BD6964F-GE2 from ROHM Semicon, in a SOP-8. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin	Name	Type	Function
1	OUT2	output	Motor output driving the motor coil in the BTL bridge, with VOMAX rated at 15 V and output current IOMAX rated at 1000 mA, which must not exceed Pd.
2	VCC	power_in	Power supply input with an operating supply voltage range of 3.3 to 14 V and an absolute maximum rating of 15 V.
3	H+	input	Non-inverting Hall sensor input; the Hall input voltage range is 0 to VCC/3 V.
4	H-	input	Inverting Hall sensor input; the Hall input voltage range is 0 to VCC/3 V.
5	AL	output	Lock alarm signal output implemented as an open-drain output that requires a pull-up resistor, with a maximum voltage of 15 V and a maximum current of 10 mA.
6	PWM	input	PWM speed control input, with an H level of 2.0 V to VCC+0.3 V, an L level of -0.3 to 0.8 V, and an input frequency of 0.02 to 50 kHz (50 kHz maximum).
7	OUT1	output	Motor output driving the motor coil in the BTL bridge, with VOMAX rated at 15 V and output current IOMAX rated at 1000 mA, which must not exceed Pd.
8	GND	power_in	Ground reference pin for the IC.

Key specifications

Parameter	Value
Manufacturer	ROHM Semicon
Package	SOP-8
Category	Power Management ICs
Pins	8

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter	Symbol	Min	Typ	Max	Unit	Conditions	Page
Supply Voltage	VCC			15	V		1
Output Voltage	VOMAX			15	V		1
AL Signal Output Voltage	VAL			15	V		1
AL Signal Output Current	IAL			10	mA		1
Output Current	IOMAX			1000	mA	Note 2: not to exceed Pd	1
Power Dissipation	Pd			0.78	W	Note 1: reduce by 6.24mW/°C over 25°C; 70.0mm×70.0mm×1.6mm glass epoxy board	1
Operating Temperature	Topr	-40		105	°C		1
Storage Temperature	Tstg	-55		150	°C		1
Junction Temperature	Tjmax			150	°C		1
Operating supply voltage range	VCC	3.3		14	V		2
Hall input voltage range	VH	0			V	Upper limit printed as VCC/3	2
Circuit Current 1	ICC1	1	3	5	mA	PWM=GND Figure 1	2
Circuit Current 2	ICC2	2	5	8	mA	PWM=OPEN Figure 2	2
Input Offset Voltage	VHOFS	-6		6	mV		2
PWM Input H Level	VPWMH	2			V	Max printed as Vcc+0.3	2
PWM Input L Level	VPWML	-0.3		0.8	V		2
PWM Input Current (high)	IPWMH	11	22	33	µA	PWM=5V Figure 3	2
PWM Input Current (low)	IPWML	-42	-28	-14	µA	PWM=GND Figure 3	2
Input Frequency	FPWM	0.02		50	kHz		2
Output Voltage	VO		0.4	0.6	V	IO=300mA; upper and lower total; Figure 4 to 7	2
Input-output Gain	GIO	45	48	51	dB		2
AL Low Voltage	VALL			0.4	V	IAL=5mA Figure 8,9	2
AL Leak Current	IALL			20	µA	VAL=15V Figure 10	2
Lock Detection ON time	tON	0.35	0.5	0.65	s	Figure 11	2
Lock Detection OFF time	tOFF	3.5	5	6.5	s	Figure 12	2
Power derating above 25°C			6.24		mW/°C	Over 25°C; 70.0mm×70.0mm×1.6mm glass epoxy board	1

CAD (KiCad official)

Symbol: BD6964F-GE2
Footprint: Package_SO:SOIC-8_3.9x4.9mm_P1.27mm
3D model: SOP-8 (KiCad packages3D, STEP)
3D model files: bd6964f-ge2-etched.step / bd6964f-ge2-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); bd6964f-ge2.step / bd6964f-ge2.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

Datasheet: ROHM Semicon datasheet (17 pp, sha256 3ae0483832a9a009, retrieved 2026-10-31, tier: manufacturer)
Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-haiku-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF

BD6964F-GE2

Verified BD6964F-GE2

Verification log 1 record

3D Model

Symbol & Footprint

Schematic Symbol

PCB Footprint

Datasheet

README