component
CC6937S8-3FB005
Public Made by Adomby adom
Cross chip Current Sensors, SOP-8. Pinout cross-checked by two models against the datasheet, KiCad symbol/footprint/3D.
3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Contents
README
markdownCC6937S8-3FB005
Cross chip · Current Sensors · SOP-8
CC6937S8-3FB005 from Cross chip, in a SOP-8. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | IP+ | passive | Primary current input (current sampled +) carrying the measured current in series with the circuit; positive current flows from IP+ (pins 1-2) to IP- (pins 3-4), and pins 1-4 are isolated from pins 5-8 at 3750 VRMS. |
| 2 | IP+ | passive | Second primary current input pin (current sampled +) tied to pin 1; it carries the same measured current as the IP+ side and must be connected in series with the circuit, not shunted. |
| 3 | IP- | passive | Primary current output pin (current sampled -) where the measured current leaves the chip; it is the return end of the primary path and is isolated from pins 5-8 at 3750 VRMS. |
| 4 | IP- | passive | Second primary current output pin (current sampled -) tied to pin 3; the datasheet states not to place shunt resistors between IP+ and IP-. |
| 5 | GND | power_in | Ground reference for the secondary circuit; the datasheet lists it as the ground pin for the supply and output reference. |
| 6 | VREF | power_in | Reference voltage pin that works as an output (2.5 V nominal on 5 V series, 1.65 V on 3.3 V series, with 2 mA recommended load and 1.5 kΩ minimum load, 1 nF to 2.2 nF filter) or as an input (0 V to 4 V range) that sets the quiescent output VOQ. |
| 7 | VOUT | output | Analog output voltage that is proportional to the input current (VOUT = VREF + IP × sensitivity); it requires 1 nF to 2.2 nF to GND and a load of at least 1.5 kΩ to GND, and is short-circuit limited to 30 mA. |
| 8 | VCC | power_in | Supply voltage; the 3.3 V series operates at 3.0 V to 3.6 V (nominal 3.3 V) with undervoltage release at 2.8 V, and the absolute maximum is 6.5 V. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Cross chip |
| Package | SOP-8 |
| Category | Magnetic Sensors |
| Pins | 8 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Power Supply Voltage (3.3V nominal series) | VCC | 3 | 3.3 | 3.6 | V | Supply Section, VCC=3.3V | 5 |
| Quiescent Current (3.3V series) | ICC | 7 | 9 | 11 | mA | Supply Section, VCC=3.3V | 5 |
| Current Accuracy Range | IP | -5 | 5 | A | 10 | ||
| Zero Current Differential Output Error | VOE | -15 | 15 | mV | TA=25°C, VOE=VOUT-VREF, IP=0A | 10 | |
| Zero Current Output Offset Drift | ΔVOE | -50 | 50 | mV | TA=-40°C ~125°C; VOE offset voltage drift = VOE_TA - VOE_25℃ | 10 | |
| Zero Current Quiescent Output Voltage | VOUT(Q) | 1.64 | 1.65 | 1.66 | V | TA=25°C, IP=0A | 10 |
| Zero Current Quiescent Output Voltage Temperature Drift | ΔVOUT(Q) | -50 | 50 | mV | TA=-40°C ~125°C; VOUT(Q) voltage drift = VOUT(Q)_TA - VOUT(Q)_25℃ | 10 | |
| Sensitivity Error | ΔSENS | -2.5 | 2.5 | % | TA=-40°C ~ 125°C | 10 | |
| Total Output Error | ETOT | -3 | 3 | % | TA=-40°C ~ 125°C, IP=IP_MAX | 10 | |
| VOUT Filter Capacitors | COUT | 1 | 2.2 | nF | VOUT to GND | 5 | |
| VOUT Load Resistance | RL_OUT | 1.5 | kΩ | VOUT to GND | 5 | ||
| VOUT Output Short Circuit Current (to GND) | IOUT_SC_GND | 30 | mA | VOUT to GND short-circuit current | 5 | ||
| VOUT Output Short Circuit Current (to VCC) | IOUT_SC_VCC | 30 | mA | VOUT to VCC short-circuit current | 5 | ||
| VREF Filter Capacitors | CREF | 1 | 2.2 | nF | VOUT to GND | 5 | |
| VREF Load Resistance | RL_REF | 1.5 | kΩ | VOUT to GND | 5 | ||
| VREF Output Voltage (3.3V nominal supply series) | VREF | 1.6 | 1.65 | 1.7 | V | 3.3V nominal supply voltage series | 5 |
| VREF Input Voltage | VREFIN | 0 | 4 | V | VREF Input voltage range | 5 | |
| VREF Output Short Circuit Current (to GND) | IREF_SC_GND | 5 | mA | VREF to GND short-circuit current | 5 | ||
| VREF Output Short Circuit Current (to VCC) | IREF_SC_VCC | 5 | mA | VREF to VCC short-circuit current | 5 | ||
| Absolute Maximum Power Supply Voltage | VCC | 6.5 | V | 4 | |||
| Absolute Maximum Output Source Current | IOUT(SOURCE) | 25 | mA | 4 | |||
| Operating Ambient Temperature | TA | -40 | 125 | °C | 4 | ||
| Junction Temperature | TJ | 165 | °C | 4 | |||
| Storage Temperature | TS | -55 | 150 | °C | 4 | ||
| Electrostatic Discharge Voltage HBM | 4 | kV | HBM | 4 | |||
| Electrostatic Discharge Voltage CDM | 1 | kV | CDM | 4 | |||
| Latch Up | LU | 200 | mA | 4 | |||
| Withstand Isolation Voltage | VISO | 3750 | VRMS | Type test, 50/60Hz, 1min | 4 | ||
| Working Voltage for Basic Insulation | VWVBI | 834 | VPK / VDC | Basic Insulation UL/IEC 62368-1: 2018 | 4 | ||
| Working Voltage for Basic Insulation | VWVBI | 429 | VRMS | Basic Insulation UL/IEC 62368-1: 2018 | 4 | ||
| Working Voltage for Reinforced Insulation | VWVRI | 417 | VPK / VDC | Reinforced Insulation UL/IEC 62368-1: 2018 | 4 | ||
| Working Voltage for Reinforced Insulation | VWVRI | 214 | VRMS | Reinforced Insulation UL/IEC 62368-1: 2018 | 4 | ||
| Clearance | Dcl | 4.3 | mm | minimum distance through air from IP leads to signal leads | 4 | ||
| Creepage | Dcr | 4.3 | mm | minimum distance from the IP wire to the signal wire along the package | 4 | ||
| Comparative Tracking Index | CTI | 600 | V | 4 | |||
| Maximum Surge Isolation Voltage | VIOSM | 7 | kV | IEC 61000-4-5, tested in air, ± 5 pulses, 2 times/min, 1.2us (rise) / 50us (width) | 4 | ||
| Surge Current | ISURGE | 9 | kA | IEC 61000-4-5, tested in air, ± 5 pulses, 1 times/min, 8µs (rise) / 20µs (width) | 4 | ||
| Sensitivity (3.3V series, CC6937S8-3FB005) | Sens | 264 | mV/A | full range of IP | 10 | ||
| Noise | VN(RMS) | 45 | mV | IP=0A | 10 | ||
| Signal Chain -3dB Bandwidth | f-3dB | 230 | kHz | Small signal -3dB bandwidth | 5 | ||
| Signal Response Time | tRES | 1.5 | us | Input current up to 90% to VOUT 90% | 5 | ||
| Primary on-resistance | RP | 0.5 | mΩ | TA=25°C; IP= 2A | 5 |
Materials and finish
As the datasheet states them (page.json metadata.appearance; the 3D model's colours follow it).
| Part | Material | Colour / plating | Datasheet says | Page |
|---|---|---|---|---|
| contacts | copper | interference of external magnetic field. The typical resistance of the primary current input conductor at 25°C is 0.5mΩ. The lead frame is made of copper. The temperature | 28 |
CAD (KiCad official)
- Symbol:
CC6937S8-3FB005 - Footprint:
Package_SO:SOIC-8_3.9x4.9mm_P1.27mm - 3D model: SOP-8 (KiCad packages3D, STEP)
- 3D model files:
cc6937s8-3fb005-etched.step/cc6937s8-3fb005-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);cc6937s8-3fb005.step/cc6937s8-3fb005.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Cross chip datasheet (40 pp, sha256
7e94e7934f32e852, retrieved 2026-10-18, tier: lcsc) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).