component
D2632-ADJ
Public Made by Adomby adom
Silicore Linear Voltage Regulators (LDO), TO-263-5. Pinout cross-checked by two models against the datasheet, KiCad symbol/footprint/3D.
main
D2632-ADJ
Silicore · Linear Voltage Regulators (LDO) · TO-263-5
D2632-ADJ from Silicore, in a TO-263-5. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | EN | input | Enable pin for ON/OFF control with TTL/CMOS-compatible thresholds (high/ON at 2.4 V min, low/OFF at 0.8 V max), and it may be tied to VIN or to a level up to 30 V when ON/OFF control is not needed. |
| 2 | VIN | power_in | Power supply input with a maximum continuous supply voltage of 26 V; transients up to 50 V are allowed only for under 100 ms at no more than 1% duty cycle, and the absolute rating is -20 V to +50 V. |
| 3 | GND | power_in | Ground reference pin; a 0.1 µF capacitor between VIN and GND is recommended when the input source has high AC impedance. |
| 4 | VOUT | power_out | Regulated output that requires a minimum output capacitor of 10 µF at full load, with a minimum load current of 7 mA to avoid leakage-driven output rise, and it delivers up to 3 A (full load). |
| 5 | ADJ | input | Adjust pin of the adjustable version used with an external two-resistor divider to set VOUT from 1.25 V up to 26 V, with a reference of 1.240 V typ and an adjust-pin bias current of 40 to 120 nA. |
| 6 | EP | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Silicore |
| Package | TO-263-5 |
| Category | Power Supply Chip |
| Pins | 6 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Input Supply Voltage (continuous max 26V; 50V only for <100ms, duty ≤1%) | VIN | -20 | 50 | V | Transient, limited duration (<100msec) and duty cycle (≤1%) for max 50V (*1) | 3 | |
| Lead Temperature (soldering) | TLEAD | 260 | ℃ | Soldering, 5 seconds | 3 | ||
| Operating Junction Temperature | TOPR | -40 | 125 | ℃ | 3 | ||
| Storage Temperature Range | TSTG | -55 | 150 | ℃ | 3 | ||
| Thermal Resistance (junction-to-case) | θJC | 2 | ℃/W | 3 | |||
| Maximum Operating Input Voltage | VIN | 26 | V | 3 | |||
| Adjustable output voltage range (programmable) | 1.25 | 26 | V | Adjustable version, programmed between 1.25V and 26V maximum operating rating | 7 | ||
| Minimum Load Current | 7 | mA | Minimum load current across operating temperature range | 7 | |||
| Minimum output capacitor at full load | 10 | μF | Stability at full load (aluminum electrolytic adequate) | 6 | |||
| Output Voltage tolerance | -1 | 1 | % | IO=10mA | 3 | ||
| Output Voltage tolerance over load and line | -2 | 2 | % | 10mA≤IO≤IFL, (VOUT+1V) ≤VIN≤26V (*2) | 3 | ||
| Line Regulation | 0.06 | 0.5 | % | IO=10mA, (VOUT+1V) ≤VIN≤26V | 3 | ||
| Load Regulation | 0.2 | 1 | % | VIN=VOUT+5V, 10mA≤IOUT≤IFULLLOAD (*2,3) | 3 | ||
| Output Voltage Temperature Coefficient | 20 | 100 | ppm/℃ | 3 | |||
| Reference Voltage | 1.203 | 1.277 | V | VREF ≤ VOUT ≤ (VIN, 1 V), 2.3V ≤ VIN ≤ 26V, 10mA < IL ≤ IFL, TJ ≤ TJ MAX (*7) | 4 | ||
| Reference Voltage Temperature Coefficient | 20 | ppm/℃ | (*8) | 4 | |||
| Adjust Pin Bias Current Temperature Coefficient | 0.1 | nA/℃ | 4 | ||||
| Input Logic Voltage High (ON) | 2.4 | V | 4 | ||||
| Input Logic Voltage Low (OFF) | 0.8 | V | 4 |
CAD (KiCad official)
- Symbol:
D2632-ADJ - Footprint:
Package_TO_SOT_SMD:TO-263-5_TabPin6 - 3D model: TO-263-5 (KiCad packages3D, STEP)
- 3D model files:
d2632-adj-etched.step/d2632-adj-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);d2632-adj.step/d2632-adj.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Silicore datasheet (11 pp, sha256
434713b4bfd480c6, retrieved 2026-10-18, tier: lcsc) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).
# D2632-ADJ
**Silicore** · Linear Voltage Regulators (LDO) · TO-263-5
D2632-ADJ from Silicore, in a TO-263-5. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
## Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | EN | input | Enable pin for ON/OFF control with TTL/CMOS-compatible thresholds (high/ON at 2.4 V min, low/OFF at 0.8 V max), and it may be tied to VIN or to a level up to 30 V when ON/OFF control is not needed. |
| 2 | VIN | power_in | Power supply input with a maximum continuous supply voltage of 26 V; transients up to 50 V are allowed only for under 100 ms at no more than 1% duty cycle, and the absolute rating is -20 V to +50 V. |
| 3 | GND | power_in | Ground reference pin; a 0.1 µF capacitor between VIN and GND is recommended when the input source has high AC impedance. |
| 4 | VOUT | power_out | Regulated output that requires a minimum output capacitor of 10 µF at full load, with a minimum load current of 7 mA to avoid leakage-driven output rise, and it delivers up to 3 A (full load). |
| 5 | ADJ | input | Adjust pin of the adjustable version used with an external two-resistor divider to set VOUT from 1.25 V up to 26 V, with a reference of 1.240 V typ and an adjust-pin bias current of 40 to 120 nA. |
| 6 | EP | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |
## Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Silicore |
| Package | TO-263-5 |
| Category | Power Supply Chip |
| Pins | 6 |
## Electrical characteristics
Limits as printed in the datasheet (page.json `metadata.characteristics` carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Input Supply Voltage (continuous max 26V; 50V only for <100ms, duty ≤1%) | VIN | -20 | | 50 | V | Transient, limited duration (<100msec) and duty cycle (≤1%) for max 50V (*1) | 3 |
| Lead Temperature (soldering) | TLEAD | | | 260 | ℃ | Soldering, 5 seconds | 3 |
| Operating Junction Temperature | TOPR | -40 | | 125 | ℃ | | 3 |
| Storage Temperature Range | TSTG | -55 | | 150 | ℃ | | 3 |
| Thermal Resistance (junction-to-case) | θJC | | 2 | | ℃/W | | 3 |
| Maximum Operating Input Voltage | VIN | | | 26 | V | | 3 |
| Adjustable output voltage range (programmable) | | 1.25 | | 26 | V | Adjustable version, programmed between 1.25V and 26V maximum operating rating | 7 |
| Minimum Load Current | | 7 | | | mA | Minimum load current across operating temperature range | 7 |
| Minimum output capacitor at full load | | 10 | | | μF | Stability at full load (aluminum electrolytic adequate) | 6 |
| Output Voltage tolerance | | -1 | | 1 | % | IO=10mA | 3 |
| Output Voltage tolerance over load and line | | -2 | | 2 | % | 10mA≤IO≤IFL, (VOUT+1V) ≤VIN≤26V (*2) | 3 |
| Line Regulation | | | 0.06 | 0.5 | % | IO=10mA, (VOUT+1V) ≤VIN≤26V | 3 |
| Load Regulation | | | 0.2 | 1 | % | VIN=VOUT+5V, 10mA≤IOUT≤IFULLLOAD (*2,3) | 3 |
| Output Voltage Temperature Coefficient | | | 20 | 100 | ppm/℃ | | 3 |
| Reference Voltage | | 1.203 | | 1.277 | V | VREF ≤ VOUT ≤ (VIN, 1 V), 2.3V ≤ VIN ≤ 26V, 10mA < IL ≤ IFL, TJ ≤ TJ MAX (*7) | 4 |
| Reference Voltage Temperature Coefficient | | | 20 | | ppm/℃ | (*8) | 4 |
| Adjust Pin Bias Current Temperature Coefficient | | | 0.1 | | nA/℃ | | 4 |
| Input Logic Voltage High (ON) | | 2.4 | | | V | | 4 |
| Input Logic Voltage Low (OFF) | | | | 0.8 | V | | 4 |
## CAD (KiCad official)
- Symbol: `D2632-ADJ`
- Footprint: `Package_TO_SOT_SMD:TO-263-5_TabPin6`
- 3D model: TO-263-5 (KiCad packages3D, STEP)
- 3D model files: `d2632-adj-etched.step` / `d2632-adj-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `d2632-adj.step` / `d2632-adj.glb` are the bare package body.
## Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- **Datasheet:** [Silicore datasheet](https://jlcpcb.com/api/file/downloadByFileSystemAccessId/8588943963244417024) (11 pp, sha256 `434713b4bfd480c6`, retrieved 2026-10-18, tier: lcsc)
- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.3`, primary `claude-haiku-5-5` (text), consensus `claude-sonnet-5-5` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
- **CAD:** KiCad official libraries (CC-BY-SA 4.0).
[Datasheet PDF](docs/d2632-adj-datasheet.pdf)