component
DRV103H
Public Made by Adomby adom
Texas Instruments Brushed DC Motor Drivers, SOIC-8-EP. Datasheet-verified pinout, KiCad symbol/footprint/3D.
3D Model
Open in new tab ↗
Loads on click. Unloads only if this page sits in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads on click. Unloads only if this page sits in the background.
PCB Footprint
Open full view ↗Loads on click. Unloads only if this page sits in the background.
Datasheet
Open in new tab ↗Loads on click. Unloads only if this page sits in the background.
README
markdownDRV103H
Texas Instruments · Brushed DC Motor Drivers · SOIC-8-EP
DRV103H from Texas Instruments, in a SOIC-8-EP. Pinout and pin descriptions extracted from the manufacturer datasheet by ds2sf; symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | DUTY CYCLE ADJUST | input | Sets PWM duty cycle via a resistor, analog voltage, or D/A converter output over an active range of 1.3V to 3.9V, connecting internally to a comparator input and a 2.75×IREF current source from VS. |
| 2 | DELAY ADJUST | input | Sets the duration of the initial 100% duty-cycle (DC) output before switching to PWM mode via an external capacitor to ground, with the pin left floating giving ~18µs delay or tied to 5V giving <1µs delay, and is compared internally to a 2.6V threshold. |
| 3 | OSC FREQ ADJUST | input | A resistor from this pin to ground sets the internal PWM oscillator frequency, adjustable from 500Hz to 100kHz with practical resistor values. |
| 4 | GND | power_in | System ground return pin that must be connected for the device to function; carries the 0.4mA quiescent current plus the full load current when the output DMOS is on, and is also internally tied to the PowerPAD exposed metal tab (which must not be used as a current-carrying ground). |
| 5 | OUT | output | Drain of the low-side power DMOS output transistor (source grounded) with 0.5Ω typical on-resistance, slew-rate-limited rise/fall times, and rated up to 3A for the PowerPAD SO-8 (H) package; requires an external flyback diode for inductive loads. |
| 6 | +VS | power_in | Power supply input pin with an operating range of +8V to +32V (absolute maximum +40V), which must be greater than or equal to the load supply voltage. |
| 7 | STATUS OK FLAG | output | Active-LOW open-drain fault flag (normally HIGH with external pull-up) that goes LOW (~0.3V) during an over-current or thermal-shutdown fault, capable of sinking up to 10mA typical. |
| 8 | INPUT | input | TTL-compatible digital control input that enables the output when driven above ~1.7V (2.2V to 5.5V = ON) and disables it when below ~1.2V (0V to 1.2V = OFF); must not be tied directly to VS. |
| 9 | EP | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Texas Instruments |
| Package | SOIC-8-EP |
| Category | Motor Driver ICs |
| Pins | 9 |
CAD (KiCad official)
- Symbol:
DRV103H - Footprint:
Package_SO:SOIC-8-1EP_3.9x4.9mm_P1.27mm_EP2.29x3mm - 3D model: SOIC-8-EP (KiCad packages3D, STEP)
- 3D model files:
drv103h-etched.step/drv103h-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);drv103h.step/drv103h.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Texas Instruments datasheet (27 pp, sha256
6449d7cec62e2573, retrieved 2026-09-23, tier: lcsc) - Extractor: parts-factory
2.0.0/extract_pins 0.2, primaryclaude-haiku-4-5-20251001(text), consensusclaude-sonnet-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).