Loads on click. Unloads only if this page sits in the background.

Symbol & Footprint

Schematic Symbol

Open full view ↗
Loads on click. Unloads only if this page sits in the background.

PCB Footprint

Open full view ↗
Loads on click. Unloads only if this page sits in the background.
Loads on click. Unloads only if this page sits in the background.
Download PDF
Contents

README

markdown

BRCL4056SE

Foshan Blue Rocket Elec · Battery Management · ESOP-8

BRCL4056SE from Foshan Blue Rocket Elec, in a ESOP-8. Pinout and pin descriptions extracted from the manufacturer datasheet by ds2sf; symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 TEMP input Battery temperature sense input. Connect to the output of an NTC thermistor on the battery pack. Charging is paused if V(TEMP) < 45%·VCC or > 80%·VCC (battery too hot/cold), and resumes when the voltage returns inside that window. Tie to GND to disable the temperature-monitoring function.
2 PROG passive Charge-current program and monitor pin. A resistor R_PROG from PROG to GND sets the charge current: precharge clamps V(PROG) to 0.1V and constant-current mode regulates V(PROG) to 1.0V, so I_BAT = (V_PROG / R_PROG) × 1000. The pin voltage can also be read to monitor instantaneous charge current in all charge states.
3 GND power_in Device ground / power return.
4 VCC power_in Positive supply input, 4.5V-6.5V operating range (absolute max 10V). Powers the internal circuitry and the pass FET to the battery. When (VCC − V_BAT) falls below ~80mV, the part enters low-power sleep mode and BAT sink current drops below 2µA.
5 BAT power_out Battery connection / charge output. Sources charge current to the single-cell Li+ pack and regulates it to 4.2V float. Draws less than 2µA from the battery when the part is disabled or in sleep mode.
6 STDBY output Open-drain charge-complete (standby) indicator. Internal switch pulls low when charging has terminated (battery full); otherwise the pin is high-impedance. Absolute max sink current 10mA - typically drives an LED to VCC through a series resistor.
7 CHRG output Open-drain charging-in-progress indicator. Internal switch pulls low while the charger is actively delivering current to the battery; otherwise the pin is high-impedance. Absolute max sink current 10mA - typically drives an LED to VCC through a series resistor.
8 CE input Chip-enable input. Logic high enables normal charging operation; logic low forces the device into charge-disabled state. Compatible with TTL and CMOS logic levels (V_IH ≥ 1.5V, V_IL ≤ 0.4V).
9 EPAD power_in Exposed thermal pad on the package bottom. Must be soldered to a PCB ground copper plane to achieve the specified thermal performance and to provide electrical ground contact.

Key specifications

Parameter Value
Manufacturer Foshan Blue Rocket Elec
Package ESOP-8
Category PMIC
Pins 9

Ordering variants

  • BRCL4056SE

CAD (KiCad official)

  • Symbol: BRCL4056SE
  • Footprint: Package_SO:SOIC-8-1EP_3.9x4.9mm_P1.27mm_EP2.29x3mm
  • 3D model: ESOP-8 (KiCad packages3D, STEP)
  • 3D model files: brcl4056se-etched.step / brcl4056se-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); brcl4056se.step / brcl4056se.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: Foshan Blue Rocket Elec datasheet (11 pp, sha256 be9b7b61a6cb5090, retrieved 2026-08-17, tier: lcsc)
  • Datasheet language: Chinese. Pin names, descriptions, and specs on this page were extracted and translated to English by ds2sf; the linked PDF is the manufacturer original.
  • Extractor: ds2sf (Claude). Every pin and dimension is cited to a datasheet page; it refuses to fabricate.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF