component
CAT25640YI-GT3
Public Made by Adomby adom
onsemi EEPROM, TSSOP-8. Pinout cross-checked by two models against the datasheet, KiCad symbol/footprint/3D.
3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
README
markdownCAT25640YI-GT3
onsemi · EEPROM · TSSOP-8
CAT25640YI-GT3 from onsemi, in a TSSOP-8. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | CS | input | Chip select input enables the device; a high-to-low transition starts each session and a low-to-high transition ends it, and SO is tri-stated while CS is high. |
| 2 | SO | tri_state | Serial data output shifts data out on the falling edge of SCK in SPI modes (0,0) and (1,1) and is high impedance when CS is high or HOLD is asserted. |
| 3 | WP | input | Write protect input allows all write operations when high; when low with the WPEN bit set to 1, writes to the Status Register are disabled. |
| 4 | VSS | power_in | Ground reference for the device. |
| 5 | SI | input | Serial data input accepts op-codes, addresses and data, and is latched on the rising edge of SCK. |
| 6 | SCK | input | Serial clock input provided by the host to synchronize communication with the device. |
| 7 | HOLD | input | Hold input pauses serial transmission when taken low while SCK is low and resumes when taken high while SCK is low; tie to VCC when not used. |
| 8 | VCC | power_in | Power supply input, 1.8 V to 5.5 V. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | onsemi |
| Package | TSSOP-8 |
| Category | Memory |
| Pins | 8 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Operating Temperature | -45 | 130 | °C | 2 | |||
| Storage Temperature | -65 | 150 | °C | 2 | |||
| Voltage on any Pin with Respect to Ground | -0.5 | 6.5 | V | Note 1 | 2 | ||
| Supply Voltage Range | VCC | 1.8 | 5.5 | V | TA = −40°C to +85°C | 2 | |
| Ambient Temperature (Industrial) | TA | -40 | 85 | °C | VCC = 1.8 V to 5.5 V | 2 | |
| Supply Current (Read Mode) | ICCR | 0.2 | mA | Read, SO open / −40°C to +85°C; VCC = 1.8 V, fSCK = 5 MHz | 3 | ||
| Supply Current (Read Mode) | ICCR | 0.3 | mA | Read, SO open / −40°C to +85°C; VCC = 2.5 V, fSCK = 10 MHz | 3 | ||
| Supply Current (Read Mode) | ICCR | 0.6 | mA | Read, SO open / −40°C to +85°C; VCC = 5.5 V, fSCK = 20 MHz | 3 | ||
| Supply Current (Write Mode) | ICCW | 0.8 | mA | Write, CS = VCC / −40°C to +85°C; VCC = 1.8 V | 3 | ||
| Supply Current (Write Mode) | ICCW | 1.4 | mA | Write, CS = VCC / −40°C to +85°C; VCC = 2.5 V | 3 | ||
| Supply Current (Write Mode) | ICCW | 2 | mA | Write, CS = VCC / −40°C to +85°C; VCC = 5.5 V | 3 | ||
| Standby Current | ISB1 | 1 | µA | VIN = GND or VCC, CS = VCC, WP = VCC, VCC = 5.5 V; TA = −40°C to +85°C | 3 | ||
| Standby Current | ISB1 | 3 | µA | VIN = GND or VCC, CS = VCC, WP = VCC, VCC = 5.5 V; TA = −40°C to +125°C | 3 | ||
| Standby Current | ISB2 | 5 | µA | VIN = GND or VCC, CS = VCC, WP = GND, VCC = 5.5 V; TA = −40°C to +125°C | 3 | ||
| Input Leakage Current | IL | -2 | 2 | µA | VIN = GND or VCC | 3 | |
| Output Leakage Current | ILO | -1 | 1 | µA | CS = VCC, VOUT = GND or VCC; TA = −40°C to +85°C | 3 | |
| Output Leakage Current | ILO | -1 | 2 | µA | CS = VCC, VOUT = GND or VCC; TA = −40°C to +125°C | 3 | |
| Input Low Voltage | VIL | -0.5 | V | 3 | |||
| Output Low Voltage | VOL1 | 0.4 | V | VCC > 2.5 V, IOL = 3.0 mA | 3 | ||
| Output Low Voltage | VOL2 | 0.2 | V | VCC < 2.5 V, IOL = 150 µA | 3 | ||
| Output Capacitance (SO) | COUT | 8 | pF | VOUT = 0 V; TA = 25°C, f = 1.0 MHz, VCC = +5.0 V | 3 | ||
| Input Capacitance (CS, SCK, SI, WP, HOLD) | CIN | 8 | pF | VIN = 0 V; TA = 25°C, f = 1.0 MHz, VCC = +5.0 V | 3 | ||
| Clock Frequency | fSCK | 5 | MHz | VCC = 1.8 V − 5.5 V, −40°C to +85°C | 5 | ||
| Data Setup Time | tSU | 20 | ns | VCC = 1.8 V − 5.5 V, −40°C to +85°C | 5 | ||
| Data Hold Time | tH | 20 | ns | VCC = 1.8 V − 5.5 V, −40°C to +85°C | 5 | ||
| SCK High Time | tWH | 75 | ns | VCC = 1.8 V − 5.5 V, −40°C to +85°C | 5 | ||
| SCK Low Time | tWL | 75 | ns | VCC = 1.8 V − 5.5 V, −40°C to +85°C | 5 | ||
| HOLD to Output Low Z | tLZ | 50 | ns | VCC = 1.8 V − 5.5 V, −40°C to +85°C | 5 | ||
| Input Rise Time | tRI | 2 | µs | Note 10; VCC = 1.8 V − 5.5 V, −40°C to +85°C | 5 | ||
| Input Fall Time | tFI | 2 | µs | Note 10; VCC = 1.8 V − 5.5 V, −40°C to +85°C | 5 | ||
| HOLD Setup Time | tHD | 0 | ns | VCC = 1.8 V − 5.5 V, −40°C to +85°C | 5 | ||
| HOLD Hold Time | tCD | 10 | ns | VCC = 1.8 V − 5.5 V, −40°C to +85°C | 5 | ||
| Output Valid from Clock Low | tV | 70 | ns | VCC = 1.8 V − 5.5 V, −40°C to +85°C | 5 | ||
| Output Hold Time | tHO | 0 | ns | VCC = 1.8 V − 5.5 V, −40°C to +85°C | 5 | ||
| Output Disable Time | tDIS | 50 | ns | VCC = 1.8 V − 5.5 V, −40°C to +85°C | 5 | ||
| HOLD to Output High Z | tHZ | 100 | ns | VCC = 1.8 V − 5.5 V, −40°C to +85°C | 5 | ||
| CS High Time | tCS | 80 | ns | VCC = 1.8 V − 5.5 V, −40°C to +85°C | 5 | ||
| CS Setup Time | tCSS | 30 | ns | VCC = 1.8 V − 5.5 V, −40°C to +85°C | 5 | ||
| CS Hold Time | tCSH | 30 | ns | VCC = 1.8 V − 5.5 V, −40°C to +85°C | 5 | ||
| CS Inactive Setup Time | tCNS | 20 | ns | VCC = 1.8 V − 5.5 V, −40°C to +85°C | 5 | ||
| CS Inactive Hold Time | tCNH | 20 | ns | VCC = 1.8 V − 5.5 V, −40°C to +85°C | 5 | ||
| WP Setup Time | tWPS | 10 | ns | VCC = 1.8 V − 5.5 V, −40°C to +85°C | 5 | ||
| WP Hold Time | tWPH | 10 | ns | VCC = 1.8 V − 5.5 V, −40°C to +85°C | 5 | ||
| Write Cycle Time | tWC | 5 | ms | Note 11; VCC = 1.8 V − 5.5 V, −40°C to +85°C | 5 | ||
| Power-up to Read Operation | tPUR | 1 | ms | Notes 10, 12 | 5 | ||
| Power-up to Write Operation | tPUW | 1 | ms | Notes 10, 12 | 5 |
CAD (KiCad official)
- Symbol:
CAT25640YI-GT3 - Footprint:
Package_SO:TSSOP-8_3x3mm_P0.65mm - 3D model: TSSOP-8 (KiCad packages3D, STEP)
- 3D model files:
cat25640yi-gt3-etched.step/cat25640yi-gt3-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);cat25640yi-gt3.step/cat25640yi-gt3.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: onsemi datasheet (17 pp, sha256
fd49d7d75cf81fda, retrieved 2026-10-19, tier: lcsc) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).