← Commit history

bq25896rtwr: component.models_3d pose record per STEP (Z-up, seated z=0, pad-centre origin, identity binding)

Ray ·506cc9a456 · ·parent ae95890
2 files changed +97−17
package.json+55−15
@@ -53,7 +53,7 @@         "number": "1",         "name": "VBUS",         "type": "power_in",-        "description": "Charger input voltage from 3.9 V to 14 V with integrated reverse blocking MOSFET; place 1 \u00b5F ceramic capacitor from VBUS to PGND as close as possible to IC."+        "description": "Charger input voltage from 3.9 V to 14 V with integrated reverse blocking MOSFET; place 1 µF ceramic capacitor from VBUS to PGND as close as possible to IC."       },       {         "number": "2",@@ -77,19 +77,19 @@         "number": "5",         "name": "SCL",         "type": "input",-        "description": "I2C clock input; connect to logic rail via 10 k\u03a9 pull-up resistor; supports up to 400 kHz fast mode operation."+        "description": "I2C clock input; connect to logic rail via 10 kΩ pull-up resistor; supports up to 400 kHz fast mode operation."       },       {         "number": "6",         "name": "SDA",         "type": "bidirectional",-        "description": "I2C bidirectional data line; connect to logic rail via 10 k\u03a9 pull-up resistor; slave address is 6BH with R/W bit."+        "description": "I2C bidirectional data line; connect to logic rail via 10 kΩ pull-up resistor; slave address is 6BH with R/W bit."       },       {         "number": "7",         "name": "INT",         "type": "output",-        "description": "Open-drain interrupt output; sends active-low 256 \u00b5s pulse to host for status and fault reporting; connect via 10 k\u03a9 pull-up resistor."+        "description": "Open-drain interrupt output; sends active-low 256 µs pulse to host for status and fault reporting; connect via 10 kΩ pull-up resistor."       },       {         "number": "8",@@ -125,25 +125,25 @@         "number": "13",         "name": "BAT",         "type": "power_in",-        "description": "Positive battery terminal connection point operating 2.5 V to 4.6 V; integrated BATFET connects to SYS; requires 10 \u00b5F capacitor placed adjacent to pin."+        "description": "Positive battery terminal connection point operating 2.5 V to 4.6 V; integrated BATFET connects to SYS; requires 10 µF capacitor placed adjacent to pin."       },       {         "number": "14",         "name": "BAT",         "type": "power_in",-        "description": "Positive battery terminal connection point operating 2.5 V to 4.6 V; integrated BATFET connects to SYS; requires 10 \u00b5F capacitor placed adjacent to pin."+        "description": "Positive battery terminal connection point operating 2.5 V to 4.6 V; integrated BATFET connects to SYS; requires 10 µF capacitor placed adjacent to pin."       },       {         "number": "15",         "name": "SYS",         "type": "power_out",-        "description": "System power output regulated above minimum system voltage (default 3.5 V) from battery or buck converter; requires 20 \u00b5F output capacitor placed close to IC."+        "description": "System power output regulated above minimum system voltage (default 3.5 V) from battery or buck converter; requires 20 µF output capacitor placed close to IC."       },       {         "number": "16",         "name": "SYS",         "type": "power_out",-        "description": "System power output regulated above minimum system voltage (default 3.5 V) from battery or buck converter; requires 20 \u00b5F output capacitor placed close to IC."+        "description": "System power output regulated above minimum system voltage (default 3.5 V) from battery or buck converter; requires 20 µF output capacitor placed close to IC."       },       {         "number": "17",@@ -161,31 +161,31 @@         "number": "19",         "name": "SW",         "type": "passive",-        "description": "Switching node for buck converter LC output filter; internally connected to HSFET source and LSFET drain; requires 0.047 \u00b5F bootstrap capacitor to BTST."+        "description": "Switching node for buck converter LC output filter; internally connected to HSFET source and LSFET drain; requires 0.047 µF bootstrap capacitor to BTST."       },       {         "number": "20",         "name": "SW",         "type": "passive",-        "description": "Switching node for buck converter LC output filter; internally connected to HSFET source and LSFET drain; requires 0.047 \u00b5F bootstrap capacitor to BTST."+        "description": "Switching node for buck converter LC output filter; internally connected to HSFET source and LSFET drain; requires 0.047 µF bootstrap capacitor to BTST."       },       {         "number": "21",         "name": "BTST",         "type": "passive",-        "description": "Bootstrap supply node for high-side FET gate driver connected to bootstrap diode anode; requires 0.047 \u00b5F bootstrap capacitor between SW and BTST."+        "description": "Bootstrap supply node for high-side FET gate driver connected to bootstrap diode anode; requires 0.047 µF bootstrap capacitor between SW and BTST."       },       {         "number": "22",         "name": "REGN",         "type": "power_out",-        "description": "LDO output approximately 5 V for PWM gate drivers and TS pin bias with 50 mA current limit; requires 4.7 \u00b5F (\u226510 V rating) ceramic capacitor to ground."+        "description": "LDO output approximately 5 V for PWM gate drivers and TS pin bias with 50 mA current limit; requires 4.7 µF (≥10 V rating) ceramic capacitor to ground."       },       {         "number": "23",         "name": "PMID",         "type": "output",-        "description": "Intermediate power node connected to RBFET drain and HSFET drain; requires 1 \u00b5F capacitor to PGND with remaining input capacitance on PMID node."+        "description": "Intermediate power node connected to RBFET drain and HSFET drain; requires 1 µF capacitor to PGND with remaining input capacitance on PMID node."       },       {         "number": "24",@@ -235,6 +235,46 @@     "viewers": {       "symbol": "viewers/symbol.html",       "footprint": "viewers/footprint.html"-    }+    },+    "models_3d": [+      {+        "file": "bq25896rtwr.step",+        "role": "plain",+        "up": "Z",+        "units": "mm",+        "origin": "footprint origin = pad-pattern centre",+        "seat": "z = 0",+        "extents_mm": [+          4.0,+          4.0,+          0.77+        ],+        "zmin_mm": 0.0,+        "centre_offset_mm": 0.0,+        "footprint_binding": "identity",+        "sha256": "096fc110543e6d324c5120c2d38e3dca87a389da9b6fac234f1fe40856295ef4",+        "checked": "2026-10-07",+        "checked_by": "factory/step_pose.py (Z-up, origin, seat, binding)"+      },+      {+        "file": "bq25896rtwr-etched.step",+        "role": "eda",+        "up": "Z",+        "units": "mm",+        "origin": "footprint origin = pad-pattern centre",+        "seat": "z = 0",+        "extents_mm": [+          4.0,+          4.0,+          0.77+        ],+        "zmin_mm": 0.0,+        "centre_offset_mm": 0.0,+        "footprint_binding": "identity",+        "sha256": "f2341f995d18491d89b16efa026a54b19d5c20c5b31348b93b86650339b7e909",+        "checked": "2026-10-07",+        "checked_by": "factory/step_pose.py (Z-up, origin, seat, binding)"+      }+    ]   }-}\ No newline at end of file+}
page.json+42−2
@@ -220,7 +220,47 @@     "viewers": {       "symbol": "viewers/symbol.html",       "footprint": "viewers/footprint.html"-    }+    },+    "models_3d": [+      {+        "file": "bq25896rtwr.step",+        "role": "plain",+        "up": "Z",+        "units": "mm",+        "origin": "footprint origin = pad-pattern centre",+        "seat": "z = 0",+        "extents_mm": [+          4.0,+          4.0,+          0.77+        ],+        "zmin_mm": 0.0,+        "centre_offset_mm": 0.0,+        "footprint_binding": "identity",+        "sha256": "096fc110543e6d324c5120c2d38e3dca87a389da9b6fac234f1fe40856295ef4",+        "checked": "2026-10-07",+        "checked_by": "factory/step_pose.py (Z-up, origin, seat, binding)"+      },+      {+        "file": "bq25896rtwr-etched.step",+        "role": "eda",+        "up": "Z",+        "units": "mm",+        "origin": "footprint origin = pad-pattern centre",+        "seat": "z = 0",+        "extents_mm": [+          4.0,+          4.0,+          0.77+        ],+        "zmin_mm": 0.0,+        "centre_offset_mm": 0.0,+        "footprint_binding": "identity",+        "sha256": "f2341f995d18491d89b16efa026a54b19d5c20c5b31348b93b86650339b7e909",+        "checked": "2026-10-07",+        "checked_by": "factory/step_pose.py (Z-up, origin, seat, binding)"+      }+    ]   },   "metadata": {     "specs": {@@ -268,4 +308,4 @@     "public": true   },   "updated_at": "2026-09-24T18:03:33.725Z"-}\ No newline at end of file+}