CI5930-10A from Tokmas, in a SOP-8. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin	Name	Type	Function
1	IP+	passive	Primary current input pin (IP+) of the internal low-resistance conductor, with input current flowing from IP+ to IP- counted as positive and isolated 3500 VRMS from pins 5-8.
2	IP+	passive	Primary current input pin (IP+) of the internal low-resistance conductor, with input current flowing from IP+ to IP- counted as positive and isolated 3500 VRMS from pins 5-8.
3	IP-	passive	Primary current return pin (IP-) of the internal low-resistance conductor, which must be connected in series with the measured circuit and must not be shunted by an external resistor.
4	IP-	passive	Primary current return pin (IP-) of the internal low-resistance conductor, which must be connected in series with the measured circuit and must not be shunted by an external resistor.
5	GND	power_in	Ground reference pin; the recommended input voltage limits VIN+ and VIN- are specified relative to this pin, with a maximum of 600 VPK.
6	VZCR	output	Zero current reference signal output with a maximum source current of 400 µA and maximum sink current of 3000 µA.
7	OUT	output	Analog voltage output that equals VCC/2 at zero current and changes by 200 mV/A for the 10A variant, accurate between 0.5 V and 4.5 V.
8	VCC	power_in	Single power supply input rated 4.5 V to 5.5 V recommended operation with an absolute maximum of 7 V.

Key specifications

Parameter	Value
Manufacturer	Tokmas
Package	SOP-8
Category	Sensors
Pins	8

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter	Symbol	Min	Typ	Max	Unit	Conditions	Page
Input voltage (relative to pin 5 GND)	VIN+, VIN-	-600		600	VPK	Voltage of IP+ and IP- relative to pin 5 (GND) (Note 1)	4
Input current (DC / AC RMS)	IP	-50		50	A	Decreases at higher ambient temperature (Note 2)	4
Power Supply	VCC	4.5		5.5	V		4
Operation Temperature	TA	-40		125	°C		4
Current Accuracy Range (10A part)	IP	-10		10	A		5
Sensitivity (10A part)	Sens	194	200	206	mV/A	full range of IP	5
Zero Current Differential Output Error (10A part)	VOE	-40		40	mV		5
Total Output Error (10A part)	ETOT	-3		3	%		5
Supply Current	ICC		20	25	mA	OUT pin floated	4
Internal benchmark	VZCR	2.47	2.5	2.53	V		4
Zero Current Output Voltage	VOUT(Q)	2.49	2.5	2.51	V	IP=0	4
Output Capacitance Load	CL			1	nF		4
Output Resistive Load	RL	1.5			kΩ		4
Res. of Primary Conductor	RP		0.9	1.2	mΩ	IP=2A	4
Rise Time	tr		1	2.2	μs		4
Common Mode Rejection Ratio	CMRR	38			dB		4
Bandwidth	BW	250			kHz	-3dB	4
Reference Output Source Current	IZCR(SOURCE)			400	μA		4
Reference Output Sink Current	IZCR(SINK)			3000	μA		4
Nonlinearity	LinERR		0.1	0.5	%		4
Symmetry	SymERR		0.5	1.5	%		4
Absolute Maximum Power Supply	VCC			7	V		3
Output Voltage	VOUT	-0.3			V	Printed as -0.3~VCC+0.3; upper limit is VCC+0.3, not a fixed number	3
Output Source Current	IOUT(SOURCE)			6	mA		3
Output Sink Current	IOUT(SINK)			30	mA		3
Input current peak current	IPEAK			100	A	3 s	3
Input current continuous current	ICON			40	A		3
Isolation Voltage	VISO			3500	VAC		3
Operating Ambient Temperature	Ta	-40		125	°C		3
Junction Temperature	TJ			165	°C		3
Storage Temperature	TS	-55		150	°C		3
Electrostatic Discharge Voltage (HBM)	ESD(HBM)			4000	V		3
Withstand isolation voltage	VISO			3500	VRMS	Test method: 50 / 60Hz, 1min	3
Test voltage	VTEST			3900	VRMS	t = 1s (100% production)	3
Working voltage of basic insulation	VWFSI			600	VPK	Basic insulation, UL standard 62368-1:2014	3
Working voltage of basic insulation	VWFSI			424	VRMS	Basic insulation, UL standard 62368-1:2014	3
Clearance	Dcl	3.8			mm	Minimum distance through air from IP leads to signal leads	3
Maximum repetitive peak isolation voltage	VIORM			600	VPK	AC voltage (bipolar)	4
Maximum working isolation voltage	VIOWM			424	VRMS	AC voltage (sine wave)	4
Maximum transient isolation voltage	VIOTM			4949	VPK	Test method: t = 60s (qualification)	4
Maximum transient isolation voltage	VIOTM			5515	VPK	VTEST t = 1s (100% production)	4
Maximum surge isolation voltage	VIOSM			7000	VPK	Tested 1.2us (rise) / 50us (width), one time	4
Surge Current	ISURGE			7.5	kA	Tested in compliance to IEC 61000-4-5, 8µs (rise) / 20µs (width)	4
Noise (10A part)	VNOISE(P-P)		55		mV		5
Zero Current Output Slope (10A part)	ΔVOUT(Q)		0.34		mV/℃		5
Sensitivity Slope (10A part)	ΔSENS		0.03		mV/A /℃		5
Power-on Time	TPOR		10		μs	Output rising from 0 to 90% of steady-state	4

Materials and finish

As the datasheet states them (page.json metadata.appearance; the 3D model's colours follow it).

Part	Material	Colour / plating	Datasheet says	Page
contacts	copper		The typical resistance of the primary current input conductor at 25 ° C is 0.9 mΩ. The lead frame is made of copper. The temperature	9

CAD (KiCad official)

Symbol: CI5930-10A
Footprint: Package_SO:SOIC-8_3.9x4.9mm_P1.27mm
3D model: SOP-8 (KiCad packages3D, STEP)
3D model files: ci5930-10a-etched.step / ci5930-10a-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); ci5930-10a.step / ci5930-10a.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

Datasheet: Tokmas datasheet (20 pp, sha256 e7a14d8bb93cf537, retrieved 2026-11-04, tier: lcsc)
Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-haiku-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF

CI5930-10A

Verified CI5930-10A

Verification log 1 record

3D Model

Symbol & Footprint

Schematic Symbol

PCB Footprint

Datasheet

README