component
AT24CS04-SSHM-T
Public Made by Adomby adom
Microchip Tech EEPROM, SOIC-8. Pinout cross-checked by two models against the datasheet, KiCad symbol/footprint/3D.
3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Contents
README
markdownAT24CS04-SSHM-T
Microchip Tech · EEPROM · SOIC-8
AT24CS04-SSHM-T from Microchip Tech, in a SOIC-8. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | NC | unconnected | No connect pin with no internal function stated on the 8-lead SOIC. |
| 2 | A1 | input | Device address input on the AT24CS04, hard-wired to GND or VCC to allow up to four devices on a bus, and internally pulled down to GND if left unconnected. |
| 3 | A2 | input | Device address input, hard-wired to GND or VCC, and internally pulled down to GND if left floating (a known state is recommended). |
| 4 | GND | power_in | Ground reference for the power supply, to be connected to system ground. |
| 5 | SDA | bidirectional | Open-drain bidirectional serial data pin that needs an external pull-up resistor (not to exceed 10 kΩ) and may be wire-ORed with other open-drain devices on the bus. |
| 6 | SCL | input | Serial clock input that latches command and input data on the rising edge and clocks output data out on the falling edge, and must be forced high or pulled high when the bus is idle. |
| 7 | WP | input | Write-protect input: GND allows normal writes, VCC inhibits all writes to the full protected array, and it is internally pulled down to GND if left floating. |
| 8 | VCC | power_in | Device power supply pin, operating from 1.7V to 5.5V. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Microchip Tech |
| Package | SOIC-8 |
| Category | Memory |
| Pins | 8 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Supply Voltage | VCC | 1.7 | 5.5 | V | 9 | ||
| Supply Current Read | ICC1 | 0.4 | 1 | mA | VCC = 5.0V, Read at 400 kHz | 9 | |
| Supply Current Write | ICC2 | 2 | 3 | mA | VCC = 5.0V, Write at 400 kHz | 9 | |
| Standby Current | ISB | 1 | μA | VCC = 1.7V, VIN = VCC or GND | 9 | ||
| Standby Current | ISB | 6 | μA | VCC = 5.5V, VIN = VCC or GND | 9 | ||
| Input Leakage Current | ILI | 0.1 | 3 | μA | VIN = VCC or GND | 9 | |
| Output Leakage Current | ILO | 0.05 | 3 | μA | VOUT = VCC or GND | 9 | |
| Input Low Level | VIL | -0.6 | V | Note 2 | 9 | ||
| Output Low Level | VOL1 | 0.2 | V | VCC = 1.7V, IOL = 0.15 mA | 10 | ||
| Output Low Level | VOL2 | 0.4 | V | VCC = 3.0V, IOL = 2.1 mA | 10 | ||
| Clock Frequency, SCL (Fast Mode) | fSCL | 400 | kHz | VCC = 1.7V to 2.5V | 10 | ||
| Clock Frequency, SCL (Fast Mode Plus) | fSCL | 1000 | kHz | VCC = 2.5V to 5.5V | 10 | ||
| Clock Pulse Width Low (Fast Mode) | tLOW | 1200 | ns | VCC = 1.7V to 2.5V | 10 | ||
| Clock Pulse Width Low (Fast Mode Plus) | tLOW | 500 | ns | VCC = 2.5V to 5.5V | 10 | ||
| Clock Pulse Width High (Fast Mode) | tHIGH | 600 | ns | VCC = 1.7V to 2.5V | 10 | ||
| Clock Pulse Width High (Fast Mode Plus) | tHIGH | 400 | ns | VCC = 2.5V to 5.5V | 10 | ||
| Input Filter Spike Suppression (Fast Mode) | tI | 100 | ns | VCC = 1.7V to 2.5V | 10 | ||
| Input Filter Spike Suppression (Fast Mode Plus) | tI | 50 | ns | VCC = 2.5V to 5.5V | 10 | ||
| Clock Low to Data Out Valid (Fast Mode) | tAA | 100 | 900 | ns | VCC = 1.7V to 2.5V | 10 | |
| Clock Low to Data Out Valid (Fast Mode Plus) | tAA | 50 | 450 | ns | VCC = 2.5V to 5.5V | 10 | |
| Bus Free Time between Stop and Start (Fast Mode) | tBUF | 1300 | ns | VCC = 1.7V to 2.5V | 10 | ||
| Bus Free Time between Stop and Start (Fast Mode Plus) | tBUF | 500 | ns | VCC = 2.5V to 5.5V | 10 | ||
| Start Hold Time (Fast Mode) | tHD.STA | 600 | ns | VCC = 1.7V to 2.5V | 10 | ||
| Start Hold Time (Fast Mode Plus) | tHD.STA | 250 | ns | VCC = 2.5V to 5.5V | 10 | ||
| Start Set-up Time (Fast Mode) | tSU.STA | 600 | ns | VCC = 1.7V to 2.5V | 10 | ||
| Start Set-up Time (Fast Mode Plus) | tSU.STA | 250 | ns | VCC = 2.5V to 5.5V | 10 | ||
| Data In Hold Time (Fast Mode) | tHD.DAT | 0 | ns | VCC = 1.7V to 2.5V | 10 | ||
| Data In Hold Time (Fast Mode Plus) | tHD.DAT | 0 | ns | VCC = 2.5V to 5.5V | 10 | ||
| Data In Set-up Time (Fast Mode) | tSU.DAT | 100 | ns | VCC = 1.7V to 2.5V | 10 | ||
| Data In Set-up Time (Fast Mode Plus) | tSU.DAT | 100 | ns | VCC = 2.5V to 5.5V | 10 | ||
| Inputs Rise Time (Fast Mode) | tR | 300 | ns | VCC = 1.7V to 2.5V | 10 | ||
| Inputs Rise Time (Fast Mode Plus) | tR | 300 | ns | VCC = 2.5V to 5.5V | 10 | ||
| Inputs Fall Time (Fast Mode) | tF | 300 | ns | VCC = 1.7V to 2.5V | 10 | ||
| Inputs Fall Time (Fast Mode Plus) | tF | 100 | ns | VCC = 2.5V to 5.5V | 10 | ||
| Stop Set-up Time (Fast Mode) | tSU.STO | 600 | ns | VCC = 1.7V to 2.5V | 10 | ||
| Stop Set-up Time (Fast Mode Plus) | tSU.STO | 250 | ns | VCC = 2.5V to 5.5V | 10 | ||
| Data Out Hold Time (Fast Mode) | tDH | 50 | ns | VCC = 1.7V to 2.5V | 10 | ||
| Data Out Hold Time (Fast Mode Plus) | tDH | 50 | ns | VCC = 2.5V to 5.5V | 10 | ||
| Write Cycle Time (Fast Mode) | tWR | 5 | ms | VCC = 1.7V to 2.5V | 10 | ||
| Write Cycle Time (Fast Mode Plus) | tWR | 5 | ms | VCC = 2.5V to 5.5V | 10 | ||
| Time required after VCC is stable before the device can accept commands | tPUP | 100 | µs | 11 | |||
| Power-on Reset Threshold Voltage | VPOR | 1.5 | V | 11 | |||
| Minimum time at VCC = 0V between power cycles | tPOFF | 500 | ms | 11 | |||
| Input/Output Capacitance (SDA) | CI/O | 8 | pF | VI/O = 0V | 12 | ||
| Input Capacitance (A1, A2 and SCL) | CIN | 6 | pF | VIN = 0V | 12 | ||
| Write Endurance | 1e+06 | Write Cycles | TA = 25°C, VCC = 3.3V, Page Write mode | 12 | |||
| Data Retention | 100 | Years | TA = 55°C | 12 | |||
| Temperature under bias | -55 | 125 | °C | 9 | |||
| Storage temperature | -65 | 150 | °C | 9 | |||
| VCC | VCC | 6.25 | V | 9 | |||
| Voltage on any pin with respect to ground | -1 | 7 | V | 9 | |||
| DC output current | 5 | mA | 9 | ||||
| ESD protection | 4 | kV | >4 kV | 9 | |||
| Operating Temperature (Case), Industrial | -40 | 85 | °C | Industrial Temperature Range | 9 |
Materials and finish
As the datasheet states them (page.json metadata.appearance; the 3D model's colours follow it).
| Part | Material | Colour / plating | Datasheet says | Page |
|---|---|---|---|---|
| contacts | tin | 8-Lead Plastic Small Outline (SN) - Narrow, 3.90 mm (.150 In.) Body [SOIC] A A2 | 27 |
CAD (KiCad official)
- Symbol:
AT24CS04-SSHM-T - Footprint:
Package_SO:SOIC-8_3.9x4.9mm_P1.27mm - 3D model: SOIC-8 (KiCad packages3D, STEP)
- 3D model files:
at24cs04-sshm-t-etched.step/at24cs04-sshm-t-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);at24cs04-sshm-t.step/at24cs04-sshm-t.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Microchip Tech datasheet (43 pp, sha256
fe44cb2756a478b7, retrieved 2026-10-23, tier: lcsc) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-sonnet-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).