master
Ray
Publish 0.1.0
2586250
BMP581
Bosch Sensortec · Pressure Sensors · LGA-10(2x2)
BMP581 from Bosch Sensortec, in a LGA-10(2x2). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model). The symbol is generated from that pin table, the footprint is an Adom_Gen land derived from the manufacturer drawing, and the 3D model is generated to fit it.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | VDDIO | power_in | Digital interface supply VDDIO, connected to the host interface supply. |
| 2 | SCK | input | Serial clock input, used in both SPI 4-wire and SPI 3-wire modes. |
| 3 | VSS | power_in | Ground; all VSS pins must be connected to GND. |
| 4 | SDI | bidirectional | Serial data input in SPI 4-wire mode and bidirectional SDI/SDO data pad in SPI 3-wire mode; it must be tied to low or high and not left floating. |
| 5 | SDO | bidirectional | Serial data output in SPI 4-wire mode; in SPI 3-wire mode it must be left floating (DNC). |
| 6 | CSB | input | Chip select input, active low. |
| 7 | INT | output | Interrupt output to the host INT input; it may be connected to GND or left unconnected only with INT_CONFIG.int_en disabled or the recommended settings. |
| 8 | VSS | power_in | Ground; all VSS pins must be connected to GND. |
| 9 | VSS | power_in | Ground; all VSS pins must be connected to GND. |
| 10 | VDD | power_in | Analog supply VDD for the sensor. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Bosch Sensortec |
| Package | LGA-10(2x2) |
| Category | Sensors |
| Pins | 10 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Relative pressure accuracy | Ap_rel | -0.4 | 0.4 | Pa | 900, 1100 hPa, 25 °C, 1 kPa steps | 8 | |
| Absolute pressure accuracy | Ap_abs | -30 | 30 | Pa | 300, 1100 hPa, -5, 65 °C, including TCO | 8 | |
| Absolute accuracy pressure (full range) | Ap_abs_full_range | -75 | 75 | Pa | 300, 1100 hPa, -40, 85 °C, incl. solder drift, TCO after qualification | 9 | |
| Offset temperature coefficient | TCO | -0.5 | 0.5 | Pa/K | 300, 1100 hPa, -5, 65 °C, 10 K steps | 9 | |
| Long term drift | ∆Pstab_long | -10 | 10 | Pa | Drift during 1 year | 9 | |
| Short term drift | ∆Pstab_short | -1.5 | 1.5 | Pa | Drift during 24 h at constant pressure and temperature | 9 | |
| Solder drift | -30 | 30 | Pa | 5x reflow soldering after storage in standard conditions (25 °C / 100 kPa) | 9 | ||
| Absolute accuracy temperature | At_abs | -0.5 | 0.5 | K | -5 .. 55°C | 10 | |
| Absolute accuracy temperature full range | At_abs_full | -0.5 | 0.5 | K | -40 .. 85°C | 10 | |
| Pressure noise low power | Vp_low_power | 0.78 | 0.95 | PaRMS | OSR set to lowest power | 8 | |
| Pressure noise high resolution | Vp_hi_res | 0.21 | 0.25 | PaRMS | OSR set to high resolution | 8 | |
| Power supply voltage | VDD | 1.71 | 3.6 | V | 10 | ||
| Power supply voltage I/Os | VDDIO | 1.08 | 3.6 | V | 10 | ||
| Supply ramp time | t_VDDramp & t_VDDIOramp | 0.01 | 10 | ms | 10% to 90% of target voltage | 10 | |
| Operational temperature range | TOP_full | -40 | 85 | °C | 10 | ||
| ODR accuracy | -10 | 10 | % | -40..85°C | 10 | ||
| Power-up time | t_powup | 2 | ms | Time to first communication after both VDD > VDDmin and VDDIO > VDDIOmin | 10 | ||
| Start-up time from STANDBY | t_startup | 3 | ms | Time from mode change to start of measurement | 11 | ||
| Start-up time from DEEP STANDBY | tstartup_deep | 4 | ms | Time from mode change to start of measurement | 11 | ||
| Re-configuration time | treconf | 3 | ms | Time from configuration change in NORMAL or CONTINUOUS mode to start of first measurement | 11 | ||
| Re-configuration time (deep) | treconf_deep | 4 | ms | Time from configuration change in NORMAL or CONTINUOUS mode to start of first measurement | 11 | ||
| Time to standby | tstandby | 2.5 | ms | Time from any mode to STANDBY | 11 | ||
| Soft reset duration | tsoft_res | 2 | ms | Time from trigger of soft reset until device ready | 11 | ||
| I3C interface clock | fi3C | 0.1 | 12.5 | 12.9 | MHz | @ VDDIO > 1.62 V - Normal Mode & Fast Mode @ Cbus < 550pF - Fast Mode + @Cbus > 100pF | 11 |
| SPI interface clock | fspi | 12 | MHz | @ VDDIO ≥ 1.62 V, Cbus ≤ 80 pF 4-wire/ 3-wire; modes 0 and 3 | 11 | ||
| SPI interface clock low voltage | fspi_lowv | 7 | MHz | @ VDDIO ≤ 1.62 V, Cbus ≤ 40 pF 4-wire/ 3-wire; modes 0 and 3 | 11 | ||
| Peak current | ipeak | 260 | μA | maximum DC current | 12 | ||
| Deep Standby current | 0.55 | μA | 25 °C and VDDIO=VDD=1.8 V | 12 | |||
| Deep Standby current | 1.5 | μA | 55 °C and VDDIO=VDD=1.8 V | 12 | |||
| Standby current | 1 | μA | 25 °C and VDDIO=VDD=1.8 V | 12 | |||
| Standby current | 3.5 | μA | 55 °C and VDDIO=VDD=1.8 V | 12 | |||
| Current consumption low power mode | 1.3 | μA | OSR set to lowest power, Low Power Mode ODR=1 Hz 25 °C | 12 | |||
| INT pulse length | tint_pulse | 90 | 105 | 121 | μs | Pulse length in pulsed mode | 12 |
| INT minimum deassert time | tint_deassert | 90 | 105 | 121 | μs | Minimum time between INT pin assert | 12 |
| Maximum output rate (ODR) | 489 | Hz | in CONTINUOUS mode, pressure and temperature measured | 12 | |||
| Output data rate (ODR) range | 0.125 | 240 | Hz | in NORMAL mode | 12 | ||
| Pull-up resistance at CSB pin | RPU_CSB | 74 | 100 | 131 | kOhm | I2C mode, relevant for interface mode selection | 13 |
| Storage temperature | -40 | 125 | °C | ≤ 65 % r.h. Standard conditions: + 25°C and 40% r.h. | 13 | ||
| Supply voltage | VDD | -0.3 | 4.3 | V | 13 | ||
| Max voltage at I/O pins | VSSIO | -0.3 | V | Max voltage at I/O pins, VSSIO-0.3 V to VDDIO + 0.3 V | 13 |
CAD (Adom-generated)
- Symbol:
BMP581 - Footprint:
Adom_Gen:BOSCH_SENSORTECH_BMP581_1a03d8 - 3D model: generated to fit the land (STEP)
- 3D model files:
bmp581-etched.step/bmp581-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);bmp581.step/bmp581.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Bosch Sensortec datasheet (75 pp, sha256
ddcf4202c4fdf2ab, retrieved 2026-11-17, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: symbol generated from the datasheet pin table; footprint an Adom_Gen land derived from the manufacturer drawing; 3D model generated to fit that land.
# BMP581
**Bosch Sensortec** · Pressure Sensors · LGA-10(2x2)
BMP581 from Bosch Sensortec, in a LGA-10(2x2). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model). The symbol is generated from that pin table, the footprint is an Adom_Gen land derived from the manufacturer drawing, and the 3D model is generated to fit it.
## Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | VDDIO | power_in | Digital interface supply VDDIO, connected to the host interface supply. |
| 2 | SCK | input | Serial clock input, used in both SPI 4-wire and SPI 3-wire modes. |
| 3 | VSS | power_in | Ground; all VSS pins must be connected to GND. |
| 4 | SDI | bidirectional | Serial data input in SPI 4-wire mode and bidirectional SDI/SDO data pad in SPI 3-wire mode; it must be tied to low or high and not left floating. |
| 5 | SDO | bidirectional | Serial data output in SPI 4-wire mode; in SPI 3-wire mode it must be left floating (DNC). |
| 6 | CSB | input | Chip select input, active low. |
| 7 | INT | output | Interrupt output to the host INT input; it may be connected to GND or left unconnected only with INT_CONFIG.int_en disabled or the recommended settings. |
| 8 | VSS | power_in | Ground; all VSS pins must be connected to GND. |
| 9 | VSS | power_in | Ground; all VSS pins must be connected to GND. |
| 10 | VDD | power_in | Analog supply VDD for the sensor. |
## Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Bosch Sensortec |
| Package | LGA-10(2x2) |
| Category | Sensors |
| Pins | 10 |
## Electrical characteristics
Limits as printed in the datasheet (page.json `metadata.characteristics` carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Relative pressure accuracy | Ap_rel | -0.4 | | 0.4 | Pa | 900, 1100 hPa, 25 °C, 1 kPa steps | 8 |
| Absolute pressure accuracy | Ap_abs | -30 | | 30 | Pa | 300, 1100 hPa, -5, 65 °C, including TCO | 8 |
| Absolute accuracy pressure (full range) | Ap_abs_full_range | -75 | | 75 | Pa | 300, 1100 hPa, -40, 85 °C, incl. solder drift, TCO after qualification | 9 |
| Offset temperature coefficient | TCO | -0.5 | | 0.5 | Pa/K | 300, 1100 hPa, -5, 65 °C, 10 K steps | 9 |
| Long term drift | ∆Pstab_long | -10 | | 10 | Pa | Drift during 1 year | 9 |
| Short term drift | ∆Pstab_short | -1.5 | | 1.5 | Pa | Drift during 24 h at constant pressure and temperature | 9 |
| Solder drift | | -30 | | 30 | Pa | 5x reflow soldering after storage in standard conditions (25 °C / 100 kPa) | 9 |
| Absolute accuracy temperature | At_abs | -0.5 | | 0.5 | K | -5 .. 55°C | 10 |
| Absolute accuracy temperature full range | At_abs_full | -0.5 | | 0.5 | K | -40 .. 85°C | 10 |
| Pressure noise low power | Vp_low_power | | 0.78 | 0.95 | PaRMS | OSR set to lowest power | 8 |
| Pressure noise high resolution | Vp_hi_res | | 0.21 | 0.25 | PaRMS | OSR set to high resolution | 8 |
| Power supply voltage | VDD | 1.71 | | 3.6 | V | | 10 |
| Power supply voltage I/Os | VDDIO | 1.08 | | 3.6 | V | | 10 |
| Supply ramp time | t_VDDramp & t_VDDIOramp | 0.01 | | 10 | ms | 10% to 90% of target voltage | 10 |
| Operational temperature range | TOP_full | -40 | | 85 | °C | | 10 |
| ODR accuracy | | -10 | | 10 | % | -40..85°C | 10 |
| Power-up time | t_powup | | | 2 | ms | Time to first communication after both VDD > VDDmin and VDDIO > VDDIOmin | 10 |
| Start-up time from STANDBY | t_startup | | | 3 | ms | Time from mode change to start of measurement | 11 |
| Start-up time from DEEP STANDBY | tstartup_deep | | | 4 | ms | Time from mode change to start of measurement | 11 |
| Re-configuration time | treconf | | | 3 | ms | Time from configuration change in NORMAL or CONTINUOUS mode to start of first measurement | 11 |
| Re-configuration time (deep) | treconf_deep | | | 4 | ms | Time from configuration change in NORMAL or CONTINUOUS mode to start of first measurement | 11 |
| Time to standby | tstandby | | | 2.5 | ms | Time from any mode to STANDBY | 11 |
| Soft reset duration | tsoft_res | | | 2 | ms | Time from trigger of soft reset until device ready | 11 |
| I3C interface clock | fi3C | 0.1 | 12.5 | 12.9 | MHz | @ VDDIO > 1.62 V - Normal Mode & Fast Mode @ Cbus < 550pF - Fast Mode + @Cbus > 100pF | 11 |
| SPI interface clock | fspi | | | 12 | MHz | @ VDDIO ≥ 1.62 V, Cbus ≤ 80 pF 4-wire/ 3-wire; modes 0 and 3 | 11 |
| SPI interface clock low voltage | fspi_lowv | | | 7 | MHz | @ VDDIO ≤ 1.62 V, Cbus ≤ 40 pF 4-wire/ 3-wire; modes 0 and 3 | 11 |
| Peak current | ipeak | | | 260 | μA | maximum DC current | 12 |
| Deep Standby current | | | | 0.55 | μA | 25 °C and VDDIO=VDD=1.8 V | 12 |
| Deep Standby current | | | | 1.5 | μA | 55 °C and VDDIO=VDD=1.8 V | 12 |
| Standby current | | | | 1 | μA | 25 °C and VDDIO=VDD=1.8 V | 12 |
| Standby current | | | | 3.5 | μA | 55 °C and VDDIO=VDD=1.8 V | 12 |
| Current consumption low power mode | | | | 1.3 | μA | OSR set to lowest power, Low Power Mode ODR=1 Hz 25 °C | 12 |
| INT pulse length | tint_pulse | 90 | 105 | 121 | μs | Pulse length in pulsed mode | 12 |
| INT minimum deassert time | tint_deassert | 90 | 105 | 121 | μs | Minimum time between INT pin assert | 12 |
| Maximum output rate (ODR) | | | | 489 | Hz | in CONTINUOUS mode, pressure and temperature measured | 12 |
| Output data rate (ODR) range | | 0.125 | | 240 | Hz | in NORMAL mode | 12 |
| Pull-up resistance at CSB pin | RPU_CSB | 74 | 100 | 131 | kOhm | I2C mode, relevant for interface mode selection | 13 |
| Storage temperature | | -40 | | 125 | °C | ≤ 65 % r.h. Standard conditions: + 25°C and 40% r.h. | 13 |
| Supply voltage | VDD | -0.3 | | 4.3 | V | | 13 |
| Max voltage at I/O pins | VSSIO | -0.3 | | | V | Max voltage at I/O pins, VSSIO-0.3 V to VDDIO + 0.3 V | 13 |
## CAD (Adom-generated)
- Symbol: `BMP581`
- Footprint: `Adom_Gen:BOSCH_SENSORTECH_BMP581_1a03d8`
- 3D model: generated to fit the land (STEP)
- 3D model files: `bmp581-etched.step` / `bmp581-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `bmp581.step` / `bmp581.glb` are the bare package body.
## Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- **Datasheet:** [Bosch Sensortec datasheet](https://www.bosch-sensortec.com/media/boschsensortec/downloads/datasheets/bst-bmp581-ds004.pdf) (75 pp, sha256 `ddcf4202c4fdf2ab`, retrieved 2026-11-17, tier: manufacturer)
- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.3`, primary `claude-haiku-5-5` (text), consensus `claude-sonnet-5-5` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
- **CAD:** symbol generated from the datasheet pin table; footprint an Adom_Gen land derived from the manufacturer drawing; 3D model generated to fit that land.
[Datasheet PDF](docs/bmp581-datasheet.pdf)