← Commit history

Initial commit: component/drv411airgpr

Ray ·aea7ba15dd ·
2 files changed +279
README.mdadded+58
@@ -0,0 +1,58 @@+# DRV411AIRGPR++**Texas Instruments** · ADCs/DACs - Special Purpose · QFN-20(4x4)++DRV411AIRGPR from Texas Instruments, in a QFN-20(4x4). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.++## Pinout++| Pin | Name | Type | Function |+|---|---|---|---|+| 1 | OR | tri_state | Open-drain output indicating differential amplifier overrange condition when output signal clips; requires external pull-up resistor |+| 2 | REFSEL2 | input | Digital CMOS input for reference voltage selection; used with REFSEL1 to select 2.5V fixed, 1.65V fixed, or 50% VDD ratiometric mode |+| 3 | REFSEL1 | input | Digital CMOS input for reference voltage selection; used with REFSEL2 to select 2.5V fixed, 1.65V fixed, or 50% VDD ratiometric mode |+| 4 | REFOUT | output | Output terminal for selected buffered reference voltage (2.5V, 1.65V, or VDD/2) with load regulation 0.15-0.35 mV/mA and ±5 mA sink/source capability |+| 5 | REFIN | input | Input for zero reference to differential amplifier with 50 kΩ input impedance; normally connect to REFOUT or external reference with optional 4×RSHUNT dummy shunt for CMR |+| 6 | VOUT | output | Output of differential amplifier with 4 V/V gain, 2 MHz bandwidth, 6.5 V/µs slew rate, output swing 48-85 mV from supply rails at 2.5 mA load |+| 7 | IAIN2 | input | Noninverting input of differential amplifier connected to positive shunt terminal with 20 kΩ typical impedance and -1 V to VDD+1 V common-mode input range |+| 8 | IAIN1 | input | Inverting input of differential amplifier connected to negative shunt terminal with 20 kΩ typical impedance and -1 V to VDD+1 V common-mode input range |+| 9 | GND | power_in | Ground connection; connect both GND pins to local ground plane for low impedance |+| 10 | GND | power_in | Ground connection; connect both GND pins to local ground plane for low impedance |+| 11 | ICOMP2 | output | Compensation coil H-bridge driver output with peak current 210 mA at 5 V or 125 mA at 3.3 V and common-mode output at VDD/2 |+| 12 | ICOMP1 | output | Compensation coil H-bridge driver output with peak current 210 mA at 5 V or 125 mA at 3.3 V and common-mode output at VDD/2; add external Schottky diodes for high-current protection |+| 13 | VDD | power_in | Power supply voltage input with operating range 2.7 V to 5.5 V, quiescent current 6 mA at 25°C, power-on reset threshold 2.4 V |+| 14 | GSEL2 | input | Digital CMOS input for Hall amplifier gain and compensation frequency selection; use with GSEL1 to select Gain_1/2/3 modes or external op-amp mode |+| 15 | GSEL1 | input | Digital CMOS input for Hall amplifier gain and compensation frequency selection; use with GSEL2 to select Gain_1/2/3 modes or external op-amp mode |+| 16 | ERROR | tri_state | Open-drain output indicating error conditions including power-on reset, brownout >25 µs, Hall sensor offset >50 mV, or open Hall connection; requires external pull-up |+| 17 | HALL4 | input | Connection to pin 4 of symmetrical InSb Hall element (AKM HW322/HW302) for Hall signal output; current limited to 10 mA maximum |+| 18 | HALL3 | output | Connection to pin 3 of symmetrical InSb Hall element (AKM HW322/HW302) for excitation return; provides regulated 0.6-0.95 V across HALL1-HALL3 dependent on GSEL mode |+| 19 | HALL2 | input | Connection to pin 2 of symmetrical InSb Hall element (AKM HW322/HW302) for Hall signal output with dynamic offset and 1/f noise cancellation via current spinning; current limited 10 mA |+| 20 | HALL1 | output | Connection to pin 1 of symmetrical InSb Hall element (AKM HW322/HW302) for excitation drive; provides regulated 0.6-0.95 V across HALL1-HALL3 dependent on GSEL mode |+| 21 | EP | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |++## Key specifications++| Parameter | Value |+|---|---|+| Manufacturer | Texas Instruments |+| Package | QFN-20(4x4) |+| Category | Data Acquisition |+| Pins | 21 |++## CAD (KiCad official)++- Symbol: `DRV411AIRGPR`+- Footprint: `Package_DFN_QFN:QFN-20-1EP_4x4mm_P0.5mm_EP2.5x2.5mm`+- 3D model: QFN-20(4x4) (KiCad packages3D, STEP)+- 3D model files: `drv411airgpr-etched.step` / `drv411airgpr-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `drv411airgpr.step` / `drv411airgpr.glb` are the bare package body.++## Provenance++Data extracted from the manufacturer datasheet, not a distributor listing:++- **Datasheet:** [Texas Instruments datasheet](https://www.ti.com/cn/lit/gpn/drv411) (36 pp, sha256 `2ed3a527ecc9890c`, retrieved 2026-09-24, tier: lcsc)+- **Datasheet language:** Chinese. Pin names, descriptions, and specs on this page were extracted and translated to English by ds2sf; the linked PDF is the manufacturer original.+- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.2`, primary `claude-haiku-4-5-20251001` (text), consensus `claude-sonnet-5` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.+- **CAD:** KiCad official libraries (CC-BY-SA 4.0).++[Datasheet PDF](docs/drv411airgpr-datasheet.pdf)
page.jsonadded+221
@@ -0,0 +1,221 @@+{+  "slug": "drv411airgpr",+  "version": "0.1.0",+  "type": "component",+  "description": "Texas Instruments ADCs/DACs - Special Purpose, QFN-20(4x4). Pinout cross-checked by two models against the datasheet, KiCad symbol/footprint/3D.",+  "tags": [+    "component",+    "data acquisition",+    "drv411airgpr",+    "factory-2.0.0",+    "extractor-text"+  ],+  "dependencies": {},+  "hero": {+    "type": "image",+    "path": "docs/hero.png"+  },+  "files": [+    "page.json",+    "README.md",+    "drv411airgpr.kicad_sym",+    "drv411airgpr.kicad_mod",+    "drv411airgpr.glb",+    "drv411airgpr.step",+    "drv411airgpr.lbr",+    "docs/hero.png",+    "docs/drv411airgpr-datasheet.pdf",+    "viewers/symbol.html",+    "viewers/footprint.html"+  ],+  "component": {+    "mpn": "DRV411AIRGPR",+    "manufacturer": "Texas Instruments",+    "package": "QFN-20(4x4)",+    "pin_count": 21,+    "category": "Data Acquisition",+    "subcategory": "ADCs/DACs - Special Purpose",+    "datasheet": "https://www.ti.com/cn/lit/gpn/drv411",+    "parts": {+      "symbol": "drv411airgpr.kicad_sym",+      "footprint": "drv411airgpr.kicad_mod",+      "model_3d": "drv411airgpr-etched.glb",+      "model_3d_plain": "drv411airgpr.glb",+      "model_3d_step": "drv411airgpr-etched.step",+      "model_3d_step_plain": "drv411airgpr.step",+      "lbr": "drv411airgpr.lbr"+    },+    "distributor_links": {+      "lcsc": "C543037"+    },+    "pins": [+      {+        "number": "1",+        "name": "OR",+        "type": "tri_state",+        "description": "Open-drain output indicating differential amplifier overrange condition when output signal clips; requires external pull-up resistor"+      },+      {+        "number": "2",+        "name": "REFSEL2",+        "type": "input",+        "description": "Digital CMOS input for reference voltage selection; used with REFSEL1 to select 2.5V fixed, 1.65V fixed, or 50% VDD ratiometric mode"+      },+      {+        "number": "3",+        "name": "REFSEL1",+        "type": "input",+        "description": "Digital CMOS input for reference voltage selection; used with REFSEL2 to select 2.5V fixed, 1.65V fixed, or 50% VDD ratiometric mode"+      },+      {+        "number": "4",+        "name": "REFOUT",+        "type": "output",+        "description": "Output terminal for selected buffered reference voltage (2.5V, 1.65V, or VDD/2) with load regulation 0.15-0.35 mV/mA and ±5 mA sink/source capability"+      },+      {+        "number": "5",+        "name": "REFIN",+        "type": "input",+        "description": "Input for zero reference to differential amplifier with 50 kΩ input impedance; normally connect to REFOUT or external reference with optional 4×RSHUNT dummy shunt for CMR"+      },+      {+        "number": "6",+        "name": "VOUT",+        "type": "output",+        "description": "Output of differential amplifier with 4 V/V gain, 2 MHz bandwidth, 6.5 V/µs slew rate, output swing 48-85 mV from supply rails at 2.5 mA load"+      },+      {+        "number": "7",+        "name": "IAIN2",+        "type": "input",+        "description": "Noninverting input of differential amplifier connected to positive shunt terminal with 20 kΩ typical impedance and -1 V to VDD+1 V common-mode input range"+      },+      {+        "number": "8",+        "name": "IAIN1",+        "type": "input",+        "description": "Inverting input of differential amplifier connected to negative shunt terminal with 20 kΩ typical impedance and -1 V to VDD+1 V common-mode input range"+      },+      {+        "number": "9",+        "name": "GND",+        "type": "power_in",+        "description": "Ground connection; connect both GND pins to local ground plane for low impedance"+      },+      {+        "number": "10",+        "name": "GND",+        "type": "power_in",+        "description": "Ground connection; connect both GND pins to local ground plane for low impedance"+      },+      {+        "number": "11",+        "name": "ICOMP2",+        "type": "output",+        "description": "Compensation coil H-bridge driver output with peak current 210 mA at 5 V or 125 mA at 3.3 V and common-mode output at VDD/2"+      },+      {+        "number": "12",+        "name": "ICOMP1",+        "type": "output",+        "description": "Compensation coil H-bridge driver output with peak current 210 mA at 5 V or 125 mA at 3.3 V and common-mode output at VDD/2; add external Schottky diodes for high-current protection"+      },+      {+        "number": "13",+        "name": "VDD",+        "type": "power_in",+        "description": "Power supply voltage input with operating range 2.7 V to 5.5 V, quiescent current 6 mA at 25°C, power-on reset threshold 2.4 V"+      },+      {+        "number": "14",+        "name": "GSEL2",+        "type": "input",+        "description": "Digital CMOS input for Hall amplifier gain and compensation frequency selection; use with GSEL1 to select Gain_1/2/3 modes or external op-amp mode"+      },+      {+        "number": "15",+        "name": "GSEL1",+        "type": "input",+        "description": "Digital CMOS input for Hall amplifier gain and compensation frequency selection; use with GSEL2 to select Gain_1/2/3 modes or external op-amp mode"+      },+      {+        "number": "16",+        "name": "ERROR",+        "type": "tri_state",+        "description": "Open-drain output indicating error conditions including power-on reset, brownout >25 µs, Hall sensor offset >50 mV, or open Hall connection; requires external pull-up"+      },+      {+        "number": "17",+        "name": "HALL4",+        "type": "input",+        "description": "Connection to pin 4 of symmetrical InSb Hall element (AKM HW322/HW302) for Hall signal output; current limited to 10 mA maximum"+      },+      {+        "number": "18",+        "name": "HALL3",+        "type": "output",+        "description": "Connection to pin 3 of symmetrical InSb Hall element (AKM HW322/HW302) for excitation return; provides regulated 0.6-0.95 V across HALL1-HALL3 dependent on GSEL mode"+      },+      {+        "number": "19",+        "name": "HALL2",+        "type": "input",+        "description": "Connection to pin 2 of symmetrical InSb Hall element (AKM HW322/HW302) for Hall signal output with dynamic offset and 1/f noise cancellation via current spinning; current limited 10 mA"+      },+      {+        "number": "20",+        "name": "HALL1",+        "type": "output",+        "description": "Connection to pin 1 of symmetrical InSb Hall element (AKM HW322/HW302) for excitation drive; provides regulated 0.6-0.95 V across HALL1-HALL3 dependent on GSEL mode"+      },+      {+        "number": "21",+        "name": "EP",+        "type": "passive",+        "description": "Exposed pad (from the footprint; not named in the datasheet pin table)."+      }+    ],+    "provenance": {+      "extractor": "extract_pins 0.2",+      "factory_chain": {+        "factory": "2.0.0",+        "extractor": "extract_pins 0.2",+        "primary_model": "claude-haiku-4-5-20251001",+        "primary_mode": "text",+        "consensus_model": "claude-sonnet-5",+        "consensus": "agreed",+        "guards": "pin_guards 0.1: passed",+        "guard_notes": [+          "exposed pad 21 added from the footprint"+        ],+        "pages_sent": 36,+        "cost_usd": 0.426,+        "at": "2026-09-24T10:25:26"+      },+      "datasheet": {+        "url": "https://www.ti.com/cn/lit/gpn/drv411",+        "pages": 36,+        "sha256": "2ed3a527ecc9890c",+        "source_tier": "lcsc"+      },+      "cad": "KiCad official (CC-BY-SA 4.0)",+      "pins": {+        "total": 21,+        "described": 21,+        "cites_pages": true,+        "refuses_to_fabricate": true+      }+    },+    "viewers": {+      "symbol": "viewers/symbol.html",+      "footprint": "viewers/footprint.html"+    }+  },+  "visibility": "public",+  "org": "adom",+  "author": {+    "name": "Ray",+    "email": "[email protected]"+  }+}\ No newline at end of file