component
AT24C04D-XHM-T-TUDI
Public Made by Adomby adom
Tudi EEPROM, TSSOP-8. Pinout cross-checked by two models against the datasheet, KiCad symbol/footprint/3D.
Made with KiCad 10.0 · needs KiCad 10.0 or later to open · KiCad file format 20260206
| Name | Last updated |
|---|---|
| docs | 3d ago |
| viewers | 3d ago |
| at24c04d-xhm-t-tudi-etched.glb | 3d ago |
| at24c04d-xhm-t-tudi-etched.step | 3d ago |
| at24c04d-xhm-t-tudi-hero.glb | 3d ago |
| at24c04d-xhm-t-tudi-hero.overlay.json | 3d ago |
| at24c04d-xhm-t-tudi.glb | 3d ago |
| at24c04d-xhm-t-tudi.kicad_mod | 3d ago |
| at24c04d-xhm-t-tudi.kicad_sym | 3d ago |
| at24c04d-xhm-t-tudi.lbr | 3d ago |
| at24c04d-xhm-t-tudi.step | 3d ago |
| package.json | 3d ago |
| page.json | 3d ago |
| README.md | 3d ago |
AT24C04D-XHM-T-TUDI
Tudi · EEPROM · TSSOP-8
AT24C04D-XHM-T-TUDI from Tudi, in a TSSOP-8. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | A0 | unconnected | The datasheet states the A0 pin is no connect on the 4K (AT24C04) device, so it should not be driven or relied on for addressing. |
| 2 | A1 | input | Device address input hard-wired to the A1 device address bit, which must match the address bits on the 4K device; it is not a memory address pin. |
| 3 | A2 | input | Device address input hard-wired to the A2 device address bit; it must compare to its corresponding hard-wired pin for the device to respond. |
| 4 | GND | power_in | Ground reference for the device. |
| 5 | SDA | bidirectional | Bidirectional serial data pin that is open-drain driven, may be wire-ORed with other open-drain or open-collector devices, and is normally pulled high by an external device. |
| 6 | SCL | input | Serial clock input with Schmitt-trigger filtered inputs; data is clocked into the device on the positive edge and out on the negative edge, with bus speed up to 1MHz at 2.5V and above or 400kHz at 1.7V. |
| 7 | WP | input | Write protect input: connecting it to GND allows normal read/write operation, while connecting it to VCC enables write protection of the array as shown in Table 2. |
| 8 | VCC | power_in | Power supply, specified from 1.7V to 5.5V (absolute maximum DC supply −0.3V to +6.5V). |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Tudi |
| Package | TSSOP-8 |
| Category | Memory |
| Pins | 8 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| DC Supply Voltage | VCC | -0.3 | 6.5 | V | 10 | ||
| Operating Ambient Temperature | TA | -40 | 85 | ℃ | 10 | ||
| Storage Temperature | -65 | 150 | ℃ | 10 | |||
| Electrostatic pulse (Human Body model) | 8000 | V | Human Body model | 10 | |||
| Supply Voltage (recommended operating range) | VCC | 1.7 | 5.5 | V | 10 | ||
| Ambient Temperature (recommended operating range) | TA | -40 | 85 | ℃ | 10 | ||
| Output Low Level | VOL2 | 0.4 | V | VCC=5.0V, IOL=3.0mA | 10 | ||
| Output Low Level | VOL1 | 0.2 | V | VCC=1.7V, IOL=0.15mA | 10 | ||
| Input High Level | VIH1 | 0.7 | 0.3 | ×VCC | VCC=1.7V to 5.5V | 10 | |
| Input Low Level | VIL1 | -0.3 | 0.3 | V | VCC=1.7V to 5.5V | 10 | |
| Output Leakage Current | ILO | 0.05 | 1 | µA | VOUT=VCC or VSS | 10 | |
| Input Leakage Current | ILI | 0.1 | 1 | µA | VIN=VCC or VSS | 10 | |
| Standby Supply Current | ISB1 | 0.03 | 0.5 | µA | VCC=5.0V | 10 | |
| Supply Current (write) | ICC2 | 0.28 | 0.5 | mA | VCC=5.0V, WRITE at 400KHZ | 10 | |
| Supply Current (read) | ICC1 | 0.14 | 0.3 | mA | VCC=5.0V, READ at 400KHZ | 10 | |
| Supply Voltage (write range) | VCC2 | 2.5 | 5.5 | V | 10 | ||
| Supply Voltage (read range) | VCC1 | 1.7 | 5.5 | V | 10 | ||
| Input Capacitance (A0, A1, A2, SCL) | CIN | 6 | pF | TA=25℃, f=1.0 MHz, VCC=+1.7V, VIN=0V | 10 | ||
| Input/Output Capacitance (SDA) | CI/O | 8 | pF | VI/O=0V | 10 | ||
| Endurance (5.0V, 25℃, Byte Mode) | 1 | M cycles | 5.0V, 25℃, Byte Mode | 11 | |||
| Write Cycle Time | tWR | 1.9 | 3 | ms | 1.7V≤VCC<2.5V | 11 | |
| Data Out Hold Time | tDH | 50 | ns | 1.7V≤VCC<2.5V | 11 | ||
| Stop Setup Time | tSU:STO | 0.25 | µs | 1.7V≤VCC<2.5V | 11 | ||
| Input Fall Time | tF | 0.3 | µs | 1.7V≤VCC<2.5V | 11 | ||
| Input Rise Time | tR | 0.3 | µs | 1.7V≤VCC<2.5V | 11 | ||
| Data In Setup Time | tSU:DAT | 100 | ns | 1.7V≤VCC<2.5V | 11 | ||
| Data In Hold Time | tHD:DAT | 0 | µs | 1.7V≤VCC<2.5V | 11 | ||
| Start Setup Time | SU:STA | 0.25 | µs | 1.7V≤VCC<2.5V | 11 | ||
| Start Hold Time | tHD:STA | 0.25 | µs | 1.7V≤VCC<2.5V | 11 | ||
| Time the bus must be free before a new transmission can start | tBUF | 0.5 | µs | 1.7V≤VCC<2.5V | 11 | ||
| Clock Low to Data Out Valid | tAA | 0.1 | 0.55 | µs | 1.7V≤VCC<2.5V | 11 | |
| Noise Suppression Time | tI | 50 | ns | 1.7V≤VCC<2.5V | 11 | ||
| Clock Pulse Width High | tHIGH | 0.4 | µs | 1.7V≤VCC<2.5V | 11 | ||
| Clock Pulse Width Low | tLOW | 0.6 | µs | 1.7V≤VCC<2.5V | 11 | ||
| Clock Frequency, SCL | fSCL | 400 | KHZ | 1.7V≤VCC<2.5V | 11 | ||
| Clock Frequency, SCL | fSCL | 1000 | KHZ | 2.5V≤VCC<5.5V | 11 |
CAD (KiCad official)
- Symbol:
AT24C04D-XHM-T-TUDI - Footprint:
Package_SO:TSSOP-8_3x3mm_P0.65mm - 3D model: TSSOP-8 (KiCad packages3D, STEP)
- 3D model files:
at24c04d-xhm-t-tudi-etched.step/at24c04d-xhm-t-tudi-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);at24c04d-xhm-t-tudi.step/at24c04d-xhm-t-tudi.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Tudi datasheet (18 pp, sha256
4c16636c4866f117, retrieved 2026-10-18, tier: lcsc) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).