component
BQ24196RGER
Public Made by Adomby adom
Texas Instruments Battery Management, VQFN-24-EP(4x4). Pinout cross-checked by two models against the datasheet, KiCad symbol/footprint/3D.
3D Model
Open in new tab ↗
Loads on click. Unloads only if this page sits in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads on click. Unloads only if this page sits in the background.
PCB Footprint
Open full view ↗Loads on click. Unloads only if this page sits in the background.
Datasheet
Open in new tab ↗Loads on click. Unloads only if this page sits in the background.
README
markdownBQ24196RGER
Texas Instruments · Battery Management · VQFN-24-EP(4x4)
BQ24196RGER from Texas Instruments, in a VQFN-24-EP(4x4). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | VBUS | power_in | Charger Input Voltage with internal n-channel reverse block MOSFET (RBFET) connected between VBUS source and PMID; place 1-µF ceramic capacitor from VBUS to PGND close to IC. |
| 2 | PSEL | input | Power source selection input; High indicates USB host source and Low indicates adapter source. |
| 3 | PG | output | Open drain active low power good indicator; connect to pull-up rail via 10-kΩ resistor; LOW indicates good input source when input voltage between UVLO and ACOV, above SLEEP mode threshold, and current limit above 30 mA. |
| 4 | STAT | output | Open drain charge status output to indicate charger operation; connect to pull-up rail via 10-kΩ resistor; LOW indicates charge in progress, HIGH indicates charge complete or disabled, blinking at 1 Hz for fault conditions. |
| 5 | SCL | input | I2C Interface clock; connect SCL to logic rail through 10-kΩ resistor; supports standard mode up to 100 kbits and fast mode up to 400 kbits. |
| 6 | SDA | bidirectional | I2C Interface data; connect SDA to logic rail through 10-kΩ resistor; open drain pin used for bidirectional communication. |
| 7 | INT | output | Open-drain Interrupt Output; connect INT to logic rail via 10-kΩ resistor; sends active low 256-us pulse to host to report charger device status and fault conditions. |
| 8 | OTG | input | USB current limit selection pin during buck mode and active high enable pin during boost mode; in buck mode with USB host (PSEL=High), when OTG=High, IIN limit=500 mA, when OTG=Low, IIN limit=100 mA; boost mode activated when REG01[5:4]=10 and OTG=High. |
| 9 | CE | input | Active low Charge Enable pin; battery charging is enabled when REG01[5:4]=01 and CE pin=Low; CE pin must be pulled high or low. |
| 10 | ILIM | input | Input current limit selection pin; sets maximum input current limit by regulating ILIM voltage at 1V using resistor from ILIM pin to ground; INMAX=(1V/RILIM)×530; actual input current limit is lower value set by ILIM and I2C REG00[2:0]; minimum input current is 500 mA. |
| 11 | TS1 | input | Temperature qualification voltage input #1; connect negative temperature coefficient thermistor; program temperature window with resistor divider from REGN to TS1 to GND; charge suspends when TS pin is out of range; recommend 103AT-2 thermistor. |
| 12 | TS2 | input | Temperature qualification voltage input #2; connect negative temperature coefficient thermistor; program temperature window with resistor divider from REGN to TS2 to GND; charge suspends when TS pin is out of range; TS1 and TS2 can be connected together for single thermistor application. |
| 13 | BAT | power_in | Battery connection point to positive terminal of battery pack; internal BATFET connected between BAT and SYS; connect 10 µF capacitor closely to BAT pin. |
| 14 | BAT | power_in | Battery connection point to positive terminal of battery pack; duplicate pin for current distribution; internal BATFET connected between BAT and SYS. |
| 15 | SYS | power_in | System connection point; internal BATFET connected between BAT and SYS; when battery falls below minimum system voltage, switch-mode converter keeps SYS above minimum system voltage setting. |
| 16 | SYS | power_in | System connection point; duplicate pin for current distribution; internal BATFET connected between BAT and SYS. |
| 17 | PGND | power_in | Power ground connection for high-current power converter node; internally connected to source of n-channel LSFET; connect directly to ground connection of input and output capacitors; single point connection recommended between power PGND and analog GND near IC. |
| 18 | PGND | power_in | Power ground connection; duplicate pin for current distribution; internally connected to source of n-channel LSFET. |
| 19 | SW | output | Switching node connecting to output inductor; internally connected to source of n-channel HSFET and drain of n-channel LSFET; connect 0.047-µF bootstrap capacitor from SW to BTST. |
| 20 | SW | output | Switching node; duplicate pin for current distribution; internally connected to source of n-channel HSFET and drain of n-channel LSFET. |
| 21 | BTST | power_in | PWM high side driver positive supply; internally connected to anode of bootstrap diode; connect 0.047-µF bootstrap capacitor from SW to BTST. |
| 22 | REGN | power_in | PWM low side driver positive supply output; internally connected to cathode of bootstrap diode; connect 4.7-µF (10-V rating) ceramic capacitor from REGN to analog GND close to IC; also serves as bias rail for TS1 and TS2 pins. |
| 23 | PMID | output | Connected to drain of reverse blocking MOSFET and drain of HSFET; given total input capacitance, connect 1-µF capacitor on VBUS to PGND and rest on PMID to PGND. |
| 24 | VBUS | power_in | Charger Input Voltage; duplicate pin for current distribution; internal n-channel reverse block MOSFET (RBFET) connected to VBUS. |
| 25 | EP | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Texas Instruments |
| Package | VQFN-24-EP(4x4) |
| Category | Power Management (PMIC) |
| Pins | 25 |
CAD (KiCad official)
- Symbol:
BQ24196RGER - Footprint:
Package_DFN_QFN:QFN-24-1EP_4x4mm_P0.5mm_EP2.6x2.6mm - 3D model: VQFN-24-EP(4x4) (KiCad packages3D, STEP)
- 3D model files:
bq24196rger-etched.step/bq24196rger-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);bq24196rger.step/bq24196rger.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Texas Instruments datasheet (51 pp, sha256
e6d0c7f6f4a1a193, retrieved 2026-09-24, tier: lcsc) - Datasheet language: Chinese. Pin names, descriptions, and specs on this page were extracted and translated to English by ds2sf; the linked PDF is the manufacturer original.
- Extractor: parts-factory
2.0.0/extract_pins 0.2, primaryclaude-haiku-4-5-20251001(text), consensusclaude-sonnet-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).