Loads when you scroll to it. Unloads after 5 minutes in the background.

Symbol & Footprint

Schematic Symbol

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.

PCB Footprint

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Loads when you scroll to it. Unloads after 5 minutes in the background.
Download PDF
Contents

README

markdown

DRV411AIRGPR

Texas Instruments · ADCs/DACs - Special Purpose · QFN-20(4x4)

DRV411AIRGPR from Texas Instruments, in a QFN-20(4x4). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 OR tri_state Open-drain output indicating differential amplifier overrange condition when output signal clips; requires external pull-up resistor
2 REFSEL2 input Digital CMOS input for reference voltage selection; used with REFSEL1 to select 2.5V fixed, 1.65V fixed, or 50% VDD ratiometric mode
3 REFSEL1 input Digital CMOS input for reference voltage selection; used with REFSEL2 to select 2.5V fixed, 1.65V fixed, or 50% VDD ratiometric mode
4 REFOUT output Output terminal for selected buffered reference voltage (2.5V, 1.65V, or VDD/2) with load regulation 0.15-0.35 mV/mA and ±5 mA sink/source capability
5 REFIN input Input for zero reference to differential amplifier with 50 kΩ input impedance; normally connect to REFOUT or external reference with optional 4×RSHUNT dummy shunt for CMR
6 VOUT output Output of differential amplifier with 4 V/V gain, 2 MHz bandwidth, 6.5 V/µs slew rate, output swing 48-85 mV from supply rails at 2.5 mA load
7 IAIN2 input Noninverting input of differential amplifier connected to positive shunt terminal with 20 kΩ typical impedance and -1 V to VDD+1 V common-mode input range
8 IAIN1 input Inverting input of differential amplifier connected to negative shunt terminal with 20 kΩ typical impedance and -1 V to VDD+1 V common-mode input range
9 GND power_in Ground connection; connect both GND pins to local ground plane for low impedance
10 GND power_in Ground connection; connect both GND pins to local ground plane for low impedance
11 ICOMP2 output Compensation coil H-bridge driver output with peak current 210 mA at 5 V or 125 mA at 3.3 V and common-mode output at VDD/2
12 ICOMP1 output Compensation coil H-bridge driver output with peak current 210 mA at 5 V or 125 mA at 3.3 V and common-mode output at VDD/2; add external Schottky diodes for high-current protection
13 VDD power_in Power supply voltage input with operating range 2.7 V to 5.5 V, quiescent current 6 mA at 25°C, power-on reset threshold 2.4 V
14 GSEL2 input Digital CMOS input for Hall amplifier gain and compensation frequency selection; use with GSEL1 to select Gain_1/2/3 modes or external op-amp mode
15 GSEL1 input Digital CMOS input for Hall amplifier gain and compensation frequency selection; use with GSEL2 to select Gain_1/2/3 modes or external op-amp mode
16 ERROR tri_state Open-drain output indicating error conditions including power-on reset, brownout >25 µs, Hall sensor offset >50 mV, or open Hall connection; requires external pull-up
17 HALL4 input Connection to pin 4 of symmetrical InSb Hall element (AKM HW322/HW302) for Hall signal output; current limited to 10 mA maximum
18 HALL3 output Connection to pin 3 of symmetrical InSb Hall element (AKM HW322/HW302) for excitation return; provides regulated 0.6-0.95 V across HALL1-HALL3 dependent on GSEL mode
19 HALL2 input Connection to pin 2 of symmetrical InSb Hall element (AKM HW322/HW302) for Hall signal output with dynamic offset and 1/f noise cancellation via current spinning; current limited 10 mA
20 HALL1 output Connection to pin 1 of symmetrical InSb Hall element (AKM HW322/HW302) for excitation drive; provides regulated 0.6-0.95 V across HALL1-HALL3 dependent on GSEL mode
21 EP passive Exposed pad (from the footprint; not named in the datasheet pin table).

Key specifications

Parameter Value
Manufacturer Texas Instruments
Package QFN-20(4x4)
Category Data Acquisition
Pins 21

CAD (KiCad official)

  • Symbol: DRV411AIRGPR
  • Footprint: Package_DFN_QFN:QFN-20-1EP_4x4mm_P0.5mm_EP2.5x2.5mm
  • 3D model: QFN-20(4x4) (KiCad packages3D, STEP)
  • 3D model files: drv411airgpr-etched.step / drv411airgpr-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); drv411airgpr.step / drv411airgpr.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: Texas Instruments datasheet (36 pp, sha256 2ed3a527ecc9890c, retrieved 2026-09-24, tier: lcsc)
  • Datasheet language: Chinese. Pin names, descriptions, and specs on this page were extracted and translated to English by ds2sf; the linked PDF is the manufacturer original.
  • Extractor: parts-factory 2.0.0 / extract_pins 0.2, primary claude-haiku-4-5-20251001 (text), consensus claude-sonnet-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF