CN825R

{
 "schema": "adom.pads/1",
 "slug": "cn825r",
 "footprint": "SOT-23-6",
 "generated_from": {
  "footprint": "SOT-23-6@sha256:f341c73aac9dcb55",
  "pins": "page.json:component.pins",
  "overrides": null
 },
 "pin1": {
  "pad": "1",
  "at": [
   -1.1375,
   -0.95
  ],
  "corner": "top-left",
  "source": "silk-marker",
  "derived_from": "SOT-23-6@sha256:f341c73aac9dcb55"
 },
 "pad_count": 6,
 "symbol_pins": [
  "1",
  "2",
  "3",
  "4",
  "5",
  "6"
 ],
 "paste_apertures": 0,
 "issues": [],
 "pads": [
  {
   "pad": "1",
   "kind": "smd",
   "shape": "roundrect",
   "at": [
    -1.1375,
    -0.95
   ],
   "rot": 0.0,
   "size": [
    1.325,
    0.6
   ],
   "layers": [
    "F.Cu",
    "F.Mask",
    "F.Paste"
   ],
   "thermal": false,
   "pin": "1",
   "name": "/MR",
   "type": "input",
   "description": "Active-low manual reset input. Pulling this pin low triggers a reset pulse on both reset outputs. Internally pulled up to VCC via a ~50 kΩ resistor (38-62 kΩ), so it can be left floating, driven by CMOS, or driven by open-drain/open-collector logic. Minimum pulse width 1 µs; MR-to-reset delay ≤500 ns.",
   "is_pin1": true,
   "source": {
    "geometry": "SOT-23-6.kicad_mod",
    "meaning": "page.json:component.pins",
    "correspondence": "kicad: symbol pin number == pad name"
   }
  },
  {
   "pad": "2",
   "kind": "smd",
   "shape": "roundrect",
   "at": [
    -1.1375,
    0.0
   ],
   "rot": 0.0,
   "size": [
    1.325,
    0.6
   ],
   "layers": [
    "F.Cu",
    "F.Mask",
    "F.Paste"
   ],
   "thermal": false,
   "pin": "2",
   "name": "GND",
   "type": "power_in",
   "description": "Ground / negative supply return for the device.",
   "is_pin1": false,
   "source": {
    "geometry": "SOT-23-6.kicad_mod",
    "meaning": "page.json:component.pins",
    "correspondence": "kicad: symbol pin number == pad name"
   }
  },
  {
   "pad": "3",
   "kind": "smd",
   "shape": "roundrect",
   "at": [
    -1.1375,
    0.95
   ],
   "rot": 0.0,
   "size": [
    1.325,
    0.6
   ],
   "layers": [
    "F.Cu",
    "F.Mask",
    "F.Paste"
   ],
   "thermal": false,
   "pin": "3",
   "name": "/RESET",
   "type": "output",
   "description": "Active-low reset output. Driven low when VCC is below the 2.63 V reset threshold, when /MR is low, or when the watchdog times out. After the condition clears, /RESET stays low for at least 140 ms (typ. 200 ms) before returning high. VOL = 0.3 V max at 3.2 mA sink (150 µA at VCC = 1.1 V).",
   "is_pin1": false,
   "source": {
    "geometry": "SOT-23-6.kicad_mod",
    "meaning": "page.json:component.pins",
    "correspondence": "kicad: symbol pin number == pad name"
   }
  },
  {
   "pad": "4",
   "kind": "smd",
   "shape": "roundrect",
   "at": [
    1.1375,
    0.95
   ],
   "rot": 0.0,
   "size": [
    1.325,
    0.6
   ],
   "layers": [
    "F.Cu",
    "F.Mask",
    "F.Paste"
   ],
   "thermal": false,
   "pin": "4",
   "name": "VCC",
   "type": "power_in",
   "description": "Positive supply input, 1.1 V to 6.5 V operating range. This pin is continuously monitored and compared to the internal 2.63 V (CN825R) reset threshold. Supply current 2.7 µA typ. below threshold, 16 µA typ. above threshold. Abs max 6.5 V, 20 mA.",
   "is_pin1": false,
   "source": {
    "geometry": "SOT-23-6.kicad_mod",
    "meaning": "page.json:component.pins",
    "correspondence": "kicad: symbol pin number == pad name"
   }
  },
  {
   "pad": "5",
   "kind": "smd",
   "shape": "roundrect",
   "at": [
    1.1375,
    0.0
   ],
   "rot": 0.0,
   "size": [
    1.325,
    0.6
   ],
   "layers": [
    "F.Cu",
    "F.Mask",
    "F.Paste"
   ],
   "thermal": false,
   "pin": "5",
   "name": "RESET",
   "type": "output",
   "description": "Active-high reset output. Driven high when VCC is below the reset threshold, when /MR is low, or when the watchdog times out. After the condition clears, RESET stays high for at least 140 ms (typ. 200 ms) before returning low. VOH = VCC−1 V min at 1 mA source (1.0 V min at VCC = 1.1 V, 8 µA).",
   "is_pin1": false,
   "source": {
    "geometry": "SOT-23-6.kicad_mod",
    "meaning": "page.json:component.pins",
    "correspondence": "kicad: symbol pin number == pad name"
   }
  },
  {
   "pad": "6",
   "kind": "smd",
   "shape": "roundrect",
   "at": [
    1.1375,
    -0.95
   ],
   "rot": 0.0,
   "size": [
    1.325,
    0.6
   ],
   "layers": [
    "F.Cu",
    "F.Mask",
    "F.Paste"
   ],
   "thermal": false,
   "pin": "6",
   "name": "WDI",
   "type": "input",
   "description": "Watchdog input. If WDI is held high or low for more than the watchdog timeout (typ. 1.6 s, min 0.95 s, max 2.25 s) without a logic transition, the watchdog expires and asserts both reset outputs for ≥140 ms. Input high threshold 0.75·VCC, low threshold 0.25·VCC; input current ±50 nA; minimum detectable pulse width 50 ns.",
   "is_pin1": false,
   "source": {
    "geometry": "SOT-23-6.kicad_mod",
    "meaning": "page.json:component.pins",
    "correspondence": "kicad: symbol pin number == pad name"
   }
  }
 ]
}