component
D2596HV-ADJ
Public Made by Adomby adom
Silicore DC-DC Converters, TO-263-5. Pinout cross-checked by two models against the datasheet, KiCad symbol/footprint/3D.
main
D2596HV-ADJ
Silicore · DC-DC Converters · TO-263-5
D2596HV-ADJ from Silicore, in a TO-263-5. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | VIN | power_in | Positive input supply for the switching regulator, which needs a suitable input bypass capacitor to minimize voltage transients and supply switching currents, with a recommended supply range of 6 V to 60 V (63 V absolute maximum). |
| 2 | OUTPUT | power_out | Internal switch output that swings between (+VIN − VSAT) and approximately −0.5 V, so the PC board copper connected to it should be kept to a minimum to limit coupling to sensitive circuitry. |
| 3 | GND | power_in | Circuit ground reference for the regulator. |
| 4 | FEEDBACK | input | Senses the regulated output voltage to complete the feedback loop; on the ADJ version it is the programming divider node, with a feedback bias current of 50 nA typical and 100 nA maximum at VOUT = 5 V, and resistors should not exceed 100 kΩ. |
| 5 | ON / OFF | input | Shuts the regulator down with logic levels: leave grounded or drive below 0.8 V (VIL) for normal operation and drive above 2.0 V (VIH) for standby, within a range of −0.3 V to +VIN, and it should not be left open. |
| 6 | EP | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Silicore |
| Package | TO-263-5 |
| Category | Power Supply Chip |
| Pins | 6 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Output Voltage (ADJ, 8V≤VIN≤60V, 0.5A≤ILOAD≤3A) | VOUT | 1.193 | 1.23 | 1.267 | V | 8V≤VIN≤60V, VOUT=5V, 0.5A≤ILOAD≤3A | 5 |
| Output Voltage (ADJ, VIN=12V, IO=500mA) | VOUT | 1.217 | 1.23 | 1.243 | V | VIN=12V, IO=500mA, VOUT=5V | 5 |
| Oscillator Frequency | fo | 127 | 150 | 173 | kHz | 4 | |
| Feedback Bias Current | Ib | 50 | 100 | nA | Adjustable version only, VOUT=5V | 4 | |
| VSAT Saturation Voltage | VSAT | 1.4 | 1.8 | V | IOUT=3A | 4 | |
| Max. Duty Cycle (ON) | DC | 93 | 98 | % | 4 | ||
| Current Limit | ICL | 3.6 | 4.5 | 6.9 | A | Note 1 | 4 |
| Output Leakage Current (Output=0V) | IL | 2 | mA | Output=0V | 4 | ||
| Output Leakage Current (Output=-1V) | IL | 7.5 | 30 | mA | Output=-1V | 4 | |
| Quiescent Current | IQ | 5 | 10 | mA | 4 | ||
| Standby Quiescent Current | ISTBY | 50 | 200 | µA | ON / OFF pin=5V(OFF) | 4 | |
| ON / OFF Input Level High | VIH | 2 | V | VOUT=0V | 4 | ||
| ON / OFF Input Level Low | VIL | 0.8 | V | VOUT=nominal output voltage | 4 | ||
| ON / OFF Pin Input Current High | IIH | 12 | 30 | µA | ON / OFF pin=5V(OFF) | 4 | |
| ON / OFF Pin Input Current Low | IIL | 0 | 10 | µA | ON / OFF pin=0V(ON) | 4 | |
| Maximum Supply Voltage | VIN | 63 | V | 3 | |||
| ON / OFF Pin Input Voltage | ON / OFF | -0.3 | V | Printed as -0.3V≤V≤+VIN; upper limit is +VIN, not a number | 3 | ||
| Output Voltage to Ground (steady state) | VOUT | -1 | V | Steady state | 3 | ||
| Storage Temperature Range | Tstg | -65 | 150 | ℃ | 3 | ||
| Maximum Junction Temperature | TJA | 150 | ℃ | 3 | |||
| ESD Susceptibility (Human Body Model) | ESD | 2 | kV | Human Body Model | 3 | ||
| Lead Temperature (Soldering) | TL | 260 | ℃ | Soldering, 10 Seconds | 3 | ||
| Supply Voltage | VIN | 6 | 60 | V | 4 | ||
| Operating Temperature Range | Topr | -40 | 125 | ℃ | 4 |
Materials and finish
As the datasheet states them (page.json metadata.appearance; the 3D model's colours follow it).
| Part | Material | Colour / plating | Datasheet says | Page |
|---|---|---|---|---|
| contacts | copper | Internal switch, the voltage at this pin switches between (+VIN VSAT) and approximately -0.5V. To minimize coupling to sensitive circuitry, the PC board copper area connected to this pin should be kep | 3 |
CAD (KiCad official)
- Symbol:
D2596HV-ADJ - Footprint:
Package_TO_SOT_SMD:TO-263-5_TabPin6 - 3D model: TO-263-5 (KiCad packages3D, STEP)
- 3D model files:
d2596hv-adj-etched.step/d2596hv-adj-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);d2596hv-adj.step/d2596hv-adj.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Silicore datasheet (20 pp, sha256
8a405905e5297762, retrieved 2026-10-19, tier: lcsc) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).
# D2596HV-ADJ
**Silicore** · DC-DC Converters · TO-263-5
D2596HV-ADJ from Silicore, in a TO-263-5. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
## Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | VIN | power_in | Positive input supply for the switching regulator, which needs a suitable input bypass capacitor to minimize voltage transients and supply switching currents, with a recommended supply range of 6 V to 60 V (63 V absolute maximum). |
| 2 | OUTPUT | power_out | Internal switch output that swings between (+VIN − VSAT) and approximately −0.5 V, so the PC board copper connected to it should be kept to a minimum to limit coupling to sensitive circuitry. |
| 3 | GND | power_in | Circuit ground reference for the regulator. |
| 4 | FEEDBACK | input | Senses the regulated output voltage to complete the feedback loop; on the ADJ version it is the programming divider node, with a feedback bias current of 50 nA typical and 100 nA maximum at VOUT = 5 V, and resistors should not exceed 100 kΩ. |
| 5 | ON / OFF | input | Shuts the regulator down with logic levels: leave grounded or drive below 0.8 V (VIL) for normal operation and drive above 2.0 V (VIH) for standby, within a range of −0.3 V to +VIN, and it should not be left open. |
| 6 | EP | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |
## Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Silicore |
| Package | TO-263-5 |
| Category | Power Supply Chip |
| Pins | 6 |
## Electrical characteristics
Limits as printed in the datasheet (page.json `metadata.characteristics` carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Output Voltage (ADJ, 8V≤VIN≤60V, 0.5A≤ILOAD≤3A) | VOUT | 1.193 | 1.23 | 1.267 | V | 8V≤VIN≤60V, VOUT=5V, 0.5A≤ILOAD≤3A | 5 |
| Output Voltage (ADJ, VIN=12V, IO=500mA) | VOUT | 1.217 | 1.23 | 1.243 | V | VIN=12V, IO=500mA, VOUT=5V | 5 |
| Oscillator Frequency | fo | 127 | 150 | 173 | kHz | | 4 |
| Feedback Bias Current | Ib | | 50 | 100 | nA | Adjustable version only, VOUT=5V | 4 |
| VSAT Saturation Voltage | VSAT | | 1.4 | 1.8 | V | IOUT=3A | 4 |
| Max. Duty Cycle (ON) | DC | | 93 | 98 | % | | 4 |
| Current Limit | ICL | 3.6 | 4.5 | 6.9 | A | Note 1 | 4 |
| Output Leakage Current (Output=0V) | IL | | | 2 | mA | Output=0V | 4 |
| Output Leakage Current (Output=-1V) | IL | | 7.5 | 30 | mA | Output=-1V | 4 |
| Quiescent Current | IQ | | 5 | 10 | mA | | 4 |
| Standby Quiescent Current | ISTBY | | 50 | 200 | µA | ON / OFF pin=5V(OFF) | 4 |
| ON / OFF Input Level High | VIH | 2 | | | V | VOUT=0V | 4 |
| ON / OFF Input Level Low | VIL | | | 0.8 | V | VOUT=nominal output voltage | 4 |
| ON / OFF Pin Input Current High | IIH | | 12 | 30 | µA | ON / OFF pin=5V(OFF) | 4 |
| ON / OFF Pin Input Current Low | IIL | 0 | | 10 | µA | ON / OFF pin=0V(ON) | 4 |
| Maximum Supply Voltage | VIN | | | 63 | V | | 3 |
| ON / OFF Pin Input Voltage | ON / OFF | -0.3 | | | V | Printed as -0.3V≤V≤+VIN; upper limit is +VIN, not a number | 3 |
| Output Voltage to Ground (steady state) | VOUT | -1 | | | V | Steady state | 3 |
| Storage Temperature Range | Tstg | -65 | | 150 | ℃ | | 3 |
| Maximum Junction Temperature | TJA | | | 150 | ℃ | | 3 |
| ESD Susceptibility (Human Body Model) | ESD | | | 2 | kV | Human Body Model | 3 |
| Lead Temperature (Soldering) | TL | | | 260 | ℃ | Soldering, 10 Seconds | 3 |
| Supply Voltage | VIN | 6 | | 60 | V | | 4 |
| Operating Temperature Range | Topr | -40 | | 125 | ℃ | | 4 |
## Materials and finish
As the datasheet states them (page.json `metadata.appearance`; the 3D model's colours follow it).
| Part | Material | Colour / plating | Datasheet says | Page |
|---|---|---|---|---|
| contacts | copper | | Internal switch, the voltage at this pin switches between (+VIN VSAT) and approximately -0.5V. To minimize coupling to sensitive circuitry, the PC board copper area connected to this pin should be kep | 3 |
## CAD (KiCad official)
- Symbol: `D2596HV-ADJ`
- Footprint: `Package_TO_SOT_SMD:TO-263-5_TabPin6`
- 3D model: TO-263-5 (KiCad packages3D, STEP)
- 3D model files: `d2596hv-adj-etched.step` / `d2596hv-adj-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `d2596hv-adj.step` / `d2596hv-adj.glb` are the bare package body.
## Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- **Datasheet:** [Silicore datasheet](https://jlcpcb.com/api/file/downloadByFileSystemAccessId/8588944720164212736) (20 pp, sha256 `8a405905e5297762`, retrieved 2026-10-19, tier: lcsc)
- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.3`, primary `claude-haiku-5-5` (text), consensus `claude-sonnet-5-5` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
- **CAD:** KiCad official libraries (CC-BY-SA 4.0).
[Datasheet PDF](docs/d2596hv-adj-datasheet.pdf)