component
AP2111MPG-13
Public Made by Adomby adom
Diodes Incorporated Power Distribution Switches, MSOP-8-EP. Pinout cross-checked by two models against the datasheet, KiCad symbol/footprint/3D.
main
AP2111MPG-13
Diodes Incorporated · Power Distribution Switches · MSOP-8-EP
AP2111MPG-13 from Diodes Incorporated, in a MSOP-8-EP. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | GND | power_in | Ground pin; the exposed pad should be connected to GND and should not be used as the electrical ground conduction path. |
| 2 | IN | power_in | Voltage input pin; all IN pins must be tied together externally, with VIN recommended at 2.7 V to 5.5 V and an absolute maximum of 6.5 V. |
| 3 | IN | power_in | Voltage input pin; all IN pins must be tied together externally, with VIN recommended at 2.7 V to 5.5 V and an absolute maximum of 6.5 V. |
| 4 | EN | input | Enable input, active high on the AP2111; logic low is 0.8 V max and logic high is 2 V min, with absolute maximum VEN of 6.5 V. |
| 5 | FLG | output | Open-drain over-current and over-temperature fault flag, active low after a nominal 7 ms deglitch, with absolute maximum VFLG of 6.5 V. |
| 6 | OUT | power_out | Voltage output pin; all OUT pins must be tied together externally, and output current is limited to about 2.45 A typical (2.0 A recommended maximum continuous load). |
| 7 | OUT | power_out | Voltage output pin; all OUT pins must be tied together externally, and output current is limited to about 2.45 A typical (2.0 A recommended maximum continuous load). |
| 8 | NC | unconnected | No internal connection; the datasheet recommends tying this pin to the OUT pins. |
| 9 | EP | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Diodes Incorporated |
| Package | MSOP-8-EP |
| Category | Power Management (PMIC) |
| Pins | 9 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Input voltage | VIN | 2.7 | 5.5 | V | 3 | ||
| Output Current | IOUT | 0 | 2 | A | 3 | ||
| Operating Ambient Temperature | TA | -35 | 85 | °C | 3 | ||
| EN Input Logic Low Voltage | VIL | 0 | 0.8 | V | 3 | ||
| EN Input Logic High Voltage | VIH | 2 | V | 3 | |||
| Input UVLO | VUVLO | 1.6 | 1.9 | 2.5 | V | RLOAD = 1kΩ | 3 |
| Input Shutdown Current | ISHDN | 0.5 | 1 | µA | Disabled, IOUT = 0 | 3 | |
| Input Quiescent Current | IQ | 45 | 70 | µA | Enabled, IOUT = 0 | 3 | |
| Switch On-Resistance (MSOP8-EP) | RDS(ON) | 90 | 115 | mΩ | VIN = 5V, IOUT = 1.5A, TA = +25°C | 3 | |
| Switch On-Resistance | RDS(ON) | 140 | mΩ | VIN = 5V, IOUT = 1.5A, -40°C ≤ TA ≤ +85°C | 3 | ||
| Switch On-Resistance | RDS(ON) | 115 | 140 | mΩ | VIN = 3.3V, IOUT = 1.5A, TA = 25°C | 3 | |
| Switch On-Resistance | RDS(ON) | 170 | mΩ | VIN = 3.3V, IOUT = 1.5A, -40°C ≤ TA ≤ +85°C | 3 | ||
| Over-Load Current Limit | ILIMIT | 2.1 | 2.45 | 2.8 | A | VIN = 5V, VOUT = 4.5V, CL=120µF | 3 |
| EN Input Logic Low Voltage | VIL | 0.8 | V | VIN = 2.7V to 5.5V | 3 | ||
| EN Input Logic High Voltage | VIH | 2 | V | VIN = 2.7V to 5.5V | 3 | ||
| FLG Blanking Time | TBLANK | 4 | 7 | 15 | ms | CIN = 10µF, CL = 100µF | 3 |
| Output Turn-On Rise Time | TR | 0.6 | 1.5 | ms | CL = 1µF, RLOAD = 10Ω | 3 | |
| Output Turn-Off Fall Time | TF | 0.03 | 0.1 | ms | CL = 1µF, RLOAD = 10Ω | 3 | |
| FLG Output FET On-Resistance | RFLG | 20 | 40 | Ω | IFLG =10mA, CL=100µF | 3 | |
| ESD Protection, Human Body Model | ESD HBM | 4 | kV | Human Body Model | 2 | ||
| ESD Protection, Machine Model | ESD MM | 300 | V | Machine Model | 2 | ||
| Input Voltage | VIN | 6.5 | V | 2 | |||
| Enable and Flag Voltage | VEN, VFLG | 6.5 | V | 2 | |||
| Maximum Junction Temperature | TJ(MAX) | 150 | °C | 2 | |||
| Storage Temperature Range | TST | -65 | 150 | °C | Diodes qualified range (Note 4) | 2 |
CAD (KiCad official)
- Symbol:
AP2111MPG-13 - Footprint:
Package_SO:MSOP-8-1EP_3x3mm_P0.65mm_EP1.5x1.8mm - 3D model: MSOP-8-EP (KiCad packages3D, STEP)
- 3D model files:
ap2111mpg-13-etched.step/ap2111mpg-13-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);ap2111mpg-13.step/ap2111mpg-13.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Diodes Incorporated datasheet (14 pp, sha256
80525d55605821f1, retrieved 2026-10-18, tier: lcsc) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).
# AP2111MPG-13
**Diodes Incorporated** · Power Distribution Switches · MSOP-8-EP
AP2111MPG-13 from Diodes Incorporated, in a MSOP-8-EP. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
## Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | GND | power_in | Ground pin; the exposed pad should be connected to GND and should not be used as the electrical ground conduction path. |
| 2 | IN | power_in | Voltage input pin; all IN pins must be tied together externally, with VIN recommended at 2.7 V to 5.5 V and an absolute maximum of 6.5 V. |
| 3 | IN | power_in | Voltage input pin; all IN pins must be tied together externally, with VIN recommended at 2.7 V to 5.5 V and an absolute maximum of 6.5 V. |
| 4 | EN | input | Enable input, active high on the AP2111; logic low is 0.8 V max and logic high is 2 V min, with absolute maximum VEN of 6.5 V. |
| 5 | FLG | output | Open-drain over-current and over-temperature fault flag, active low after a nominal 7 ms deglitch, with absolute maximum VFLG of 6.5 V. |
| 6 | OUT | power_out | Voltage output pin; all OUT pins must be tied together externally, and output current is limited to about 2.45 A typical (2.0 A recommended maximum continuous load). |
| 7 | OUT | power_out | Voltage output pin; all OUT pins must be tied together externally, and output current is limited to about 2.45 A typical (2.0 A recommended maximum continuous load). |
| 8 | NC | unconnected | No internal connection; the datasheet recommends tying this pin to the OUT pins. |
| 9 | EP | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |
## Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Diodes Incorporated |
| Package | MSOP-8-EP |
| Category | Power Management (PMIC) |
| Pins | 9 |
## Electrical characteristics
Limits as printed in the datasheet (page.json `metadata.characteristics` carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Input voltage | VIN | 2.7 | | 5.5 | V | | 3 |
| Output Current | IOUT | 0 | | 2 | A | | 3 |
| Operating Ambient Temperature | TA | -35 | | 85 | °C | | 3 |
| EN Input Logic Low Voltage | VIL | 0 | | 0.8 | V | | 3 |
| EN Input Logic High Voltage | VIH | 2 | | | V | | 3 |
| Input UVLO | VUVLO | 1.6 | 1.9 | 2.5 | V | RLOAD = 1kΩ | 3 |
| Input Shutdown Current | ISHDN | | 0.5 | 1 | µA | Disabled, IOUT = 0 | 3 |
| Input Quiescent Current | IQ | | 45 | 70 | µA | Enabled, IOUT = 0 | 3 |
| Switch On-Resistance (MSOP8-EP) | RDS(ON) | | 90 | 115 | mΩ | VIN = 5V, IOUT = 1.5A, TA = +25°C | 3 |
| Switch On-Resistance | RDS(ON) | | | 140 | mΩ | VIN = 5V, IOUT = 1.5A, -40°C ≤ TA ≤ +85°C | 3 |
| Switch On-Resistance | RDS(ON) | | 115 | 140 | mΩ | VIN = 3.3V, IOUT = 1.5A, TA = 25°C | 3 |
| Switch On-Resistance | RDS(ON) | | | 170 | mΩ | VIN = 3.3V, IOUT = 1.5A, -40°C ≤ TA ≤ +85°C | 3 |
| Over-Load Current Limit | ILIMIT | 2.1 | 2.45 | 2.8 | A | VIN = 5V, VOUT = 4.5V, CL=120µF | 3 |
| EN Input Logic Low Voltage | VIL | | | 0.8 | V | VIN = 2.7V to 5.5V | 3 |
| EN Input Logic High Voltage | VIH | 2 | | | V | VIN = 2.7V to 5.5V | 3 |
| FLG Blanking Time | TBLANK | 4 | 7 | 15 | ms | CIN = 10µF, CL = 100µF | 3 |
| Output Turn-On Rise Time | TR | | 0.6 | 1.5 | ms | CL = 1µF, RLOAD = 10Ω | 3 |
| Output Turn-Off Fall Time | TF | | 0.03 | 0.1 | ms | CL = 1µF, RLOAD = 10Ω | 3 |
| FLG Output FET On-Resistance | RFLG | | 20 | 40 | Ω | IFLG =10mA, CL=100µF | 3 |
| ESD Protection, Human Body Model | ESD HBM | | | 4 | kV | Human Body Model | 2 |
| ESD Protection, Machine Model | ESD MM | | | 300 | V | Machine Model | 2 |
| Input Voltage | VIN | | | 6.5 | V | | 2 |
| Enable and Flag Voltage | VEN, VFLG | | | 6.5 | V | | 2 |
| Maximum Junction Temperature | TJ(MAX) | | | 150 | °C | | 2 |
| Storage Temperature Range | TST | -65 | | 150 | °C | Diodes qualified range (Note 4) | 2 |
## CAD (KiCad official)
- Symbol: `AP2111MPG-13`
- Footprint: `Package_SO:MSOP-8-1EP_3x3mm_P0.65mm_EP1.5x1.8mm`
- 3D model: MSOP-8-EP (KiCad packages3D, STEP)
- 3D model files: `ap2111mpg-13-etched.step` / `ap2111mpg-13-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `ap2111mpg-13.step` / `ap2111mpg-13.glb` are the bare package body.
## Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- **Datasheet:** [Diodes Incorporated datasheet](https://jlcpcb.com/api/file/downloadByFileSystemAccessId/8590458461805969408) (14 pp, sha256 `80525d55605821f1`, retrieved 2026-10-18, tier: lcsc)
- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.3`, primary `claude-haiku-5-5` (text), consensus `claude-sonnet-5-5` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
- **CAD:** KiCad official libraries (CC-BY-SA 4.0).
[Datasheet PDF](docs/ap2111mpg-13-datasheet.pdf)