component
CN3601
Public Made by Adomby adom
ShangHai Consonance Elec Battery Management, SSOP-10-150mil. Pinout cross-checked by two models against the datasheet, KiCad symbol/footprint/3D.
Made with KiCad 10.0 · needs KiCad 10.0 or later to open · KiCad file format 20260206
| Name | Last updated |
|---|---|
| docs | 17d ago |
| viewers | 17d ago |
| cn3601-etched.glb | 17d ago |
| cn3601-etched.step | 17d ago |
| cn3601-hero.glb | 17d ago |
| cn3601-hero.overlay.json | 17d ago |
| cn3601.glb | 17d ago |
| cn3601.kicad_mod | 17d ago |
| cn3601.kicad_sym | 17d ago |
| cn3601.lbr | 17d ago |
| cn3601.step | 17d ago |
| package.json | 17d ago |
| page.json | 17d ago |
| README.md | 17d ago |
CN3601
ShangHai Consonance Elec · Battery Management · SSOP-10-150mil
CN3601 from ShangHai Consonance Elec, in a SSOP-10-150mil. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | CHRG | output | Charge-status open-drain output that is pulled low by an internal N-MOSFET during constant-current and maintenance charging and is high-impedance in other states; the electrical table specifies a 10 mA sink at VCHRG = 0.3 V and 100 nA leakage at 6 V. |
| 2 | Isel | input | Inductor peak-current select input that accepts TTL or CMOS levels: high gives 1.19 A (typ.) in constant-current mode and 0.62 A in maintenance mode, low gives 0.64 A and 0.44 A, and voltages between 0.7 V and 2.2 V must not be applied. |
| 3 | TEMP | input | Battery temperature-monitor input driven by an NTC/resistor divider; charging pauses when TEMP falls below 44.5% of VIN and resumes when it rises more than 40 mV above that threshold, and it should be tied to VIN if the function is unused. |
| 4 | BAT | input | Battery positive connection and voltage feedback input that sets the charger state, with end-of-constant-current at 1.9 V (typ.), recharge threshold at 1.742 V (typ.), and overvoltage protection at 1.997 V (typ.). |
| 5 | GND | power_in | Ground connection for the input supply and the battery negative terminal. |
| 6 | SW | output | Inductor connection to the internal P-channel and N-channel power MOSFETs, with on-resistances of 0.4 Ω (P-channel to VIN) and 0.3 Ω (N-channel to GND). |
| 7 | VIN | power_in | Positive input supply that powers the internal circuits, operating from 2.7 V to 6.5 V with an absolute maximum of 7.0 V. |
| 8 | VIN | power_in | Second input supply pin listed as VIN, used with the same 2.7 V to 6.5 V input range. |
| 9 | DONE | output | Charge-done open-drain output that is pulled low when charging terminates and is high-impedance in other states; the electrical table specifies a 10 mA sink at VDONE = 0.3 V and 100 nA leakage at 6 V. |
| 10 | CT | passive | Timing-capacitor connection to GND that sets the maintenance-charge timer as t = 12.18×10^9 × C2 seconds (C2 in farads), with C2 required to be greater than 100 pF for timing accuracy. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | ShangHai Consonance Elec |
| Package | SSOP-10-150mil |
| Category | Power Management (PMIC) |
| Pins | 10 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Input voltage range | VIN | 2.7 | 6.5 | V | 4 | ||
| Battery overvoltage protection threshold (rising) | VOV | 1.967 | 1.997 | 2.027 | V | BAT voltage rising | 4 |
| Battery overvoltage release threshold (falling) | VOVRLS | 1.906 | 1.936 | 1.966 | V | BAT voltage falling | 4 |
| Constant-current charge end voltage (BAT rising) | VCCT | 1.881 | 1.9 | 1.919 | V | BAT pin voltage rising | 4 |
| Recharge threshold (BAT falling) | Vrech | 1.722 | 1.742 | 1.762 | V | BAT pin voltage falling | 4 |
| BAT pin current | IBAT | 4.7 | 6 | 8 | uA | VBAT=1.9V | 4 |
| TEMP pin input current | ITEMP | -100 | 100 | nA | 4 | ||
| TEMP comparator threshold | VTEMP | 42.5 | 44.5 | 46.5 | %VIN | TEMP pin voltage falling | 4 |
| Isel input low level | VL | 0.7 | V | Isel pin voltage falling | 4 | ||
| Isel input high level | VH | 2.2 | V | Isel pin voltage rising | 4 | ||
| Isel input current (low) | IL | -100 | nA | Isel=GND, VIN=6V | 4 | ||
| Isel input current (high) | IH | 100 | nA | Isel=VIN=6V | 4 | ||
| CHRG pin sink current | ISINK | 10 | mA | VCHRG=0.3V, charge mode | 4 | ||
| CHRG pin leakage current | ILEAK | 100 | nA | VCHRG=6V, charge end | 4 | ||
| DONE pin sink current | ISINK | 10 | mA | VDONE=0.3V, charge end | 4 | ||
| DONE pin leakage current | ILEAK | 100 | nA | VDONE=6V, charge mode | 4 | ||
| Fixed off time (charge mode) | toff | 1.2 | 1.5 | 1.8 | uS | Charge mode | 4 |
| UVLO threshold | VUVLO | 2.65 | V | 4 | |||
| Operating current | IVIN | 250 | 320 | 390 | uA | VBAT=2.1V, no switching | 4 |
| Over-temperature protection threshold | tOTP | 145 | °C | 4 | |||
| Over-temperature protection hysteresis | Hopt | 21 | °C | 4 | |||
| Inductor peak current ipeak (Isel high, constant-current charge) | ipeak | 1.19 | A | Isel high; constant-current charge mode | 4 | ||
| Inductor peak current ipeak (Isel high, maintenance charge) | ipeak | 0.62 | A | Isel high; maintenance charge mode | 4 | ||
| Inductor peak current ipeak (Isel low, constant-current charge) | ipeak | 0.64 | A | Isel low; constant-current charge mode | 4 | ||
| Inductor peak current ipeak (Isel low, maintenance charge) | ipeak | 0.44 | A | Isel low; maintenance charge mode | 4 | ||
| N-channel MOSFET on-resistance | RdsonN | 0.3 | ohm | N-channel MOSFET between SW and GND | 4 | ||
| P-channel MOSFET on-resistance | RdsonP | 0.4 | ohm | P-channel MOSFET between SW and VIN | 4 | ||
| TEMP comparator hysteresis | HTEMP | 40 | mV | 4 | |||
| Supply voltage on VIN and Isel pins | VIN, Isel | -0.3 | 7 | V | 3 | ||
| BAT pin voltage | BAT | -0.3 | 7 | V | 3 | ||
| Open-drain status output pin voltage (CHRG/DONE; symbol text not legible) | -0.3 | V | Upper limit printed as VIN | 3 | |||
| TEMP, SW and CT pin voltage | TEMP, SW, CT | -0.3 | V | Upper limit printed as VIN | 3 | ||
| Maximum junction temperature | 150 | °C | 3 | ||||
| Operating ambient temperature | -40 | 85 | °C | 3 | |||
| Storage temperature | -65 | 150 | °C | 3 |
CAD (KiCad official)
- Symbol:
CN3601 - Footprint:
Package_SO:SSOP-10_3.9x4.9mm_P1.00mm - 3D model: SSOP-10-150mil (KiCad packages3D, STEP)
- 3D model files:
cn3601-etched.step/cn3601-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);cn3601.step/cn3601.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: ShangHai Consonance Elec datasheet (10 pp, sha256
16d3e428c9f9006b, retrieved 2026-10-17, tier: lcsc) - Datasheet language: Chinese. Pin names, descriptions, and specs on this page were extracted and translated to English by ds2sf; the linked PDF is the manufacturer original.
- Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).