CAT823TTDI-GT3

{
 "schema": "adom.pads/1",
 "slug": "cat823ttdi-gt3",
 "footprint": "SOT-23-5",
 "generated_from": {
  "footprint": "SOT-23-5@sha256:455a3f7c3e5eb5b8",
  "pins": "page.json:component.pins",
  "overrides": null
 },
 "pin1": {
  "pad": "1",
  "at": [
   -1.1375,
   -0.95
  ],
  "corner": "top-left",
  "source": "silk-marker",
  "derived_from": "SOT-23-5@sha256:455a3f7c3e5eb5b8"
 },
 "pad_count": 5,
 "symbol_pins": [
  "1",
  "2",
  "3",
  "4",
  "5"
 ],
 "paste_apertures": 0,
 "issues": [],
 "pads": [
  {
   "pad": "1",
   "kind": "smd",
   "shape": "roundrect",
   "at": [
    -1.1375,
    -0.95
   ],
   "rot": 0.0,
   "size": [
    1.325,
    0.6
   ],
   "layers": [
    "F.Cu",
    "F.Mask",
    "F.Paste"
   ],
   "thermal": false,
   "pin": "1",
   "name": "RESET",
   "type": "output",
   "description": "CMOS push-pull active-LOW reset output (RESET, bar). Driven low whenever VCC < VRST (3.08 V typ for the T version), while MR is held low, or on a watchdog timeout, then held low for tRP (200 ms typ, 400 ms max) after the fault clears. VOL <= 0.3 V at 1.2 mA sink; VOH >= 0.8 x VCC at 30 uA source.",
   "is_pin1": true,
   "source": {
    "geometry": "SOT-23-5.kicad_mod",
    "meaning": "page.json:component.pins",
    "correspondence": "kicad: symbol pin number == pad name"
   }
  },
  {
   "pad": "2",
   "kind": "smd",
   "shape": "roundrect",
   "at": [
    -1.1375,
    0.0
   ],
   "rot": 0.0,
   "size": [
    1.325,
    0.6
   ],
   "layers": [
    "F.Cu",
    "F.Mask",
    "F.Paste"
   ],
   "thermal": false,
   "pin": "2",
   "name": "GND",
   "type": "power_in",
   "description": "Ground / device return. 0 V reference for all logic thresholds and outputs.",
   "is_pin1": false,
   "source": {
    "geometry": "SOT-23-5.kicad_mod",
    "meaning": "page.json:component.pins",
    "correspondence": "kicad: symbol pin number == pad name"
   }
  },
  {
   "pad": "3",
   "kind": "smd",
   "shape": "roundrect",
   "at": [
    -1.1375,
    0.95
   ],
   "rot": 0.0,
   "size": [
    1.325,
    0.6
   ],
   "layers": [
    "F.Cu",
    "F.Mask",
    "F.Paste"
   ],
   "thermal": false,
   "pin": "3",
   "name": "MR",
   "type": "input",
   "description": "Manual Reset input (MR, active low). Internally pulled high by a 52 kOhm (35-75 kOhm) resistor and designed to be driven low by a pushbutton, open-drain, or CMOS output. Pulling MR low asserts RESET; on release the reset stays active for tRP (140 ms min). VIL <= 0.3 x VCC, VIH >= 0.7 x VCC, minimum valid pulse width tPB = 1 us, noise immunity 100 ns.",
   "is_pin1": false,
   "source": {
    "geometry": "SOT-23-5.kicad_mod",
    "meaning": "page.json:component.pins",
    "correspondence": "kicad: symbol pin number == pad name"
   }
  },
  {
   "pad": "4",
   "kind": "smd",
   "shape": "roundrect",
   "at": [
    1.1375,
    0.95
   ],
   "rot": 0.0,
   "size": [
    1.325,
    0.6
   ],
   "layers": [
    "F.Cu",
    "F.Mask",
    "F.Paste"
   ],
   "thermal": false,
   "pin": "4",
   "name": "WDI",
   "type": "input",
   "description": "Watchdog Timer Input. Must see a low-to-high or high-to-low transition within tWD (1.6 s typ, 3.2 s max) or RESET is pulled active for tRP. Can be disabled by leaving open or tri-stating (internally serviced within the timeout period). VIL <= 0.3 x VCC, VIH >= 0.7 x VCC, min pulse width 50 ns.",
   "is_pin1": false,
   "source": {
    "geometry": "SOT-23-5.kicad_mod",
    "meaning": "page.json:component.pins",
    "correspondence": "kicad: symbol pin number == pad name"
   }
  },
  {
   "pad": "5",
   "kind": "smd",
   "shape": "roundrect",
   "at": [
    1.1375,
    -0.95
   ],
   "rot": 0.0,
   "size": [
    1.325,
    0.6
   ],
   "layers": [
    "F.Cu",
    "F.Mask",
    "F.Paste"
   ],
   "thermal": false,
   "pin": "5",
   "name": "VCC",
   "type": "power_in",
   "description": "Supply voltage input. Recommended operating range 1.2 to 5.5 V (over -40 to +85 C); absolute maximum 6 V. Typical supply current ICC = 4 uA (12 uA max) for the CAT823 T version. Monitored against the VRST threshold (3.08 V typ for T suffix) to generate RESET.",
   "is_pin1": false,
   "source": {
    "geometry": "SOT-23-5.kicad_mod",
    "meaning": "page.json:component.pins",
    "correspondence": "kicad: symbol pin number == pad name"
   }
  }
 ]
}