AT24C02C-STUM-T

{
 "schema": "adom.pads/1",
 "slug": "at24c02c-stum-t",
 "footprint": "SOT-23-5",
 "generated_from": {
  "footprint": "SOT-23-5@sha256:455a3f7c3e5eb5b8",
  "pins": "page.json:component.pins",
  "overrides": null
 },
 "pin1": {
  "pad": "1",
  "at": [
   -1.1375,
   -0.95
  ],
  "corner": "top-left",
  "source": "silk-marker",
  "derived_from": "SOT-23-5@sha256:455a3f7c3e5eb5b8"
 },
 "pad_count": 5,
 "symbol_pins": [
  "1",
  "2",
  "3",
  "4",
  "5"
 ],
 "paste_apertures": 0,
 "issues": [],
 "pads": [
  {
   "pad": "1",
   "kind": "smd",
   "shape": "roundrect",
   "at": [
    -1.1375,
    -0.95
   ],
   "rot": 0.0,
   "size": [
    1.325,
    0.6
   ],
   "layers": [
    "F.Cu",
    "F.Mask",
    "F.Paste"
   ],
   "thermal": false,
   "pin": "1",
   "name": "SCL",
   "type": "input",
   "description": "I²C serial clock input. Input data on SDA is latched on the rising edge; output data is clocked out on the falling edge. Requires external pull-up to VCC (or drive high) when the bus is idle.",
   "is_pin1": true,
   "source": {
    "geometry": "SOT-23-5.kicad_mod",
    "meaning": "page.json:component.pins",
    "correspondence": "kicad: symbol pin number == pad name"
   }
  },
  {
   "pad": "2",
   "kind": "smd",
   "shape": "roundrect",
   "at": [
    -1.1375,
    0.0
   ],
   "rot": 0.0,
   "size": [
    1.325,
    0.6
   ],
   "layers": [
    "F.Cu",
    "F.Mask",
    "F.Paste"
   ],
   "thermal": false,
   "pin": "2",
   "name": "GND",
   "type": "power_in",
   "description": "Ground reference for the power supply and I²C bus. Connect to system ground (0 V).",
   "is_pin1": false,
   "source": {
    "geometry": "SOT-23-5.kicad_mod",
    "meaning": "page.json:component.pins",
    "correspondence": "kicad: symbol pin number == pad name"
   }
  },
  {
   "pad": "3",
   "kind": "smd",
   "shape": "roundrect",
   "at": [
    -1.1375,
    0.95
   ],
   "rot": 0.0,
   "size": [
    1.325,
    0.6
   ],
   "layers": [
    "F.Cu",
    "F.Mask",
    "F.Paste"
   ],
   "thermal": false,
   "pin": "3",
   "name": "SDA",
   "type": "bidirectional",
   "description": "I²C serial data, open-drain bidirectional. Requires an external pull-up resistor to VCC (≤10 kΩ recommended); may be wire-ORed with other open-drain devices on the bus.",
   "is_pin1": false,
   "source": {
    "geometry": "SOT-23-5.kicad_mod",
    "meaning": "page.json:component.pins",
    "correspondence": "kicad: symbol pin number == pad name"
   }
  },
  {
   "pad": "4",
   "kind": "smd",
   "shape": "roundrect",
   "at": [
    1.1375,
    0.95
   ],
   "rot": 0.0,
   "size": [
    1.325,
    0.6
   ],
   "layers": [
    "F.Cu",
    "F.Mask",
    "F.Paste"
   ],
   "thermal": false,
   "pin": "4",
   "name": "VCC",
   "type": "power_in",
   "description": "Device power supply, 1.7 V to 5.5 V. Typical ICC ≈ 0.4 mA read / 2.0 mA write at 400 kHz (3 mA max active, 6 µA max standby).",
   "is_pin1": false,
   "source": {
    "geometry": "SOT-23-5.kicad_mod",
    "meaning": "page.json:component.pins",
    "correspondence": "kicad: symbol pin number == pad name"
   }
  },
  {
   "pad": "5",
   "kind": "smd",
   "shape": "roundrect",
   "at": [
    1.1375,
    -0.95
   ],
   "rot": 0.0,
   "size": [
    1.325,
    0.6
   ],
   "layers": [
    "F.Cu",
    "F.Mask",
    "F.Paste"
   ],
   "thermal": false,
   "pin": "5",
   "name": "WP",
   "type": "input",
   "description": "Write-Protect input. Tied to GND enables normal write operations; tied to VCC inhibits all writes to the full array. Internally pulled down to GND if floating; Microchip recommends driving to a known state (≤10 kΩ pull-up if used).",
   "is_pin1": false,
   "source": {
    "geometry": "SOT-23-5.kicad_mod",
    "meaning": "page.json:component.pins",
    "correspondence": "kicad: symbol pin number == pad name"
   }
  }
 ]
}