component
BQ24232HRGTR
Public Made by Adomby adom
Texas Instruments Battery Management, VQFN-16-EP(3x3). Pinout cross-checked by two models against the datasheet, KiCad symbol/footprint/3D.
main
BQ24232HRGTR
Texas Instruments · Battery Management · VQFN-16-EP(3x3)
BQ24232HRGTR from Texas Instruments, in a VQFN-16-EP(3x3). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | TS | input | External NTC thermistor input that monitors a 10-kΩ NTC in the battery pack; for applications without TS use, connect a 10-kΩ fixed resistor from TS to VSS. |
| 2 | BAT | bidirectional | Charger power stage output and battery voltage sense input; connect to the positive battery terminal and bypass to VSS with a 4.7-μF to 47-μF ceramic capacitor. |
| 3 | BAT | bidirectional | Charger power stage output and battery voltage sense input; connect to the positive battery terminal and bypass to VSS with a 4.7-μF to 47-μF ceramic capacitor. |
| 4 | CE | input | Active-low charge enable; a high level places the charger in standby, a low level enables charging, and CE is internally pulled down with about 285 kΩ and must not be left unconnected. |
| 5 | EN2 | input | Input current limit configuration input that sets the maximum input current and enables USB compliance together with EN1; internally pulled down with about 285 kΩ and must not be left unconnected. |
| 6 | EN1 | input | Input current limit configuration input that sets the maximum input current and enables USB compliance together with EN2; internally pulled down with about 285 kΩ and must not be left unconnected. |
| 7 | PGOOD | output | Open-drain power good output that pulls to VSS when a valid input source is detected; connect through a 1-kΩ to 100-kΩ resistor to the logic rail or use with an LED. |
| 8 | VSS | power_in | Ground connection that must be tied to the thermal pad and to the circuit ground rail. |
| 9 | CHG | output | Open-drain charging status output that pulls to VSS while charging and is high impedance when charging is complete or the charger is disabled. |
| 10 | OUT | output | System supply output that regulates when the input is within range and connects to VBAT when the input is out of range; bypass to VSS with a 4.7-μF to 47-μF ceramic capacitor. |
| 11 | OUT | output | System supply output that regulates when the input is within range and connects to VBAT when the input is out of range; bypass to VSS with a 4.7-μF to 47-μF ceramic capacitor. |
| 12 | ILIM | input | Adjustable input current limit programming input; connect a 3.1-kΩ to 7.8-kΩ resistor from ILIM to VSS to set the maximum input current in EN2=1, EN1=0 mode. |
| 13 | IN | power_in | Input power connection to the DC supply (AC adapter or USB); the '232H operating range is 4.35 V to 10.2 V, the input accepts up to 26 V without damage but operation is suspended, and a 1-μF to 10-μF bypass capacitor to VSS is required. |
| 14 | TMR | input | Timer programming input; connect an 18-kΩ to 72-kΩ resistor from TMR to VSS to set the safety timers, connect to VSS to disable them, or leave unconnected for the 5-hour fast-charge and 30-minute precharge defaults. |
| 15 | ITERM | input | Termination current programming input; connect a 0-Ω to 15-kΩ resistor from ITERM to VSS to set the termination current, or leave unconnected for the internal 10% default threshold. |
| 16 | ISET | bidirectional | Fast-charge current programming input; connect a 1.74-kΩ to 34.8-kΩ resistor from ISET to VSS, since charging is disabled if ISET is left unconnected, and the voltage at ISET reflects the charge current. |
| 17 | EP | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Texas Instruments |
| Package | VQFN-16-EP(3x3) |
| Category | Power Management (PMIC) |
| Pins | 17 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| IN voltage (with respect to VSS) | VI | -0.3 | 28 | V | 4 | ||
| OUT voltage (with respect to VSS) | VO | -0.3 | 7 | V | 4 | ||
| BAT voltage (with respect to VSS) | VBAT | -0.3 | 5 | V | 4 | ||
| Logic pins EN1, EN2, CE, TS, ISET, PGOOD, CHG, ILIM, TMR, TD, ITERM voltage (with respect to VSS) | VI | -0.3 | 7 | V | 4 | ||
| Input current IN | II | 600 | mA | 4 | |||
| Output current continuous OUT | IO | 1700 | mA | 4 | |||
| Output current continuous BAT (discharge mode) | IO | 1700 | mA | Discharge mode | 4 | ||
| Output sink current CHG, PGOOD | 15 | mA | 4 | ||||
| Junction temperature | TJ | -40 | 150 | °C | 4 | ||
| Storage temperature | Tstg | -65 | 150 | °C | 4 | ||
| IN voltage range | VI | 4.35 | 26 | V | 5 | ||
| IN operating voltage range ('232H) | VI | 4.35 | 10.2 | V | 5 | ||
| Input current, IN pin | IIN | 500 | mA | 5 | |||
| Current, OUT pin | IOUT | 1500 | mA | 5 | |||
| Current, BAT pin (discharging) | IBAT | 1500 | mA | Discharging | 5 | ||
| Current, BAT pin (charging) | ICHG | 500 | mA | Charging | 5 | ||
| Junction temperature operating | TJ | -40 | 125 | °C | 5 | ||
| Maximum input current programming resistor | RILIM | 3.1 | 7.8 | kΩ | 5 | ||
| Fast-charge current programming resistor | RISET | 1.74 | 34.8 | kΩ | 5 | ||
| Timer programming resistor | RTMR | 18 | 72 | kΩ | 5 | ||
| Termination programming resistor ('232H) | RITERM | 0 | 15 | kΩ | 5 | ||
| Junction-to-ambient thermal resistance | θJA | 44.5 | °C/W | RGT 16 pins | 5 | ||
| Junction-to-case (top) thermal resistance | θJCtop | 54.2 | °C/W | RGT 16 pins | 5 | ||
| Junction-to-board thermal resistance | θJB | 17.2 | °C/W | RGT 16 pins | 5 | ||
| Junction-to-top characterization parameter | ψJT | 1 | °C/W | RGT 16 pins | 5 | ||
| Junction-to-board characterization parameter | ψJB | 17.1 | °C/W | RGT 16 pins | 5 | ||
| Junction-to-case (bottom) thermal resistance | θJCbot | 3.8 | °C/W | RGT 16 pins | 5 | ||
| Undervoltage lockout | UVLO | 3.2 | 3.3 | 3.4 | V | VIN: 0 V → 4 V | 5 |
| Hysteresis on UVLO | Vhys(UVLO) | 200 | 300 | mV | VIN: 4 V → 0 V | 5 | |
| Input power detection threshold | VIN(DT) | 55 | 95 | 145 | mV | VBAT = 3.6 V, VIN: 3.5 V → 4 V | 5 |
| Input overvoltage protection threshold ('232H) | VOVP | 10.2 | 10.5 | 10.8 | V | VIN: 5 V → 11 V | 5 |
| OUT pin voltage regulation | VO(REG) | 4.4 | 4.5 | 4.6 | V | VIN > VOUT + VDO (IN-OUT) | 6 |
| VIN, VOUT dropout | VDO(IN-OUT) | 150 | 237.5 | mV | VIN = 4.45 V, IIN = 500 mA, VBAT = 4.35 V | 6 | |
| VBAT, VOUT dropout | VDO(BAT-OUT) | 62.5 | mV | IOUT = 500 mA, VIN = 0 V, VBAT > 3 V | 6 | ||
| Maximum input current (EN1 = LO, EN2 = LO) | IINmax | 90 | 95 | 100 | mA | EN1 = LO, EN2 = LO | 6 |
| Maximum input current (EN1 = HI, EN2 = LO) | IINmax | 450 | 475 | 500 | mA | EN1 = HI, EN2 = LO | 6 |
| Maximum input current factor | KILIM | 1380 | 1530 | 1680 | AΩ | ILIM = 200 mA to 500 mA | 6 |
| Programmable input current limit range | IINmax | 200 | 500 | mA | EN2 = HI, EN1 = LO, RILIM = 3.1 kΩ to 7.8 kΩ | 6 | |
| Input voltage threshold when input current is reduced | VIN-DPM | 4.35 | 4.5 | 4.63 | V | EN2 = LO, EN1 = X | 6 |
| Output short-circuit detection threshold, power-on | VO(SC1) | 0.8 | 0.9 | 1 | V | VIN > UVLO and VIN > VBAT + VIN(DT) | 6 |
| Output short-circuit detection threshold, supplement mode | VO(SC2) | 200 | 250 | 300 | mV | VBAT, VOUT > VO(SC2) indicates short circuit; VIN > UVLO and VIN > VBAT + VIN(DT) | 6 |
| Source current for BAT pin short-circuit detection | IBAT(SC) | 4 | 7.5 | 11 | mA | VBAT = 1.5 V | 7 |
| BAT pin short-circuit detection threshold | VBAT(SC) | 1.6 | 1.8 | 2 | V | VBAT rising | 7 |
| Battery charge voltage | VBAT(REG) | 4.306 | 4.35 | 4.394 | V | 7 | |
| Precharge to fast-charge transition threshold | VLOWV | 2.9 | 3 | 3.1 | V | VIN > UVLO and VIN > VBAT + VIN(DT) | 7 |
| Battery fast-charge current range | ICHG | 25 | 500 | mA | VBAT(REG) > VBAT > VLOWV, VIN = 5 V, CE = LO, EN1 = LO, EN2 = HI | 7 | |
| Fast-charge current factor | KISET | 797 | 870 | 975 | AΩ | 25 mA ≤ ICHG ≤ 500 mA | 7 |
| Precharge current factor | KPRECHG | 70 | 88 | 106 | AΩ | 2.5 mA ≤ IPRECHG ≤ 50 mA | 7 |
| Termination comparator threshold, internally set (EN1,EN2 ≠ LO,LO) | ITERM | 0.09 | 0.1 | 0.11 | x ICHG | CE = LO, (EN1,EN2) ≠ (LO,LO), VBAT > VRCH, t < tMAXCH, VIN = 5 V, DPM loop and thermal loop not active | 7 |
| Termination comparator threshold, internally set ((EN1,EN2) = LO,LO) | ITERM | 0.027 | 0.033 | 0.04 | x ICHG | CE = LO, (EN1,EN2) = (LO,LO), VBAT > VRCH, t < tMAXCH, VIN = 5 V, DPM loop and thermal loop not active | 7 |
| K factor for termination detection threshold (externally set, bq24232H) | KITERM | 0.024 | 0.03 | 0.036 | A | CE = LO, (EN1,EN2) ≠ (LO,LO), VBAT > VRCH, t < tMAXCH, VIN = 5 V, DPM loop and thermal loop not active | 7 |
| K factor for termination detection threshold (externally set, bq24232H, (EN1,EN2) = LO,LO) | KITERM | 0.009 | 0.01 | 0.011 | A | CE = LO, (EN1,EN2) = (LO,LO), VBAT > VRCH, t < tMAXCH, VIN = 5 V, DPM loop and thermal loop not active | 7 |
| Current for external termination-setting resistor | IBIAS(ITERM) | 72 | 75 | 78 | μA | 7 | |
| Recharge detection threshold | VRCH | -140 | -100 | -60 | mV | VIN > UVLO and VIN > VBAT + VIN(DT); relative to VBAT(REG) | 7 |
| Sink current for battery detection | IBAT(DET) | 5 | 7.5 | 10 | mA | VBAT = 2.5 V | 7 |
| Precharge safety timer value | tPRECHG | 1440 | 1800 | 2160 | s | TMR = floating | 7 |
| Charge safety timer value | tMAXCHG | 14400 | 18000 | 21600 | s | TMR = floating | 7 |
| Timer factor | KTMR | 30 | 40 | 50 | s/kΩ | 7 | |
| NTC bias current | INTC | 72 | 75 | 78 | μA | VIN > UVLO and VIN > VBAT + VIN(DT) | 8 |
| High-temperature trip point | VHOT | 270 | 300 | 330 | mV | Battery charging, VTS falling | 8 |
| Low-temperature trip point | VCOLD | 2000 | 2100 | 2200 | mV | Battery charging, VTS rising | 8 |
| Deglitch time, pack temperature fault detection | tDGL(TS) | 50 | ms | Battery charging, VTS falling | 8 | ||
| Temperature regulation limit | TJ(REG) | 125 | °C | 8 | |||
| Thermal shutdown temperature | TJ(OFF) | 155 | °C | TJ rising | 8 | ||
| Thermal shutdown hysteresis | TJ(OFF-HYS) | 20 | °C | 8 | |||
| Logic LOW input voltage | VIL | 0 | 0.4 | V | Logic inputs EN1, EN2, CE, TD | 8 | |
| Logic HIGH input voltage | VIH | 1.4 | 6 | V | Logic inputs EN1, EN2, CE, TD | 8 | |
| Input sink current | IIL | 1 | μA | VIL = 0 V | 8 | ||
| Input source current | IIH | 10 | μA | VIH = 1.4 V | 8 | ||
| Output LOW voltage | VOL | 0.4 | V | ISINK = 5 mA; PGOOD, CHG | 8 | ||
| Sleep current into BAT pin | IBAT(PDWN) | 6.5 | μA | CE = LO or HI, input power not detected, no load on OUT pin, TJ = 85°C | 5 | ||
| Standby current into IN pin (VIN = 10 V) | IIN(STDBY) | 200 | μA | EN1= HI, EN2=HI, VIN = 10 V, TJ=85°C | 6 | ||
| Active supply current, IN pin | ICC | 1.5 | mA | CE = LO, VIN = 6 V, no load on OUT pin, VBAT > VBAT(REG), (EN1, EN2) ≠ (HI, HI) | 6 | ||
| Deglitch time, supplement mode short circuit | tDGL(SC2) | 250 | μs | 6 | |||
| Recovery time, supplement mode short circuit | tREC(SC2) | 60 | ms | 6 | |||
| Input overvoltage blanking time | tDGL(OVP) | 50 | μs | 5 | |||
| Hysteresis on OVP ('232H) | Vhys(OVP) | 175 | mV | VIN: 11 V → 5 V | 5 | ||
| Hysteresis on VIN(DT) | Vhys(INDT) | 20 | mV | VBAT = 3.6 V, VIN: 4 V → 3.5 V | 5 |
CAD (KiCad official)
- Symbol:
BQ24232HRGTR - Footprint:
Package_DFN_QFN:QFN-16-1EP_3x3mm_P0.5mm_EP1.7x1.7mm - 3D model: VQFN-16-EP(3x3) (KiCad packages3D, STEP)
- 3D model files:
bq24232hrgtr-etched.step/bq24232hrgtr-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);bq24232hrgtr.step/bq24232hrgtr.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Texas Instruments datasheet (42 pp, sha256
b908e6a901d9055d, retrieved 2026-11-05, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).
# BQ24232HRGTR
**Texas Instruments** · Battery Management · VQFN-16-EP(3x3)
BQ24232HRGTR from Texas Instruments, in a VQFN-16-EP(3x3). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
## Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | TS | input | External NTC thermistor input that monitors a 10-kΩ NTC in the battery pack; for applications without TS use, connect a 10-kΩ fixed resistor from TS to VSS. |
| 2 | BAT | bidirectional | Charger power stage output and battery voltage sense input; connect to the positive battery terminal and bypass to VSS with a 4.7-μF to 47-μF ceramic capacitor. |
| 3 | BAT | bidirectional | Charger power stage output and battery voltage sense input; connect to the positive battery terminal and bypass to VSS with a 4.7-μF to 47-μF ceramic capacitor. |
| 4 | CE | input | Active-low charge enable; a high level places the charger in standby, a low level enables charging, and CE is internally pulled down with about 285 kΩ and must not be left unconnected. |
| 5 | EN2 | input | Input current limit configuration input that sets the maximum input current and enables USB compliance together with EN1; internally pulled down with about 285 kΩ and must not be left unconnected. |
| 6 | EN1 | input | Input current limit configuration input that sets the maximum input current and enables USB compliance together with EN2; internally pulled down with about 285 kΩ and must not be left unconnected. |
| 7 | PGOOD | output | Open-drain power good output that pulls to VSS when a valid input source is detected; connect through a 1-kΩ to 100-kΩ resistor to the logic rail or use with an LED. |
| 8 | VSS | power_in | Ground connection that must be tied to the thermal pad and to the circuit ground rail. |
| 9 | CHG | output | Open-drain charging status output that pulls to VSS while charging and is high impedance when charging is complete or the charger is disabled. |
| 10 | OUT | output | System supply output that regulates when the input is within range and connects to VBAT when the input is out of range; bypass to VSS with a 4.7-μF to 47-μF ceramic capacitor. |
| 11 | OUT | output | System supply output that regulates when the input is within range and connects to VBAT when the input is out of range; bypass to VSS with a 4.7-μF to 47-μF ceramic capacitor. |
| 12 | ILIM | input | Adjustable input current limit programming input; connect a 3.1-kΩ to 7.8-kΩ resistor from ILIM to VSS to set the maximum input current in EN2=1, EN1=0 mode. |
| 13 | IN | power_in | Input power connection to the DC supply (AC adapter or USB); the '232H operating range is 4.35 V to 10.2 V, the input accepts up to 26 V without damage but operation is suspended, and a 1-μF to 10-μF bypass capacitor to VSS is required. |
| 14 | TMR | input | Timer programming input; connect an 18-kΩ to 72-kΩ resistor from TMR to VSS to set the safety timers, connect to VSS to disable them, or leave unconnected for the 5-hour fast-charge and 30-minute precharge defaults. |
| 15 | ITERM | input | Termination current programming input; connect a 0-Ω to 15-kΩ resistor from ITERM to VSS to set the termination current, or leave unconnected for the internal 10% default threshold. |
| 16 | ISET | bidirectional | Fast-charge current programming input; connect a 1.74-kΩ to 34.8-kΩ resistor from ISET to VSS, since charging is disabled if ISET is left unconnected, and the voltage at ISET reflects the charge current. |
| 17 | EP | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |
## Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Texas Instruments |
| Package | VQFN-16-EP(3x3) |
| Category | Power Management (PMIC) |
| Pins | 17 |
## Electrical characteristics
Limits as printed in the datasheet (page.json `metadata.characteristics` carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| IN voltage (with respect to VSS) | VI | -0.3 | | 28 | V | | 4 |
| OUT voltage (with respect to VSS) | VO | -0.3 | | 7 | V | | 4 |
| BAT voltage (with respect to VSS) | VBAT | -0.3 | | 5 | V | | 4 |
| Logic pins EN1, EN2, CE, TS, ISET, PGOOD, CHG, ILIM, TMR, TD, ITERM voltage (with respect to VSS) | VI | -0.3 | | 7 | V | | 4 |
| Input current IN | II | | | 600 | mA | | 4 |
| Output current continuous OUT | IO | | | 1700 | mA | | 4 |
| Output current continuous BAT (discharge mode) | IO | | | 1700 | mA | Discharge mode | 4 |
| Output sink current CHG, PGOOD | | | | 15 | mA | | 4 |
| Junction temperature | TJ | -40 | | 150 | °C | | 4 |
| Storage temperature | Tstg | -65 | | 150 | °C | | 4 |
| IN voltage range | VI | 4.35 | | 26 | V | | 5 |
| IN operating voltage range ('232H) | VI | 4.35 | | 10.2 | V | | 5 |
| Input current, IN pin | IIN | | | 500 | mA | | 5 |
| Current, OUT pin | IOUT | | | 1500 | mA | | 5 |
| Current, BAT pin (discharging) | IBAT | | | 1500 | mA | Discharging | 5 |
| Current, BAT pin (charging) | ICHG | | | 500 | mA | Charging | 5 |
| Junction temperature operating | TJ | -40 | | 125 | °C | | 5 |
| Maximum input current programming resistor | RILIM | 3.1 | | 7.8 | kΩ | | 5 |
| Fast-charge current programming resistor | RISET | 1.74 | | 34.8 | kΩ | | 5 |
| Timer programming resistor | RTMR | 18 | | 72 | kΩ | | 5 |
| Termination programming resistor ('232H) | RITERM | 0 | | 15 | kΩ | | 5 |
| Junction-to-ambient thermal resistance | θJA | | 44.5 | | °C/W | RGT 16 pins | 5 |
| Junction-to-case (top) thermal resistance | θJCtop | | 54.2 | | °C/W | RGT 16 pins | 5 |
| Junction-to-board thermal resistance | θJB | | 17.2 | | °C/W | RGT 16 pins | 5 |
| Junction-to-top characterization parameter | ψJT | | 1 | | °C/W | RGT 16 pins | 5 |
| Junction-to-board characterization parameter | ψJB | | 17.1 | | °C/W | RGT 16 pins | 5 |
| Junction-to-case (bottom) thermal resistance | θJCbot | | 3.8 | | °C/W | RGT 16 pins | 5 |
| Undervoltage lockout | UVLO | 3.2 | 3.3 | 3.4 | V | VIN: 0 V → 4 V | 5 |
| Hysteresis on UVLO | Vhys(UVLO) | 200 | 300 | | mV | VIN: 4 V → 0 V | 5 |
| Input power detection threshold | VIN(DT) | 55 | 95 | 145 | mV | VBAT = 3.6 V, VIN: 3.5 V → 4 V | 5 |
| Input overvoltage protection threshold ('232H) | VOVP | 10.2 | 10.5 | 10.8 | V | VIN: 5 V → 11 V | 5 |
| OUT pin voltage regulation | VO(REG) | 4.4 | 4.5 | 4.6 | V | VIN > VOUT + VDO (IN-OUT) | 6 |
| VIN, VOUT dropout | VDO(IN-OUT) | | 150 | 237.5 | mV | VIN = 4.45 V, IIN = 500 mA, VBAT = 4.35 V | 6 |
| VBAT, VOUT dropout | VDO(BAT-OUT) | | | 62.5 | mV | IOUT = 500 mA, VIN = 0 V, VBAT > 3 V | 6 |
| Maximum input current (EN1 = LO, EN2 = LO) | IINmax | 90 | 95 | 100 | mA | EN1 = LO, EN2 = LO | 6 |
| Maximum input current (EN1 = HI, EN2 = LO) | IINmax | 450 | 475 | 500 | mA | EN1 = HI, EN2 = LO | 6 |
| Maximum input current factor | KILIM | 1380 | 1530 | 1680 | AΩ | ILIM = 200 mA to 500 mA | 6 |
| Programmable input current limit range | IINmax | 200 | | 500 | mA | EN2 = HI, EN1 = LO, RILIM = 3.1 kΩ to 7.8 kΩ | 6 |
| Input voltage threshold when input current is reduced | VIN-DPM | 4.35 | 4.5 | 4.63 | V | EN2 = LO, EN1 = X | 6 |
| Output short-circuit detection threshold, power-on | VO(SC1) | 0.8 | 0.9 | 1 | V | VIN > UVLO and VIN > VBAT + VIN(DT) | 6 |
| Output short-circuit detection threshold, supplement mode | VO(SC2) | 200 | 250 | 300 | mV | VBAT, VOUT > VO(SC2) indicates short circuit; VIN > UVLO and VIN > VBAT + VIN(DT) | 6 |
| Source current for BAT pin short-circuit detection | IBAT(SC) | 4 | 7.5 | 11 | mA | VBAT = 1.5 V | 7 |
| BAT pin short-circuit detection threshold | VBAT(SC) | 1.6 | 1.8 | 2 | V | VBAT rising | 7 |
| Battery charge voltage | VBAT(REG) | 4.306 | 4.35 | 4.394 | V | | 7 |
| Precharge to fast-charge transition threshold | VLOWV | 2.9 | 3 | 3.1 | V | VIN > UVLO and VIN > VBAT + VIN(DT) | 7 |
| Battery fast-charge current range | ICHG | 25 | | 500 | mA | VBAT(REG) > VBAT > VLOWV, VIN = 5 V, CE = LO, EN1 = LO, EN2 = HI | 7 |
| Fast-charge current factor | KISET | 797 | 870 | 975 | AΩ | 25 mA ≤ ICHG ≤ 500 mA | 7 |
| Precharge current factor | KPRECHG | 70 | 88 | 106 | AΩ | 2.5 mA ≤ IPRECHG ≤ 50 mA | 7 |
| Termination comparator threshold, internally set (EN1,EN2 ≠ LO,LO) | ITERM | 0.09 | 0.1 | 0.11 | x ICHG | CE = LO, (EN1,EN2) ≠ (LO,LO), VBAT > VRCH, t < tMAXCH, VIN = 5 V, DPM loop and thermal loop not active | 7 |
| Termination comparator threshold, internally set ((EN1,EN2) = LO,LO) | ITERM | 0.027 | 0.033 | 0.04 | x ICHG | CE = LO, (EN1,EN2) = (LO,LO), VBAT > VRCH, t < tMAXCH, VIN = 5 V, DPM loop and thermal loop not active | 7 |
| K factor for termination detection threshold (externally set, bq24232H) | KITERM | 0.024 | 0.03 | 0.036 | A | CE = LO, (EN1,EN2) ≠ (LO,LO), VBAT > VRCH, t < tMAXCH, VIN = 5 V, DPM loop and thermal loop not active | 7 |
| K factor for termination detection threshold (externally set, bq24232H, (EN1,EN2) = LO,LO) | KITERM | 0.009 | 0.01 | 0.011 | A | CE = LO, (EN1,EN2) = (LO,LO), VBAT > VRCH, t < tMAXCH, VIN = 5 V, DPM loop and thermal loop not active | 7 |
| Current for external termination-setting resistor | IBIAS(ITERM) | 72 | 75 | 78 | μA | | 7 |
| Recharge detection threshold | VRCH | -140 | -100 | -60 | mV | VIN > UVLO and VIN > VBAT + VIN(DT); relative to VBAT(REG) | 7 |
| Sink current for battery detection | IBAT(DET) | 5 | 7.5 | 10 | mA | VBAT = 2.5 V | 7 |
| Precharge safety timer value | tPRECHG | 1440 | 1800 | 2160 | s | TMR = floating | 7 |
| Charge safety timer value | tMAXCHG | 14400 | 18000 | 21600 | s | TMR = floating | 7 |
| Timer factor | KTMR | 30 | 40 | 50 | s/kΩ | | 7 |
| NTC bias current | INTC | 72 | 75 | 78 | μA | VIN > UVLO and VIN > VBAT + VIN(DT) | 8 |
| High-temperature trip point | VHOT | 270 | 300 | 330 | mV | Battery charging, VTS falling | 8 |
| Low-temperature trip point | VCOLD | 2000 | 2100 | 2200 | mV | Battery charging, VTS rising | 8 |
| Deglitch time, pack temperature fault detection | tDGL(TS) | | 50 | | ms | Battery charging, VTS falling | 8 |
| Temperature regulation limit | TJ(REG) | | 125 | | °C | | 8 |
| Thermal shutdown temperature | TJ(OFF) | | 155 | | °C | TJ rising | 8 |
| Thermal shutdown hysteresis | TJ(OFF-HYS) | | 20 | | °C | | 8 |
| Logic LOW input voltage | VIL | 0 | | 0.4 | V | Logic inputs EN1, EN2, CE, TD | 8 |
| Logic HIGH input voltage | VIH | 1.4 | | 6 | V | Logic inputs EN1, EN2, CE, TD | 8 |
| Input sink current | IIL | | | 1 | μA | VIL = 0 V | 8 |
| Input source current | IIH | | | 10 | μA | VIH = 1.4 V | 8 |
| Output LOW voltage | VOL | | | 0.4 | V | ISINK = 5 mA; PGOOD, CHG | 8 |
| Sleep current into BAT pin | IBAT(PDWN) | | | 6.5 | μA | CE = LO or HI, input power not detected, no load on OUT pin, TJ = 85°C | 5 |
| Standby current into IN pin (VIN = 10 V) | IIN(STDBY) | | | 200 | μA | EN1= HI, EN2=HI, VIN = 10 V, TJ=85°C | 6 |
| Active supply current, IN pin | ICC | | | 1.5 | mA | CE = LO, VIN = 6 V, no load on OUT pin, VBAT > VBAT(REG), (EN1, EN2) ≠ (HI, HI) | 6 |
| Deglitch time, supplement mode short circuit | tDGL(SC2) | | 250 | | μs | | 6 |
| Recovery time, supplement mode short circuit | tREC(SC2) | | 60 | | ms | | 6 |
| Input overvoltage blanking time | tDGL(OVP) | | 50 | | μs | | 5 |
| Hysteresis on OVP ('232H) | Vhys(OVP) | | 175 | | mV | VIN: 11 V → 5 V | 5 |
| Hysteresis on VIN(DT) | Vhys(INDT) | | 20 | | mV | VBAT = 3.6 V, VIN: 4 V → 3.5 V | 5 |
## CAD (KiCad official)
- Symbol: `BQ24232HRGTR`
- Footprint: `Package_DFN_QFN:QFN-16-1EP_3x3mm_P0.5mm_EP1.7x1.7mm`
- 3D model: VQFN-16-EP(3x3) (KiCad packages3D, STEP)
- 3D model files: `bq24232hrgtr-etched.step` / `bq24232hrgtr-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `bq24232hrgtr.step` / `bq24232hrgtr.glb` are the bare package body.
## Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- **Datasheet:** [Texas Instruments datasheet](https://www.ti.com/lit/ds/symlink/bq24232h.pdf) (42 pp, sha256 `b908e6a901d9055d`, retrieved 2026-11-05, tier: manufacturer)
- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.3`, primary `claude-haiku-5-5` (text), consensus `claude-sonnet-5-5` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
- **CAD:** KiCad official libraries (CC-BY-SA 4.0).
[Datasheet PDF](docs/bq24232hrgtr-datasheet.pdf)