← Commit history

Initial commit: component/drv104pwp

Ray ·e0dc5bb73e ·
2 files changed +251
README.mdadded+51
@@ -0,0 +1,51 @@+# DRV104PWP++**Texas Instruments** · Power Distribution Switches · HTSSOP-14-EP++DRV104PWP from Texas Instruments, in a HTSSOP-14-EP. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.++## Pinout++| Pin | Name | Type | Function |+|---|---|---|---|+| 1 | Duty Cycle Adj | input | Analog input connected to comparator input and 2.75×IREF current source that linearly sets PWM duty cycle; active range 1.3V to 3.9V corresponds to 10% to 90% duty cycle. |+| 2 | Delay Adj | input | Controls duration of initial 100% duty cycle before PWM mode through charge to 2.6V threshold comparator; internally driven by 15µA current source from VS; floating pin limits delay to 18µs minimum. |+| 3 | Osc Freq Adj | input | External resistor to ground sets PWM oscillator frequency from 500Hz to 100kHz by controlling IREF current source; in slave mode sets current limit reset frequency. |+| 4 | Master | input | Logic input that selects master mode (floating/high, pulls to 5V internally via 15µA source) making SYNC an output, or slave mode (low) making SYNC an input. |+| 5 | BOOT | passive | Bootstrap capacitor connection node (>100pF, typically 470pF) between this pin and power output that supplies VGS charge to gate drive the high-side DMOS transistor. |+| 6 | OUT1 | output | High-side power output from DMOS source connected to VPS with low on-resistance (0.45Ω typical), saturation voltage 0.45V to 0.65V at 1A, current-limited to 1.2A typical. |+| 7 | OUT2 | output | High-side power output from DMOS source connected to VPS with low on-resistance (0.45Ω typical), saturation voltage 0.45V to 0.65V at 1A, current-limited to 1.2A typical. |+| 8 | VPS1 | power_in | Load power-supply connection to drain of power DMOS transistor; voltage may exceed VS by 5V maximum but must not exceed 37V practical limit or 40V absolute maximum. |+| 9 | VPS2 | power_in | Load power-supply connection to drain of power DMOS transistor; voltage may exceed VS by 5V maximum but must not exceed 37V practical limit or 40V absolute maximum. |+| 10 | +VS | power_in | Logic and control circuit power supply with operating range 8V to 32V; quiescent current 0.6mA to 1mA at 24V nominal supply. |+| 11 | GND | power_in | Ground reference for all logic and control circuits; does not carry load current when power DMOS device is switched on. |+| 12 | SYNC | bidirectional | Synchronization output in master mode (0V to 4.2V, 100µA source with 1kΩ output resistance) providing copy of power output state; input in slave mode with 2V switching threshold controlling power output. |+| 13 | Status OK Flag | output | Open-drain active-low flag output that indicates over-temperature fault (junction ≥160°C) or over-current condition; requires pull-up resistor and sinks up to 10mA typical. |+| 14 | Input | input | TTL-compatible logic input with 1.8V switching threshold; device enabled when driven above 2.2V, disabled below 1.2V; input current typically 1µA at all logic levels. |+| 15 | EP | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |++## Key specifications++| Parameter | Value |+|---|---|+| Manufacturer | Texas Instruments |+| Package | HTSSOP-14-EP |+| Category | Power Management (PMIC) |+| Pins | 15 |++## CAD (KiCad official)++- Symbol: `DRV104PWP`+- Footprint: `Package_SO:TSSOP-14-1EP_4.4x5mm_P0.65mm`+- 3D model: HTSSOP-14-EP (KiCad packages3D, STEP)+- 3D model files: `drv104pwp-etched.step` / `drv104pwp-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `drv104pwp.step` / `drv104pwp.glb` are the bare package body.++## Provenance++Data extracted from the manufacturer datasheet, not a distributor listing:++- **Datasheet:** [Texas Instruments datasheet](https://www.ti.com/cn/lit/gpn/drv104) (25 pp, sha256 `e259add3a2ce23ae`, retrieved 2026-09-30, tier: lcsc)+- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.3`, primary `claude-haiku-4-5-20251001` (text), consensus `claude-sonnet-5-5` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.+- **CAD:** KiCad official libraries (CC-BY-SA 4.0).++[Datasheet PDF](docs/drv104pwp-datasheet.pdf)
page.jsonadded+200
@@ -0,0 +1,200 @@+{+  "slug": "drv104pwp",+  "version": "0.1.0",+  "type": "component",+  "description": "Texas Instruments Power Distribution Switches, HTSSOP-14-EP. Pinout cross-checked by two models against the datasheet, KiCad symbol/footprint/3D.",+  "tags": [+    "component",+    "power management (pmic)",+    "drv104pwp",+    "factory-2.0.0",+    "extractor-text"+  ],+  "dependencies": {},+  "hero": {+    "type": "image",+    "path": "docs/hero.png"+  },+  "files": [+    "page.json",+    "README.md",+    "drv104pwp.kicad_sym",+    "drv104pwp.kicad_mod",+    "drv104pwp.glb",+    "drv104pwp.step",+    "drv104pwp.lbr",+    "docs/hero.png",+    "docs/drv104pwp-datasheet.pdf",+    "viewers/symbol.html",+    "viewers/footprint.html"+  ],+  "component": {+    "mpn": "DRV104PWP",+    "manufacturer": "Texas Instruments",+    "package": "HTSSOP-14-EP",+    "pin_count": 15,+    "category": "Power Management (PMIC)",+    "subcategory": "Power Distribution Switches",+    "datasheet": "https://www.ti.com/cn/lit/gpn/drv104",+    "parts": {+      "symbol": "drv104pwp.kicad_sym",+      "footprint": "drv104pwp.kicad_mod",+      "model_3d": "drv104pwp-etched.glb",+      "model_3d_plain": "drv104pwp.glb",+      "model_3d_step": "drv104pwp-etched.step",+      "model_3d_step_plain": "drv104pwp.step",+      "lbr": "drv104pwp.lbr"+    },+    "distributor_links": {+      "lcsc": "C1556572",+      "digikey": "296-26053-5-ND",+      "mouser": "595-DRV104PWP"+    },+    "distributor_check": {+      "checked_at": "2026-09-30T01:18:54Z",+      "source": "Component Ocean /api/assign-pns",+      "digikey": {+        "pn": "296-26053-5-ND",+        "status": "found"+      },+      "mouser": {+        "pn": "595-DRV104PWP",+        "status": "found"+      }+    },+    "pins": [+      {+        "number": "1",+        "name": "Duty Cycle Adj",+        "type": "input",+        "description": "Analog input connected to comparator input and 2.75×IREF current source that linearly sets PWM duty cycle; active range 1.3V to 3.9V corresponds to 10% to 90% duty cycle."+      },+      {+        "number": "2",+        "name": "Delay Adj",+        "type": "input",+        "description": "Controls duration of initial 100% duty cycle before PWM mode through charge to 2.6V threshold comparator; internally driven by 15µA current source from VS; floating pin limits delay to 18µs minimum."+      },+      {+        "number": "3",+        "name": "Osc Freq Adj",+        "type": "input",+        "description": "External resistor to ground sets PWM oscillator frequency from 500Hz to 100kHz by controlling IREF current source; in slave mode sets current limit reset frequency."+      },+      {+        "number": "4",+        "name": "Master",+        "type": "input",+        "description": "Logic input that selects master mode (floating/high, pulls to 5V internally via 15µA source) making SYNC an output, or slave mode (low) making SYNC an input."+      },+      {+        "number": "5",+        "name": "BOOT",+        "type": "passive",+        "description": "Bootstrap capacitor connection node (>100pF, typically 470pF) between this pin and power output that supplies VGS charge to gate drive the high-side DMOS transistor."+      },+      {+        "number": "6",+        "name": "OUT1",+        "type": "output",+        "description": "High-side power output from DMOS source connected to VPS with low on-resistance (0.45Ω typical), saturation voltage 0.45V to 0.65V at 1A, current-limited to 1.2A typical."+      },+      {+        "number": "7",+        "name": "OUT2",+        "type": "output",+        "description": "High-side power output from DMOS source connected to VPS with low on-resistance (0.45Ω typical), saturation voltage 0.45V to 0.65V at 1A, current-limited to 1.2A typical."+      },+      {+        "number": "8",+        "name": "VPS1",+        "type": "power_in",+        "description": "Load power-supply connection to drain of power DMOS transistor; voltage may exceed VS by 5V maximum but must not exceed 37V practical limit or 40V absolute maximum."+      },+      {+        "number": "9",+        "name": "VPS2",+        "type": "power_in",+        "description": "Load power-supply connection to drain of power DMOS transistor; voltage may exceed VS by 5V maximum but must not exceed 37V practical limit or 40V absolute maximum."+      },+      {+        "number": "10",+        "name": "+VS",+        "type": "power_in",+        "description": "Logic and control circuit power supply with operating range 8V to 32V; quiescent current 0.6mA to 1mA at 24V nominal supply."+      },+      {+        "number": "11",+        "name": "GND",+        "type": "power_in",+        "description": "Ground reference for all logic and control circuits; does not carry load current when power DMOS device is switched on."+      },+      {+        "number": "12",+        "name": "SYNC",+        "type": "bidirectional",+        "description": "Synchronization output in master mode (0V to 4.2V, 100µA source with 1kΩ output resistance) providing copy of power output state; input in slave mode with 2V switching threshold controlling power output."+      },+      {+        "number": "13",+        "name": "Status OK Flag",+        "type": "output",+        "description": "Open-drain active-low flag output that indicates over-temperature fault (junction ≥160°C) or over-current condition; requires pull-up resistor and sinks up to 10mA typical."+      },+      {+        "number": "14",+        "name": "Input",+        "type": "input",+        "description": "TTL-compatible logic input with 1.8V switching threshold; device enabled when driven above 2.2V, disabled below 1.2V; input current typically 1µA at all logic levels."+      },+      {+        "number": "15",+        "name": "EP",+        "type": "passive",+        "description": "Exposed pad (from the footprint; not named in the datasheet pin table)."+      }+    ],+    "provenance": {+      "extractor": "extract_pins 0.3",+      "factory_chain": {+        "factory": "2.0.0",+        "extractor": "extract_pins 0.3",+        "primary_model": "claude-haiku-4-5-20251001",+        "primary_mode": "text",+        "consensus_model": "claude-sonnet-5-5",+        "consensus": "agreed",+        "guards": "pin_guards 0.1: passed",+        "guard_notes": [+          "extractor flagged: The HTSSOP-14-EP package includes an exposed thermal pad (EP) beneath the die which is not listed in",+          "exposed pad 15 added from the footprint"+        ],+        "pages_sent": 8,+        "cost_usd": 0.1222,+        "at": "2026-09-30T01:18:40"+      },+      "datasheet": {+        "url": "https://www.ti.com/cn/lit/gpn/drv104",+        "pages": 25,+        "sha256": "e259add3a2ce23ae",+        "source_tier": "lcsc"+      },+      "cad": "KiCad official (CC-BY-SA 4.0)",+      "pins": {+        "total": 15,+        "described": 15,+        "cites_pages": true,+        "refuses_to_fabricate": true+      }+    },+    "viewers": {+      "symbol": "viewers/symbol.html",+      "footprint": "viewers/footprint.html"+    }+  },+  "visibility": "public",+  "org": "adom",+  "author": {+    "name": "Ray",+    "email": "[email protected]"+  }+}\ No newline at end of file