← Commit history

Initial commit: component/bq51050brhlr

Ray ·02b675179d ·
2 files changed +280
README.mdadded+58
@@ -0,0 +1,58 @@+# BQ51050BRHLR++**Texas Instruments** · Battery Management · QFN-20-EP(3.7x4.7)++BQ51050BRHLR from Texas Instruments, in a QFN-20-EP(3.7x4.7). Pinout and pin descriptions extracted from the manufacturer datasheet by ds2sf; symbol, footprint, and 3D from KiCad-official CAD.++## Pinout++| Pin | Name | Type | Function |+|---|---|---|---|+| 1 | PGND | power_in | Power ground connection for the device. |+| 2 | AC1 | input | AC power input from receiver coil with maximum input voltage of 20V and 2A RMS current rating. |+| 3 | BOOT1 | output | Bootstrap output for driving high-side FETs of synchronous rectifier; connect 10-nF ceramic capacitor from BOOT1 to AC1. |+| 4 | BAT | power_out | Output pin delivering regulated power to battery at 4.20V with maximum 1.5A charging current. |+| 5 | CLAMP1 | output | Open-drain FET output for non-power dissipative overvoltage AC clamp protection; activates when RECT voltage exceeds 15V threshold. |+| 6 | COMM1 | output | Open-drain output for load modulation communication with primary; connect capacitor from COMM1 to AC1 for capacitive load modulation. |+| 7 | CHG | output | Open-drain status output active when BAT output is enabled with maximum 15mA sink current rating. |+| 8 | AD-EN | output | Push-pull driver output for external PFET control when wired charging is active; float if not used. |+| 9 | AD | input | Adapter voltage detection input with 3.6V typical presence threshold and maximum 30V rating; connect 1-µF capacitor to PGND or direct to PGND if unused. |+| 10 | TERM | input | Termination threshold programming input; sets termination current as percentage of programmed charge current IBULK. |+| 11 | EN2 | input | Priority control input between wireless power and wired power with 1.3V high threshold; EN2 low enables wired charging when AD present. |+| 12 | ILIM | bidirectional | Current programming pin where total resistance RILIM from ILIM to PGND sets charging current from 500mA to 1.5A; KILIM factor is 314 AΩ. |+| 13 | TS/CTRL | input | Temperature sense input for NTC thermistor monitoring with 2.2V internal bias voltage; connect NTC resistor to PGND or 10-kΩ resistor if NTC not used. |+| 14 | FOD | input | Foreign object detection power measurement input for WPC v1.2 compatibility with 0-5W received power measurement range. |+| 15 | COMM2 | output | Open-drain output for load modulation communication with primary; connect capacitor from COMM2 to AC2 for capacitive load modulation. |+| 16 | CLAMP2 | output | Open-drain FET output for non-power dissipative overvoltage AC clamp protection; activates when RECT voltage exceeds 15V threshold. |+| 17 | BOOT2 | output | Bootstrap output for driving high-side FETs of synchronous rectifier; connect 10-nF ceramic capacitor from BOOT2 to AC2. |+| 18 | RECT | output | Filtered rectifier output node; connect ceramic capacitor from 4.7µF to 22µF to PGND depending on power level. |+| 19 | AC2 | input | AC power input from receiver coil with maximum input voltage of 20V and 2A RMS current rating. |+| 20 | PGND | power_in | Power ground connection for the device. |+| 21 | EP | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |++## Key specifications++| Parameter | Value |+|---|---|+| Manufacturer | Texas Instruments |+| Package | QFN-20-EP(3.7x4.7) |+| Category | Power Management (PMIC) |+| Pins | 21 |++## CAD (KiCad official)++- Symbol: `BQ51050BRHLR`+- Footprint: `Package_DFN_QFN:QFN-20-1EP_4x5mm_P0.5mm_EP2.65x3.65mm`+- 3D model: QFN-20-EP(3.7x4.7) (KiCad packages3D, STEP)+- 3D model files: `bq51050brhlr-etched.step` / `bq51050brhlr-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `bq51050brhlr.step` / `bq51050brhlr.glb` are the bare package body.++## Provenance++Data extracted from the manufacturer datasheet, not a distributor listing:++- **Datasheet:** [Texas Instruments datasheet](https://www.ti.com/cn/lit/gpn/bq51050b) (44 pp, sha256 `38293c82dac0e8d1`, retrieved 2026-09-22, tier: lcsc)+- **Datasheet language:** Chinese. Pin names, descriptions, and specs on this page were extracted and translated to English by ds2sf; the linked PDF is the manufacturer original.+- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.2`, primary `claude-haiku-4-5-20251001` (text), consensus `claude-sonnet-5` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.+- **CAD:** KiCad official libraries (CC-BY-SA 4.0).++[Datasheet PDF](docs/bq51050brhlr-datasheet.pdf)
page.jsonadded+222
@@ -0,0 +1,222 @@+{+  "slug": "bq51050brhlr",+  "version": "0.1.0",+  "type": "component",+  "description": "Texas Instruments Battery Management, QFN-20-EP(3.7x4.7). Datasheet-verified pinout, KiCad symbol/footprint/3D.",+  "tags": [+    "component",+    "power management (pmic)",+    "bq51050brhlr",+    "factory-2.0.0",+    "extractor-text"+  ],+  "dependencies": {},+  "hero": {+    "type": "image",+    "path": "docs/hero.png"+  },+  "files": [+    "page.json",+    "README.md",+    "bq51050brhlr.kicad_sym",+    "bq51050brhlr.kicad_mod",+    "bq51050brhlr.glb",+    "bq51050brhlr.step",+    "bq51050brhlr.lbr",+    "docs/hero.png",+    "docs/bq51050brhlr-datasheet.pdf",+    "viewers/symbol.html",+    "viewers/footprint.html"+  ],+  "component": {+    "mpn": "BQ51050BRHLR",+    "manufacturer": "Texas Instruments",+    "package": "QFN-20-EP(3.7x4.7)",+    "pin_count": 21,+    "category": "Power Management (PMIC)",+    "subcategory": "Battery Management",+    "datasheet": "https://www.ti.com/cn/lit/gpn/bq51050b",+    "parts": {+      "symbol": "bq51050brhlr.kicad_sym",+      "footprint": "bq51050brhlr.kicad_mod",+      "model_3d": "bq51050brhlr-etched.glb",+      "model_3d_plain": "bq51050brhlr.glb",+      "model_3d_step": "bq51050brhlr-etched.step",+      "model_3d_step_plain": "bq51050brhlr.step",+      "lbr": "bq51050brhlr.lbr"+    },+    "distributor_links": {+      "lcsc": "C133307"+    },+    "pins": [+      {+        "number": "1",+        "name": "PGND",+        "type": "power_in",+        "description": "Power ground connection for the device."+      },+      {+        "number": "2",+        "name": "AC1",+        "type": "input",+        "description": "AC power input from receiver coil with maximum input voltage of 20V and 2A RMS current rating."+      },+      {+        "number": "3",+        "name": "BOOT1",+        "type": "output",+        "description": "Bootstrap output for driving high-side FETs of synchronous rectifier; connect 10-nF ceramic capacitor from BOOT1 to AC1."+      },+      {+        "number": "4",+        "name": "BAT",+        "type": "power_out",+        "description": "Output pin delivering regulated power to battery at 4.20V with maximum 1.5A charging current."+      },+      {+        "number": "5",+        "name": "CLAMP1",+        "type": "output",+        "description": "Open-drain FET output for non-power dissipative overvoltage AC clamp protection; activates when RECT voltage exceeds 15V threshold."+      },+      {+        "number": "6",+        "name": "COMM1",+        "type": "output",+        "description": "Open-drain output for load modulation communication with primary; connect capacitor from COMM1 to AC1 for capacitive load modulation."+      },+      {+        "number": "7",+        "name": "CHG",+        "type": "output",+        "description": "Open-drain status output active when BAT output is enabled with maximum 15mA sink current rating."+      },+      {+        "number": "8",+        "name": "AD-EN",+        "type": "output",+        "description": "Push-pull driver output for external PFET control when wired charging is active; float if not used."+      },+      {+        "number": "9",+        "name": "AD",+        "type": "input",+        "description": "Adapter voltage detection input with 3.6V typical presence threshold and maximum 30V rating; connect 1-µF capacitor to PGND or direct to PGND if unused."+      },+      {+        "number": "10",+        "name": "TERM",+        "type": "input",+        "description": "Termination threshold programming input; sets termination current as percentage of programmed charge current IBULK."+      },+      {+        "number": "11",+        "name": "EN2",+        "type": "input",+        "description": "Priority control input between wireless power and wired power with 1.3V high threshold; EN2 low enables wired charging when AD present."+      },+      {+        "number": "12",+        "name": "ILIM",+        "type": "bidirectional",+        "description": "Current programming pin where total resistance RILIM from ILIM to PGND sets charging current from 500mA to 1.5A; KILIM factor is 314 AΩ."+      },+      {+        "number": "13",+        "name": "TS/CTRL",+        "type": "input",+        "description": "Temperature sense input for NTC thermistor monitoring with 2.2V internal bias voltage; connect NTC resistor to PGND or 10-kΩ resistor if NTC not used."+      },+      {+        "number": "14",+        "name": "FOD",+        "type": "input",+        "description": "Foreign object detection power measurement input for WPC v1.2 compatibility with 0-5W received power measurement range."+      },+      {+        "number": "15",+        "name": "COMM2",+        "type": "output",+        "description": "Open-drain output for load modulation communication with primary; connect capacitor from COMM2 to AC2 for capacitive load modulation."+      },+      {+        "number": "16",+        "name": "CLAMP2",+        "type": "output",+        "description": "Open-drain FET output for non-power dissipative overvoltage AC clamp protection; activates when RECT voltage exceeds 15V threshold."+      },+      {+        "number": "17",+        "name": "BOOT2",+        "type": "output",+        "description": "Bootstrap output for driving high-side FETs of synchronous rectifier; connect 10-nF ceramic capacitor from BOOT2 to AC2."+      },+      {+        "number": "18",+        "name": "RECT",+        "type": "output",+        "description": "Filtered rectifier output node; connect ceramic capacitor from 4.7µF to 22µF to PGND depending on power level."+      },+      {+        "number": "19",+        "name": "AC2",+        "type": "input",+        "description": "AC power input from receiver coil with maximum input voltage of 20V and 2A RMS current rating."+      },+      {+        "number": "20",+        "name": "PGND",+        "type": "power_in",+        "description": "Power ground connection for the device."+      },+      {+        "number": "21",+        "name": "EP",+        "type": "passive",+        "description": "Exposed pad (from the footprint; not named in the datasheet pin table)."+      }+    ],+    "provenance": {+      "extractor": "extract_pins 0.2",+      "factory_chain": {+        "factory": "2.0.0",+        "extractor": "extract_pins 0.2",+        "primary_model": "claude-haiku-4-5-20251001",+        "primary_mode": "text",+        "consensus_model": "claude-sonnet-5",+        "consensus": "agreed",+        "guards": "pin_guards 0.1: passed",+        "guard_notes": [+          "exposed pad 21 added from the footprint",+          "dropped thermal pad ['EP'] absent from footprint"+        ],+        "pages_sent": 44,+        "cost_usd": 0.4722,+        "at": "2026-09-22T23:38:38"+      },+      "datasheet": {+        "url": "https://www.ti.com/cn/lit/gpn/bq51050b",+        "pages": 44,+        "sha256": "38293c82dac0e8d1",+        "source_tier": "lcsc"+      },+      "cad": "KiCad official (CC-BY-SA 4.0)",+      "pins": {+        "total": 21,+        "described": 21,+        "cites_pages": true,+        "refuses_to_fabricate": true+      }+    },+    "viewers": {+      "symbol": "viewers/symbol.html",+      "footprint": "viewers/footprint.html"+    }+  },+  "visibility": "public",+  "org": "adom",+  "author": {+    "name": "Ray",+    "email": "[email protected]"+  }+}\ No newline at end of file