AT24C32D-SSHM-T

{
 "schema": "adom.pads/1",
 "slug": "at24c32d-sshm-t",
 "footprint": "SOIC-8_3.9x4.9mm_P1.27mm",
 "generated_from": {
  "footprint": "SOIC-8_3.9x4.9mm_P1.27mm@sha256:074ecb2092b24fa4",
  "pins": "page.json:component.pins",
  "overrides": null
 },
 "pin1": {
  "pad": "1",
  "at": [
   -2.475,
   -1.905
  ],
  "corner": "top-left",
  "source": "silk-marker",
  "derived_from": "SOIC-8_3.9x4.9mm_P1.27mm@sha256:074ecb2092b24fa4"
 },
 "pad_count": 8,
 "symbol_pins": [
  "1",
  "2",
  "3",
  "4",
  "5",
  "6",
  "7",
  "8"
 ],
 "paste_apertures": 0,
 "issues": [],
 "pads": [
  {
   "pad": "1",
   "kind": "smd",
   "shape": "roundrect",
   "at": [
    -2.475,
    -1.905
   ],
   "rot": 0.0,
   "size": [
    1.95,
    0.6
   ],
   "layers": [
    "F.Cu",
    "F.Mask",
    "F.Paste"
   ],
   "thermal": false,
   "pin": "1",
   "name": "A0",
   "type": "input",
   "description": "Device address input bit 0. Hardwired high or low to set the lower bit of the 3-bit hardware slave address, allowing up to eight AT24C32D devices on the same 2-wire bus. Internally pulled to GND if left floating and VCC-plane coupling is <3 pF; Atmel recommends tying to GND when coupling is >3 pF.",
   "is_pin1": true,
   "source": {
    "geometry": "SOIC-8_3.9x4.9mm_P1.27mm.kicad_mod",
    "meaning": "page.json:component.pins",
    "correspondence": "kicad: symbol pin number == pad name"
   }
  },
  {
   "pad": "2",
   "kind": "smd",
   "shape": "roundrect",
   "at": [
    -2.475,
    -0.635
   ],
   "rot": 0.0,
   "size": [
    1.95,
    0.6
   ],
   "layers": [
    "F.Cu",
    "F.Mask",
    "F.Paste"
   ],
   "thermal": false,
   "pin": "2",
   "name": "A1",
   "type": "input",
   "description": "Device address input bit 1. Hardwired to set the middle bit of the slave address. Same floating-behavior notes as A0 (internal pull-down to GND when board-VCC coupling is <3 pF).",
   "is_pin1": false,
   "source": {
    "geometry": "SOIC-8_3.9x4.9mm_P1.27mm.kicad_mod",
    "meaning": "page.json:component.pins",
    "correspondence": "kicad: symbol pin number == pad name"
   }
  },
  {
   "pad": "3",
   "kind": "smd",
   "shape": "roundrect",
   "at": [
    -2.475,
    0.635
   ],
   "rot": 0.0,
   "size": [
    1.95,
    0.6
   ],
   "layers": [
    "F.Cu",
    "F.Mask",
    "F.Paste"
   ],
   "thermal": false,
   "pin": "3",
   "name": "A2",
   "type": "input",
   "description": "Device address input bit 2. Hardwired to set the upper bit of the slave address. Same floating-behavior notes as A0/A1.",
   "is_pin1": false,
   "source": {
    "geometry": "SOIC-8_3.9x4.9mm_P1.27mm.kicad_mod",
    "meaning": "page.json:component.pins",
    "correspondence": "kicad: symbol pin number == pad name"
   }
  },
  {
   "pad": "4",
   "kind": "smd",
   "shape": "roundrect",
   "at": [
    -2.475,
    1.905
   ],
   "rot": 0.0,
   "size": [
    1.95,
    0.6
   ],
   "layers": [
    "F.Cu",
    "F.Mask",
    "F.Paste"
   ],
   "thermal": false,
   "pin": "4",
   "name": "GND",
   "type": "power_in",
   "description": "Ground reference (0 V) for supply and all logic signals.",
   "is_pin1": false,
   "source": {
    "geometry": "SOIC-8_3.9x4.9mm_P1.27mm.kicad_mod",
    "meaning": "page.json:component.pins",
    "correspondence": "kicad: symbol pin number == pad name"
   }
  },
  {
   "pad": "5",
   "kind": "smd",
   "shape": "roundrect",
   "at": [
    2.475,
    1.905
   ],
   "rot": 0.0,
   "size": [
    1.95,
    0.6
   ],
   "layers": [
    "F.Cu",
    "F.Mask",
    "F.Paste"
   ],
   "thermal": false,
   "pin": "5",
   "name": "SDA",
   "type": "bidirectional",
   "description": "Serial data line for the 2-wire (I2C-compatible) interface. Open-drain output; requires an external pull-up resistor to VCC and may be wire-ORed with other open-drain devices. Input capacitance up to 8 pF.",
   "is_pin1": false,
   "source": {
    "geometry": "SOIC-8_3.9x4.9mm_P1.27mm.kicad_mod",
    "meaning": "page.json:component.pins",
    "correspondence": "kicad: symbol pin number == pad name"
   }
  },
  {
   "pad": "6",
   "kind": "smd",
   "shape": "roundrect",
   "at": [
    2.475,
    0.635
   ],
   "rot": 0.0,
   "size": [
    1.95,
    0.6
   ],
   "layers": [
    "F.Cu",
    "F.Mask",
    "F.Paste"
   ],
   "thermal": false,
   "pin": "6",
   "name": "SCL",
   "type": "input",
   "description": "Serial clock input for the 2-wire interface. Positive edges clock data into the device and negative edges clock data out. Supports up to 400 kHz at 1.7V VCC and up to 1 MHz at 5.0V VCC; Schmitt-trigger and noise-filtered input.",
   "is_pin1": false,
   "source": {
    "geometry": "SOIC-8_3.9x4.9mm_P1.27mm.kicad_mod",
    "meaning": "page.json:component.pins",
    "correspondence": "kicad: symbol pin number == pad name"
   }
  },
  {
   "pad": "7",
   "kind": "smd",
   "shape": "roundrect",
   "at": [
    2.475,
    -0.635
   ],
   "rot": 0.0,
   "size": [
    1.95,
    0.6
   ],
   "layers": [
    "F.Cu",
    "F.Mask",
    "F.Paste"
   ],
   "thermal": false,
   "pin": "7",
   "name": "WP",
   "type": "input",
   "description": "Write Protect input. Tie to GND for normal write operation; tie to VCC to inhibit all writes to the EEPROM array (hardware write protection). Internally pulled to GND if left floating and board-VCC coupling is <3 pF; Atmel recommends tying to GND when coupling is >3 pF.",
   "is_pin1": false,
   "source": {
    "geometry": "SOIC-8_3.9x4.9mm_P1.27mm.kicad_mod",
    "meaning": "page.json:component.pins",
    "correspondence": "kicad: symbol pin number == pad name"
   }
  },
  {
   "pad": "8",
   "kind": "smd",
   "shape": "roundrect",
   "at": [
    2.475,
    -1.905
   ],
   "rot": 0.0,
   "size": [
    1.95,
    0.6
   ],
   "layers": [
    "F.Cu",
    "F.Mask",
    "F.Paste"
   ],
   "thermal": false,
   "pin": "8",
   "name": "VCC",
   "type": "power_in",
   "description": "Positive supply, 1.7 V to 5.5 V. Standby current 1.0 uA typ @1.7V (6.0 uA @5.5V); read current 0.4 mA typ and write current 2.0 mA typ at VCC=5.0V, 400 kHz.",
   "is_pin1": false,
   "source": {
    "geometry": "SOIC-8_3.9x4.9mm_P1.27mm.kicad_mod",
    "meaning": "page.json:component.pins",
    "correspondence": "kicad: symbol pin number == pad name"
   }
  }
 ]
}