BD62220AEFV-E2

ROHM Semicon · Brushed DC Motor Drivers · HTSSOP-28-EP

BD62220AEFV-E2 from ROHM Semicon, in a HTSSOP-28-EP. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin	Name	Type	Function
1	GND	power_in	Ground terminal; the wiring impedance from this terminal should be made as low as possible to reach the lowest electrical potential in any operating state.
2	OUT1B	output	H bridge output terminal for channel 1, which carries motor drive current and has a built-in clamp against electrostatic destruction that must not be exceeded by surge voltage.
3	RNF1	passive	Connection terminal of the output-current detection resistor, which should be 0.1 Ω to 0.3 Ω and must not be left open or shorted to GND.
4	RNF1S	input	Input terminal of the channel 1 current limit comparator, which must be connected to RNF1 when PWM constant current control is used.
5	OUT1A	output	H bridge output terminal for channel 1, which carries motor drive current and has a built-in clamp against electrostatic destruction that must not be exceeded by surge voltage.
6	NC	unconnected	No connection; the terminal is electrically unconnected to the internal circuit.
7	VCC1	power_in	Power supply terminal that must be shorted externally to VCC2 and bypassed with 100 µF to 470 µF close to the pin, with the supply kept within the 8 V to 28 V recommended range and never exceeding the 36 V absolute maximum.
8	NC	unconnected	No connection; the terminal is electrically unconnected to the internal circuit.
9	GND	power_in	Ground terminal; the wiring impedance from this terminal should be made as low as possible to reach the lowest electrical potential in any operating state.
10	CR	passive	Connection terminal for the switching-frequency timing network, which requires an external C of 330 pF to 680 pF and R of 10 kΩ to 150 kΩ to GND and must not be left open when PWM constant current control is used.
11	VREF1	input	Current limit value setting terminal for channel 1, where VREF must stay within 0 V to 2.0 V and must not be left open.
12	VREF2	input	Current limit value setting terminal for channel 2, where VREF must stay within 0 V to 2.0 V and must not be left open.
13	PS	input	Power save terminal where L puts the circuit into standby with motor outputs open and H enables active operation, with a delay of up to 40 µs when returning from standby.
14	TEST1	input	Test terminal that must be connected to GND, since it may malfunction if left unconnected.
15	FAILA	output	Open-drain fault output that goes low on over-current protection or thermal shutdown, and requires a 5 kΩ to 100 kΩ pull-up to a supply below 7 V (such as 5 V or 3.3 V).
16	IN1A	input	H bridge control input for channel 1 that sets forward, reverse, brake, or open output logic together with IN1B and PS.
17	IN1B	input	H bridge control input for channel 1 that sets forward, reverse, brake, or open output logic together with IN1A and PS.
18	TEST2	input	Test terminal that must be connected to GND, since it may malfunction if left unconnected.
19	IN2A	input	H bridge control input for channel 2 that sets forward, reverse, brake, or open output logic together with IN2B and PS.
20	IN2B	input	H bridge control input for channel 2 that sets forward, reverse, brake, or open output logic together with IN2A and PS.
21	NC	unconnected	No connection; the terminal is electrically unconnected to the internal circuit.
22	VCC2	power_in	Power supply terminal that must be shorted externally to VCC1 and bypassed with 100 µF to 470 µF close to the pin, with the supply kept within the 8 V to 28 V recommended range and never exceeding the 36 V absolute maximum.
23	NC	unconnected	No connection; the terminal is electrically unconnected to the internal circuit.
24	OUT2A	output	H bridge output terminal for channel 2, which carries motor drive current and has a built-in clamp against electrostatic destruction that must not be exceeded by surge voltage.
25	RNF2S	input	Input terminal of the channel 2 current limit comparator, which must be connected to RNF2 when PWM constant current control is used.
26	RNF2	passive	Connection terminal of the output-current detection resistor, which should be 0.1 Ω to 0.3 Ω and must not be left open or shorted to GND.
27	OUT2B	output	H bridge output terminal for channel 2, which carries motor drive current and has a built-in clamp against electrostatic destruction that must not be exceeded by surge voltage.
28	NC	unconnected	No connection; the terminal is electrically unconnected to the internal circuit.
29	EP	passive	Exposed pad (from the footprint; not named in the datasheet pin table).

Key specifications

Parameter	Value
Manufacturer	ROHM Semicon
Package	HTSSOP-28-EP
Category	Motor Driver ICs
Pins	29

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter	Symbol	Min	Typ	Max	Unit	Conditions	Page
Circuit Current at Standby	ICCST			10	µA	PS=L	4
Circuit Current	ICC		2.5	5	mA	PS=H, VREFx=2V	4
H Level Input Voltage	VIN2H	2			V		4
L Level Input Voltage	VIN2L			0.8	V		4
H Level Input Current	IIN2H	35	50	100	µA	VIN2=5V	4
L Level Input Current	IIN2L	-10	0		µA	VIN2=0V	4
Output ON-Resistance (sum of upper and lower)	RON		0.65	0.85	Ω	IOUT =±1.0A (Sum of upper and lower)	4
Output Leak Current	ILEAK			10	µA		4
RNFX Input Current	IRNF	-80	-40		µA	RNFx=0V	4
VREFx Input Current	IVREF	-2	-0.1		µA	VREFx=0V	4
VREFx Input Voltage Range	VVREF	0		2	V		4
Minimum on Time (Blank Time)	tONMIN	0.7	1.5	3	µs		4
Current Limit Comparator Threshold	VCTH	0.23	0.25	0.27	V	VREFx=2V	4
Supply Voltage	VCC1,2	8		28	V	Ta= -25 to +85°C	3
Maximum Output Current (Continuous)	IOUT			1.4	A/ch	Ta= -25 to +85°C; Note 5: do not exceed Pd, ASO and Tjmax=150°C	3
Supply Voltage	VCC1,2	-0.2		36	V	Ta=25°C	3
Power Dissipation (Note 1: 70mm×70mm×1.6mm glass epoxy board)	Pd			1.45	W	Note 1: derate 11.6mW/°C above Ta=25°C	3
Power Dissipation (Note 2: 4-layer recommended board)	Pd			4.7	W	Note 2: derate 37.6mW/°C above Ta=25°C	3
Input Voltage for Control Pin	VIN	-0.2		5.5	V	Ta=25°C	3
RNF Maximum Voltage	VRNF			0.7	V	Ta=25°C	3
Output Current	IOUT			2	A/ch	Ta=25°C; Note 3: do not exceed Pd, ASO and Tjmax=150°C	3
Output Current (peak)	IOUTPEAK			2.8	A/ch	Ta=25°C; Note 4: pulse width tw ≤1ms, duty 20ms	3
Operating Temperature Range	Topr	-25		85	°C		3
Storage Temperature Range	Tstg	-55		150	°C		3
Thermal resistance junction-to-ambient, Board ① (1-layer, no copper on back)	θja		86.2		°C/W	Board①: 1-layer board (Copper foil on the back 0mm), solder-connected back metal	18
Thermal resistance junction-to-ambient, Board ② (2-layer, 15mm×15mm copper on back)	θja		67.6		°C/W	Board②: 2-layer board (Copper foil on the back 15mm*15mm), solder-connected back metal	18
Thermal resistance junction-to-ambient, Board ③ (2-layer, 70mm×70mm copper on back)	θja		37.9		°C/W	Board③: 2-layer board (Copper foil on the back 70mm*70mm), solder-connected back metal	18
Thermal resistance junction-to-ambient, Board ④ (4-layer, 70mm×70mm copper on back)	θja		26.6		°C/W	Board④: 4-layer board (Copper foil on the back 70mm*70mm), solder-connected back metal	18

CAD (KiCad official)

Symbol: BD62220AEFV-E2
Footprint: Package_SO:TSSOP-28-1EP_4.4x9.7mm_P0.65mm_EP2.85x6.7mm
3D model: HTSSOP-28-EP (KiCad packages3D, STEP)
3D model files: bd62220aefv-e2-etched.step / bd62220aefv-e2-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); bd62220aefv-e2.step / bd62220aefv-e2.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

Datasheet: ROHM Semicon datasheet (24 pp, sha256 beadf2a0cfc56377, retrieved 2026-10-17, tier: lcsc)
Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-haiku-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF

# BD62220AEFV-E2

**ROHM Semicon** · Brushed DC Motor Drivers · HTSSOP-28-EP

BD62220AEFV-E2 from ROHM Semicon, in a HTSSOP-28-EP. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.

## Pinout

| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | GND | power_in | Ground terminal; the wiring impedance from this terminal should be made as low as possible to reach the lowest electrical potential in any operating state. |
| 2 | OUT1B | output | H bridge output terminal for channel 1, which carries motor drive current and has a built-in clamp against electrostatic destruction that must not be exceeded by surge voltage. |
| 3 | RNF1 | passive | Connection terminal of the output-current detection resistor, which should be 0.1 Ω to 0.3 Ω and must not be left open or shorted to GND. |
| 4 | RNF1S | input | Input terminal of the channel 1 current limit comparator, which must be connected to RNF1 when PWM constant current control is used. |
| 5 | OUT1A | output | H bridge output terminal for channel 1, which carries motor drive current and has a built-in clamp against electrostatic destruction that must not be exceeded by surge voltage. |
| 6 | NC | unconnected | No connection; the terminal is electrically unconnected to the internal circuit. |
| 7 | VCC1 | power_in | Power supply terminal that must be shorted externally to VCC2 and bypassed with 100 µF to 470 µF close to the pin, with the supply kept within the 8 V to 28 V recommended range and never exceeding the 36 V absolute maximum. |
| 8 | NC | unconnected | No connection; the terminal is electrically unconnected to the internal circuit. |
| 9 | GND | power_in | Ground terminal; the wiring impedance from this terminal should be made as low as possible to reach the lowest electrical potential in any operating state. |
| 10 | CR | passive | Connection terminal for the switching-frequency timing network, which requires an external C of 330 pF to 680 pF and R of 10 kΩ to 150 kΩ to GND and must not be left open when PWM constant current control is used. |
| 11 | VREF1 | input | Current limit value setting terminal for channel 1, where VREF must stay within 0 V to 2.0 V and must not be left open. |
| 12 | VREF2 | input | Current limit value setting terminal for channel 2, where VREF must stay within 0 V to 2.0 V and must not be left open. |
| 13 | PS | input | Power save terminal where L puts the circuit into standby with motor outputs open and H enables active operation, with a delay of up to 40 µs when returning from standby. |
| 14 | TEST1 | input | Test terminal that must be connected to GND, since it may malfunction if left unconnected. |
| 15 | FAILA | output | Open-drain fault output that goes low on over-current protection or thermal shutdown, and requires a 5 kΩ to 100 kΩ pull-up to a supply below 7 V (such as 5 V or 3.3 V). |
| 16 | IN1A | input | H bridge control input for channel 1 that sets forward, reverse, brake, or open output logic together with IN1B and PS. |
| 17 | IN1B | input | H bridge control input for channel 1 that sets forward, reverse, brake, or open output logic together with IN1A and PS. |
| 18 | TEST2 | input | Test terminal that must be connected to GND, since it may malfunction if left unconnected. |
| 19 | IN2A | input | H bridge control input for channel 2 that sets forward, reverse, brake, or open output logic together with IN2B and PS. |
| 20 | IN2B | input | H bridge control input for channel 2 that sets forward, reverse, brake, or open output logic together with IN2A and PS. |
| 21 | NC | unconnected | No connection; the terminal is electrically unconnected to the internal circuit. |
| 22 | VCC2 | power_in | Power supply terminal that must be shorted externally to VCC1 and bypassed with 100 µF to 470 µF close to the pin, with the supply kept within the 8 V to 28 V recommended range and never exceeding the 36 V absolute maximum. |
| 23 | NC | unconnected | No connection; the terminal is electrically unconnected to the internal circuit. |
| 24 | OUT2A | output | H bridge output terminal for channel 2, which carries motor drive current and has a built-in clamp against electrostatic destruction that must not be exceeded by surge voltage. |
| 25 | RNF2S | input | Input terminal of the channel 2 current limit comparator, which must be connected to RNF2 when PWM constant current control is used. |
| 26 | RNF2 | passive | Connection terminal of the output-current detection resistor, which should be 0.1 Ω to 0.3 Ω and must not be left open or shorted to GND. |
| 27 | OUT2B | output | H bridge output terminal for channel 2, which carries motor drive current and has a built-in clamp against electrostatic destruction that must not be exceeded by surge voltage. |
| 28 | NC | unconnected | No connection; the terminal is electrically unconnected to the internal circuit. |
| 29 | EP | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |

## Key specifications

| Parameter | Value |
|---|---|
| Manufacturer | ROHM Semicon |
| Package | HTSSOP-28-EP |
| Category | Motor Driver ICs |
| Pins | 29 |

## Electrical characteristics

Limits as printed in the datasheet (page.json `metadata.characteristics` carries them as data).

| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Circuit Current at Standby | ICCST |  |  | 10 | µA | PS=L | 4 |
| Circuit Current | ICC |  | 2.5 | 5 | mA | PS=H, VREFx=2V | 4 |
| H Level Input Voltage | VIN2H | 2 |  |  | V |  | 4 |
| L Level Input Voltage | VIN2L |  |  | 0.8 | V |  | 4 |
| H Level Input Current | IIN2H | 35 | 50 | 100 | µA | VIN2=5V | 4 |
| L Level Input Current | IIN2L | -10 | 0 |  | µA | VIN2=0V | 4 |
| Output ON-Resistance (sum of upper and lower) | RON |  | 0.65 | 0.85 | Ω | IOUT =±1.0A (Sum of upper and lower) | 4 |
| Output Leak Current | ILEAK |  |  | 10 | µA |  | 4 |
| RNFX Input Current | IRNF | -80 | -40 |  | µA | RNFx=0V | 4 |
| VREFx Input Current | IVREF | -2 | -0.1 |  | µA | VREFx=0V | 4 |
| VREFx Input Voltage Range | VVREF | 0 |  | 2 | V |  | 4 |
| Minimum on Time (Blank Time) | tONMIN | 0.7 | 1.5 | 3 | µs |  | 4 |
| Current Limit Comparator Threshold | VCTH | 0.23 | 0.25 | 0.27 | V | VREFx=2V | 4 |
| Supply Voltage | VCC1,2 | 8 |  | 28 | V | Ta= -25 to +85°C | 3 |
| Maximum Output Current (Continuous) | IOUT |  |  | 1.4 | A/ch | Ta= -25 to +85°C; Note 5: do not exceed Pd, ASO and Tjmax=150°C | 3 |
| Supply Voltage | VCC1,2 | -0.2 |  | 36 | V | Ta=25°C | 3 |
| Power Dissipation (Note 1: 70mm×70mm×1.6mm glass epoxy board) | Pd |  |  | 1.45 | W | Note 1: derate 11.6mW/°C above Ta=25°C | 3 |
| Power Dissipation (Note 2: 4-layer recommended board) | Pd |  |  | 4.7 | W | Note 2: derate 37.6mW/°C above Ta=25°C | 3 |
| Input Voltage for Control Pin | VIN | -0.2 |  | 5.5 | V | Ta=25°C | 3 |
| RNF Maximum Voltage | VRNF |  |  | 0.7 | V | Ta=25°C | 3 |
| Output Current | IOUT |  |  | 2 | A/ch | Ta=25°C; Note 3: do not exceed Pd, ASO and Tjmax=150°C | 3 |
| Output Current (peak) | IOUTPEAK |  |  | 2.8 | A/ch | Ta=25°C; Note 4: pulse width tw ≤1ms, duty 20ms | 3 |
| Operating Temperature Range | Topr | -25 |  | 85 | °C |  | 3 |
| Storage Temperature Range | Tstg | -55 |  | 150 | °C |  | 3 |
| Thermal resistance junction-to-ambient, Board ① (1-layer, no copper on back) | θja |  | 86.2 |  | °C/W | Board①: 1-layer board (Copper foil on the back 0mm), solder-connected back metal | 18 |
| Thermal resistance junction-to-ambient, Board ② (2-layer, 15mm×15mm copper on back) | θja |  | 67.6 |  | °C/W | Board②: 2-layer board (Copper foil on the back 15mm*15mm), solder-connected back metal | 18 |
| Thermal resistance junction-to-ambient, Board ③ (2-layer, 70mm×70mm copper on back) | θja |  | 37.9 |  | °C/W | Board③: 2-layer board (Copper foil on the back 70mm*70mm), solder-connected back metal | 18 |
| Thermal resistance junction-to-ambient, Board ④ (4-layer, 70mm×70mm copper on back) | θja |  | 26.6 |  | °C/W | Board④: 4-layer board (Copper foil on the back 70mm*70mm), solder-connected back metal | 18 |

## CAD (KiCad official)

- Symbol: `BD62220AEFV-E2`
- Footprint: `Package_SO:TSSOP-28-1EP_4.4x9.7mm_P0.65mm_EP2.85x6.7mm`
- 3D model: HTSSOP-28-EP (KiCad packages3D, STEP)
- 3D model files: `bd62220aefv-e2-etched.step` / `bd62220aefv-e2-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `bd62220aefv-e2.step` / `bd62220aefv-e2.glb` are the bare package body.

## Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

- **Datasheet:** [ROHM Semicon datasheet](https://jlcpcb.com/api/file/downloadByFileSystemAccessId/8589902158066974720) (24 pp, sha256 `beadf2a0cfc56377`, retrieved 2026-10-17, tier: lcsc)
- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.3`, primary `claude-haiku-5-5` (text), consensus `claude-sonnet-5-5` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
- **CAD:** KiCad official libraries (CC-BY-SA 4.0).

[Datasheet PDF](docs/bd62220aefv-e2-datasheet.pdf)