component

CAT25320YI-GT3

Public Made by Adom

by adom

onsemi EEPROM, TSSOP-8. Pinout cross-checked by two models against the datasheet, KiCad symbol/footprint/3D.

componentmemorycat25320yi-gt3factory-2.0.0extractor-text
Overview Files Discover Packages Releases Dependencies Issues Breadcrumbs Pull Requests Activity

3D Model

Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.

Symbol & Footprint

Schematic Symbol

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.

PCB Footprint

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.

Datasheet

Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Download PDF
Contents

README

markdown

CAT25320YI-GT3

onsemi · EEPROM · TSSOP-8

CAT25320YI-GT3 from onsemi, in a TSSOP-8. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 CS input The chip select input enables or disables the device; CS must go high-to-low before each session and low-to-high to end it, and when CS is high SO is tri-stated and the device is in Standby Mode.
2 SO output The serial data output transfers data out of the device on the falling edge of SCK in SPI modes (0,0) and (1,1), and is high impedance when CS is high or during HOLD.
3 WP input The write protect input allows all write operations when held high, and when tied low with the WPEN status register bit set to 1 it disables writing to the Status Register.
4 VSS power_in Ground reference for the device; DC input voltages must not be lower than -0.5 V with respect to ground.
5 SI input The serial data input accepts op-codes, addresses and data, latched on the rising edge of SCK in SPI modes (0,0) and (1,1).
6 SCK input The serial clock input accepts the clock from the host to synchronize communication between host and device.
7 HOLD input The HOLD input pauses serial communication when taken low while SCK is low (SO tri-stated, SI ignored) and resumes when taken high while SCK is low; when unused it should be tied to VCC directly or through a resistor.
8 VCC power_in Power supply input, rated 1.8 V to 5.5 V per the Features list; voltage on any pin must not exceed VCC + 0.5 V.

Key specifications

Parameter Value
Manufacturer onsemi
Package TSSOP-8
Category Memory
Pins 8

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
Supply Voltage VCC 1.8 5.5 V Industrial grade (TA −40°C to +85°C) 2
Operating Temperature (Industrial) TA -40 85 °C Industrial grade 2
Operating Temperature -45 130 °C 2
Storage Temperature -65 150 °C 2
Voltage on any Pin with Respect to Ground -0.5 6.5 V 2
Endurance NEND 1e+06 Program / Erase Cycles Page Mode, VCC = 5 V, 25°C 2
Data Retention TDR 100 Years 2
Read Supply Current ICCR 2 mA Read, VCC = 5.5 V, SO open; 10 MHz / −40°C to 85°C 2
Write Supply Current ICCW 2 mA Write, VCC = 5.5 V, SO open; 10 MHz / −40°C to 85°C 2
Standby Current ISB1 1 A VIN = GND or VCC, CS = VCC, WP = VCC, VCC = 5.5 V; TA = −40°C to +85°C 2
Standby Current ISB2 3 A VIN = GND or VCC, CS = VCC, WP = GND, VCC = 5.5 V; TA = −40°C to +85°C 2
Input Leakage Current IL -2 2 A VIN = GND or VCC 2
Output Leakage Current ILO -1 1 A CS = VCC, VOUT = GND or VCC; TA = −40°C to +85°C 2
Input Low Voltage VIL -0.5 V 2
Output Low Voltage VOL1 0.4 V VCC ≥ 2.5 V, IOL = 3.0 mA 2
Output Low Voltage VOL2 0.2 V VCC < 2.5 V, IOL = 150 A 2
Output Capacitance (SO) COUT 8 pF VOUT = 0 V 2
Input Capacitance (CS, SCK, SI, WP, HOLD) CIN 8 pF VIN = 0 V 2
Clock Frequency fSCK 5 MHz VCC = 1.8 V − 5.5 V, −40C to +85C 3
Data Setup Time tSU 40 ns VCC = 1.8 V − 5.5 V, −40C to +85C 3
Data Hold Time tH 40 ns VCC = 1.8 V − 5.5 V, −40C to +85C 3
SCK High Time tWH 75 ns VCC = 1.8 V − 5.5 V, −40C to +85C 3
SCK Low Time tWL 75 ns VCC = 1.8 V − 5.5 V, −40C to +85C 3
HOLD to Output Low Z tLZ 50 ns VCC = 1.8 V − 5.5 V, −40C to +85C 3
Input Rise Time tRI 2 s VCC = 1.8 V − 5.5 V, −40C to +85C; Note 5 3
Input Fall Time tFI 2 s VCC = 1.8 V − 5.5 V, −40C to +85C; Note 5 3
HOLD Setup Time tHD 0 ns VCC = 1.8 V − 5.5 V, −40C to +85C 3
HOLD Hold Time tCD 10 ns VCC = 1.8 V − 5.5 V, −40C to +85C 3
Output Valid from Clock Low tV 75 ns VCC = 1.8 V − 5.5 V, −40C to +85C 3
Output Hold Time tHO 0 ns VCC = 1.8 V − 5.5 V, −40C to +85C 3
Output Disable Time tDIS 50 ns VCC = 1.8 V − 5.5 V, −40C to +85C 3
HOLD to Output High Z tHZ 100 ns VCC = 1.8 V − 5.5 V, −40C to +85C 3
CS High Time tCS 50 ns VCC = 1.8 V − 5.5 V, −40C to +85C 3
CS Setup Time tCSS 20 ns VCC = 1.8 V − 5.5 V, −40C to +85C 3
CS Hold Time tCSH 30 ns VCC = 1.8 V − 5.5 V, −40C to +85C 3
CS Inactive Setup Time tCNS 50 ns VCC = 1.8 V − 5.5 V, −40C to +85C 3
CS Inactive Hold Time tCNH 50 ns VCC = 1.8 V − 5.5 V, −40C to +85C 3
WP Setup Time tWPS 10 ns VCC = 1.8 V − 5.5 V, −40C to +85C 3
WP Hold Time tWPH 100 ns VCC = 1.8 V − 5.5 V, −40C to +85C 3
Write Cycle Time tWC 5 ms Note 6 3
Power-up to Read Operation tPUR 1 ms 3
Power-up to Write Operation tPUW 1 ms 3

CAD (KiCad official)

  • Symbol: CAT25320YI-GT3
  • Footprint: Package_SO:TSSOP-8_3x3mm_P0.65mm
  • 3D model: TSSOP-8 (KiCad packages3D, STEP)
  • 3D model files: cat25320yi-gt3-etched.step / cat25320yi-gt3-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); cat25320yi-gt3.step / cat25320yi-gt3.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: onsemi datasheet (13 pp, sha256 7b0b8c99eaddcd32, retrieved 2026-10-20, tier: lcsc)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-haiku-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF