← Commit history
page.json+17−14@@ -38,7 +38,7 @@ "number": "1", "name": "VBUS", "type": "power_in",- "description": "Charger input voltage from 3.9 V to 14 V with integrated reverse blocking MOSFET; place 1 \u00b5F ceramic capacitor from VBUS to PGND as close as possible to IC."+ "description": "Charger input voltage from 3.9 V to 14 V with integrated reverse blocking MOSFET; place 1 µF ceramic capacitor from VBUS to PGND as close as possible to IC." }, { "number": "2",@@ -62,19 +62,19 @@ "number": "5", "name": "SCL", "type": "input",- "description": "I2C clock input; connect to logic rail via 10 k\u03a9 pull-up resistor; supports up to 400 kHz fast mode operation."+ "description": "I2C clock input; connect to logic rail via 10 kΩ pull-up resistor; supports up to 400 kHz fast mode operation." }, { "number": "6", "name": "SDA", "type": "bidirectional",- "description": "I2C bidirectional data line; connect to logic rail via 10 k\u03a9 pull-up resistor; slave address is 6BH with R/W bit."+ "description": "I2C bidirectional data line; connect to logic rail via 10 kΩ pull-up resistor; slave address is 6BH with R/W bit." }, { "number": "7", "name": "INT", "type": "output",- "description": "Open-drain interrupt output; sends active-low 256 \u00b5s pulse to host for status and fault reporting; connect via 10 k\u03a9 pull-up resistor."+ "description": "Open-drain interrupt output; sends active-low 256 µs pulse to host for status and fault reporting; connect via 10 kΩ pull-up resistor." }, { "number": "8",@@ -110,25 +110,25 @@ "number": "13", "name": "BAT", "type": "power_in",- "description": "Positive battery terminal connection point operating 2.5 V to 4.6 V; integrated BATFET connects to SYS; requires 10 \u00b5F capacitor placed adjacent to pin."+ "description": "Positive battery terminal connection point operating 2.5 V to 4.6 V; integrated BATFET connects to SYS; requires 10 µF capacitor placed adjacent to pin." }, { "number": "14", "name": "BAT", "type": "power_in",- "description": "Positive battery terminal connection point operating 2.5 V to 4.6 V; integrated BATFET connects to SYS; requires 10 \u00b5F capacitor placed adjacent to pin."+ "description": "Positive battery terminal connection point operating 2.5 V to 4.6 V; integrated BATFET connects to SYS; requires 10 µF capacitor placed adjacent to pin." }, { "number": "15", "name": "SYS", "type": "power_out",- "description": "System power output regulated above minimum system voltage (default 3.5 V) from battery or buck converter; requires 20 \u00b5F output capacitor placed close to IC."+ "description": "System power output regulated above minimum system voltage (default 3.5 V) from battery or buck converter; requires 20 µF output capacitor placed close to IC." }, { "number": "16", "name": "SYS", "type": "power_out",- "description": "System power output regulated above minimum system voltage (default 3.5 V) from battery or buck converter; requires 20 \u00b5F output capacitor placed close to IC."+ "description": "System power output regulated above minimum system voltage (default 3.5 V) from battery or buck converter; requires 20 µF output capacitor placed close to IC." }, { "number": "17",@@ -146,31 +146,31 @@ "number": "19", "name": "SW", "type": "passive",- "description": "Switching node for buck converter LC output filter; internally connected to HSFET source and LSFET drain; requires 0.047 \u00b5F bootstrap capacitor to BTST."+ "description": "Switching node for buck converter LC output filter; internally connected to HSFET source and LSFET drain; requires 0.047 µF bootstrap capacitor to BTST." }, { "number": "20", "name": "SW", "type": "passive",- "description": "Switching node for buck converter LC output filter; internally connected to HSFET source and LSFET drain; requires 0.047 \u00b5F bootstrap capacitor to BTST."+ "description": "Switching node for buck converter LC output filter; internally connected to HSFET source and LSFET drain; requires 0.047 µF bootstrap capacitor to BTST." }, { "number": "21", "name": "BTST", "type": "passive",- "description": "Bootstrap supply node for high-side FET gate driver connected to bootstrap diode anode; requires 0.047 \u00b5F bootstrap capacitor between SW and BTST."+ "description": "Bootstrap supply node for high-side FET gate driver connected to bootstrap diode anode; requires 0.047 µF bootstrap capacitor between SW and BTST." }, { "number": "22", "name": "REGN", "type": "power_out",- "description": "LDO output approximately 5 V for PWM gate drivers and TS pin bias with 50 mA current limit; requires 4.7 \u00b5F (\u226510 V rating) ceramic capacitor to ground."+ "description": "LDO output approximately 5 V for PWM gate drivers and TS pin bias with 50 mA current limit; requires 4.7 µF (≥10 V rating) ceramic capacitor to ground." }, { "number": "23", "name": "PMID", "type": "output",- "description": "Intermediate power node connected to RBFET drain and HSFET drain; requires 1 \u00b5F capacitor to PGND with remaining input capacitance on PMID node."+ "description": "Intermediate power node connected to RBFET drain and HSFET drain; requires 1 µF capacitor to PGND with remaining input capacitance on PMID node." }, { "number": "24",@@ -263,5 +263,8 @@ "docs/bq25896rtwr-datasheet.pdf", "viewers/symbol.html", "viewers/footprint.html"- ]+ ],+ "visibility": {+ "public": true+ } }