Open in new tab ↗
Loads on click. Unloads only if this page sits in the background.

Symbol & Footprint

Schematic Symbol

Open full view ↗
Loads on click. Unloads only if this page sits in the background.

PCB Footprint

Open full view ↗
Loads on click. Unloads only if this page sits in the background.

Datasheet

Open in new tab ↗
Loads on click. Unloads only if this page sits in the background.
Download PDF
Contents

README

markdown

DS40MB200SQ

Texas Instruments · Signal Buffers, Repeaters, Splitters · WQFN-48-EP(7x7)

DS40MB200SQ from Texas Instruments, in a WQFN-48-EP(7x7). Pinout and pin descriptions extracted from the manufacturer datasheet by ds2sf; symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 PREL_1 input 3.3V LVCMOS pre-emphasis level select bit 1 for line-side drivers (LO_0+/- and LO_1+/-). Internally pulled up. Combined with PREL_0 to choose one of four pre-emphasis levels (see PRE_L emphasis table).
2 VCC power_in 3.3V +/-5% supply. Each VCC pin should connect to the VCC plane through a low-inductance via close to the pin; TI recommends a 0.01uF and 0.1uF X7R 0402 bypass capacitor between each VCC pin and ground.
3 SOB_0- output Switch-side B multiplexer 0 inverting CML differential output. Has an internal 50 ohm resistor to VCC. Must be AC-coupled.
4 SOB_0+ output Switch-side B multiplexer 0 non-inverting CML differential output. Has an internal 50 ohm resistor to VCC. Must be AC-coupled.
5 GND power_in Reference ground. Each GND pin must connect to the ground plane through a low-inductance path (typically a via near the pin).
6 LI_0+ input Line-side port 0 non-inverting CML differential input. Has an internal 50 ohm resistor to an internal reference voltage. Must be AC-coupled (see Figure 7-1).
7 LI_0- input Line-side port 0 inverting CML differential input. Has an internal 50 ohm resistor to an internal reference voltage. Must be AC-coupled.
8 VCC power_in 3.3V +/-5% supply. Bypass to ground with 0.01uF and 0.1uF X7R 0402 capacitors close to the pin.
9 LO_1+ output Line-side port 1 non-inverting CML differential output. Has an internal 50 ohm resistor to VCC. Must be AC-coupled.
10 LO_1- output Line-side port 1 inverting CML differential output. Has an internal 50 ohm resistor to VCC. Must be AC-coupled.
11 GND power_in Reference ground. Low-inductance via to the ground plane recommended.
12 PREL_0 input 3.3V LVCMOS pre-emphasis level select bit 0 for line-side drivers (LO_0+/- and LO_1+/-). Internally pulled up. Combined with PREL_1 to select one of four pre-emphasis levels.
13 MUX_S1 input 3.3V LVCMOS multiplexer 1 select: logic high selects switch B for MUX 1. Internally pulled up. Default state of MUX 1 is switch A.
14 VCC power_in 3.3V +/-5% supply. Bypass with 0.01uF and 0.1uF X7R 0402 close to the pin.
15 SIA_1- input Switch-side A multiplexer 1 inverting CML differential input. Has an internal 50 ohm resistor to an internal reference voltage. Must be AC-coupled.
16 SIA_1+ input Switch-side A multiplexer 1 non-inverting CML differential input. Has an internal 50 ohm resistor to an internal reference voltage. Must be AC-coupled.
17 GND power_in Reference ground. Low-inductance via to the ground plane recommended.
18 SIB_1- input Switch-side B multiplexer 1 inverting CML differential input. Has an internal 50 ohm resistor to an internal reference voltage. Must be AC-coupled.
19 SIB_1+ input Switch-side B multiplexer 1 non-inverting CML differential input. Has an internal 50 ohm resistor to an internal reference voltage. Must be AC-coupled.
20 VCC power_in 3.3V +/-5% supply. Bypass with 0.01uF and 0.1uF X7R 0402 close to the pin.
21 SOA_1- output Switch-side A multiplexer 1 inverting CML differential output. Has an internal 50 ohm resistor to VCC.
22 SOA_1+ output Switch-side A multiplexer 1 non-inverting CML differential output. Has an internal 50 ohm resistor to VCC.
23 LB1A input 3.3V LVCMOS. A logic low at LB1A enables the internal loopback path from SIA_1+/- back to SOA_1+/-. Internally pulled up.
24 LB1B input 3.3V LVCMOS. A logic low at LB1B enables the internal loopback path from SIB_1+/- back to SOA_1+/-. Internally pulled up.
25 PRES_1 input 3.3V LVCMOS pre-emphasis level select bit 1 for switch-side drivers (SOA_0+/-, SOB_0+/-, SOA_1+/-, SOB_1+/-). Internally pulled up. Combined with PRES_0 to choose one of four pre-emphasis levels.
26 RSV input Reserved pin used for factory test. May be left open, connected to GND, or tied to GND through an external pull-down resistor.
27 SOB_1- output Switch-side B multiplexer 1 inverting CML differential output. Has an internal 50 ohm resistor to VCC.
28 SOB_1+ output Switch-side B multiplexer 1 non-inverting CML differential output. Has an internal 50 ohm resistor to VCC.
29 VCC power_in 3.3V +/-5% supply. Bypass with 0.01uF and 0.1uF X7R 0402 close to the pin.
30 LI_1+ input Line-side port 1 non-inverting CML differential input. Has an internal 50 ohm resistor to an internal reference voltage. Must be AC-coupled.
31 LI_1- input Line-side port 1 inverting CML differential input. Has an internal 50 ohm resistor to an internal reference voltage. Must be AC-coupled.
32 GND power_in Reference ground. Low-inductance via to the ground plane recommended.
33 LO_0+ output Line-side port 0 non-inverting CML differential output. Has an internal 50 ohm resistor to VCC. Must be AC-coupled.
34 LO_0- output Line-side port 0 inverting CML differential output. Has an internal 50 ohm resistor to VCC. Must be AC-coupled.
35 VCC power_in 3.3V +/-5% supply. Bypass with 0.01uF and 0.1uF X7R 0402 close to the pin.
36 PRES_0 input 3.3V LVCMOS pre-emphasis level select bit 0 for switch-side drivers (SOA_0+/-, SOB_0+/-, SOA_1+/-, SOB_1+/-). Internally pulled up. Combined with PRES_1 to select one of four pre-emphasis levels.
37 MUX_S0 input 3.3V LVCMOS multiplexer 0 select: logic high selects switch B for MUX 0. Internally pulled up. Default state of MUX 0 is switch A.
38 VCC power_in 3.3V +/-5% supply. Bypass with 0.01uF and 0.1uF X7R 0402 close to the pin.
39 SIA_0- input Switch-side A multiplexer 0 inverting CML differential input. Has an internal 50 ohm resistor to an internal reference voltage. Must be AC-coupled.
40 SIA_0+ input Switch-side A multiplexer 0 non-inverting CML differential input. Has an internal 50 ohm resistor to an internal reference voltage. Must be AC-coupled.
41 GND power_in Reference ground. Low-inductance via to the ground plane recommended.
42 SIB_0- input Switch-side B multiplexer 0 inverting CML differential input. Has an internal 50 ohm resistor to an internal reference voltage. Must be AC-coupled.
43 SIB_0+ input Switch-side B multiplexer 0 non-inverting CML differential input. Has an internal 50 ohm resistor to an internal reference voltage. Must be AC-coupled.
44 VCC power_in 3.3V +/-5% supply. Bypass with 0.01uF and 0.1uF X7R 0402 close to the pin.
45 SOA_0- output Switch-side A multiplexer 0 inverting CML differential output. Has an internal 50 ohm resistor to VCC.
46 SOA_0+ output Switch-side A multiplexer 0 non-inverting CML differential output. Has an internal 50 ohm resistor to VCC.
47 LB0A input 3.3V LVCMOS. A logic low at LB0A enables the internal loopback path from SIA_0+/- back to SOA_0+/-. Internally pulled up.
48 LB0B input 3.3V LVCMOS. A logic low at LB0B enables the internal loopback path from SIB_0+/- back to SOA_0+/-. Internally pulled up.
DAP GND power_in Die attach pad (exposed metal pad on the bottom, center of WQFN-48). Must be connected to the GND plane through at least four vias to lower ground impedance and improve thermal performance.

Key specifications

Parameter Value
Manufacturer Texas Instruments
Package WQFN-48-EP(7x7)
Category Interface
Pins 49

Ordering variants

Same part, different packaging or reel option.

  • DS40MB200SQ
  • DS40MB200SQE
  • DS40MB200SQX

CAD (KiCad official)

  • Symbol: DS40MB200SQ
  • Footprint: Package_DFN_QFN:QFN-48-1EP_7x7mm_P0.5mm_EP5.15x5.15mm
  • 3D model: WQFN-48-EP(7x7) (KiCad packages3D, STEP)
  • 3D model files: ds40mb200sq-etched.step / ds40mb200sq-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); ds40mb200sq.step / ds40mb200sq.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: Texas Instruments datasheet (25 pp, sha256 a347064cd35ec67a, retrieved 2026-08-17, tier: lcsc)
  • Datasheet language: Chinese. Pin names, descriptions, and specs on this page were extracted and translated to English by ds2sf; the linked PDF is the manufacturer original.
  • Extractor: ds2sf (Claude). Every pin and dimension is cited to a datasheet page; it refuses to fabricate.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF