component
AL8116W6-7
Public Made by Adomby adom
Diodes Incorporated LED Drivers, SOT-26. Pinout cross-checked by two models against the datasheet, KiCad symbol/footprint/3D.
Generated by kicad-footprint-generator · KiCad file format 20260206
| Name | Last updated |
|---|---|
| docs | 9d ago |
| viewers | 9d ago |
| al8116w6-7-etched.glb | 9d ago |
| al8116w6-7-etched.step | 9d ago |
| al8116w6-7-hero.glb | 9d ago |
| al8116w6-7-hero.overlay.json | 9d ago |
| al8116w6-7.glb | 9d ago |
| al8116w6-7.kicad_mod | 9d ago |
| al8116w6-7.kicad_sym | 9d ago |
| al8116w6-7.lbr | 9d ago |
| al8116w6-7.step | 9d ago |
| package.json | 9d ago |
| page.json | 9d ago |
| README.md | 9d ago |
AL8116W6-7
Diodes Incorporated · LED Drivers · SOT-26
AL8116W6-7 from Diodes Incorporated, in a SOT-26. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | VCC | power_in | Supply voltage pin; recommended VCC is 10 V to 56 V, and a 0.1 µF to 0.47 µF SMD ceramic capacitor should be placed as close to the IC as possible to filter switching noise. |
| 2 | GND | power_in | Ground or power return pin; all voltages in the datasheet are measured with respect to GND. |
| 3 | OUT | output | Dimming PWM output in open-drain configuration, connected to the power supply through a resistor; recommended sink current is up to 20 mA, with absolute maximum 30 mA and voltage up to 56 V. |
| 4 | ISET | passive | Sets the DIM pin bias current through resistor RISET to GND, with RISET recommended between 33 kΩ and 330 kΩ and an absolute maximum voltage of -0.3 V to +6 V. |
| 5 | CLAMP | passive | Sets the minimum output duty clamp through resistor RCLAMP to GND (0 Ω gives 8%, 150 kΩ gives 6%, 300 kΩ gives 4%, open gives no clamp), with an absolute maximum voltage of -0.3 V to +6 V. |
| 6 | DIM | input | Dimming signal input accepting 0/1 V to 10 V DC, PWM at 0.2 kHz to 10 kHz with high level at or above 3.2 V, or a potentiometer to GND; absolute maximum voltage is -0.3 V to +20 V. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Diodes Incorporated |
| Package | SOT-26 |
| Category | LED Drivers |
| Pins | 6 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Voltage at VCC Pin (supply) | VCC | 10 | 56 | V | 4 | ||
| Input Voltage on OUT Pin | VOUT | 56 | V | 4 | |||
| Operating Junction Temperature | TJ | -40 | 125 | °C | 4 | ||
| Resistor of ISET Pin | RISET | 33 | 330 | kΩ | 4 | ||
| Source Current of DIM Pin | IDIM_SOURCE | 300 | μA | 4 | |||
| Input Voltage of DIM Pin | VDIM | 0 | 13 | V | 4 | ||
| Input PWM Frequency of DIM Pin | fDIM | 0.5 | 5 | kHz | 4 | ||
| Capacitor of DIM Pin (CDIM) | CDIM | 330 | 1000 | pF | Note 7 (RISET = 100kΩ) | 4 | |
| Resistance of DIM Pin (RDIM) | RDIM | 1 | 6.5 | kΩ | Note 7 (RISET = 100kΩ) | 4 | |
| PWM Signal Input Rising and Falling Time Rate | 3 | V/μs | 4 | ||||
| High Voltage Level PWM Signal Input on DIM Pin | VDIM_PWM_H | 3.2 | 13 | V | 4 | ||
| Low Voltage Level PWM Signal Input on DIM Pin | VDIM_PWM_L | 1.2 | V | 4 | |||
| Sink Current of OUT Pin | IOUT_SINK | 20 | mA | 4 | |||
| Ambient Temperature | TA | -40 | 105 | °C | 4 | ||
| SMD ceramic capacitor on VCC pin (filter for switching noise) | 0.1 | 0.47 | μF | Note 6: place as close to IC as possible | 4 | ||
| Voltage at VCC Pin | VCC | -0.3 | 60 | V | 4 | ||
| Voltage at OUT Pin | VOUT | -0.3 | 60 | V | 4 | ||
| OUT Sink Current | IOUT | 30 | mA | 4 | |||
| Voltage at DIM Pin | VDIM | -0.3 | 20 | V | 4 | ||
| Voltages at ISET, CLAMP Pins | VISET, VCLAMP | -0.3 | 6 | V | 4 | ||
| Lead Temperature (Soldering) | TLEAD | 260 | °C | Soldering, 10s | 4 | ||
| Operating Junction Temperature | TJ | -40 | 150 | °C | 4 | ||
| Storage Temperature | TST | -65 | 150 | °C | 4 | ||
| ESD (Human Body Model) | 2.5 | kV | Human Body Model | 4 | |||
| ESD (Charged-Device Model) | 1000 | V | Charged-Device Model | 4 | |||
| Supply VCC Voltage (UVLO ON threshold) | VCC_ON | 6 | 7 | 8 | V | 5 | |
| Minimum Operating Voltage (UVLO OFF threshold) | VCC_OFF | 5.2 | 6 | 6.8 | V | 5 | |
| Operating Current | IVCC | 600 | 850 | μA | RISET = 100kΩ, DIM Pin and CLAMP Pin are Floating. | 5 | |
| Open Voltage (ISET Pin) | VISET_OPEN | 2.45 | 2.5 | 2.55 | V | ISET Pin is Floating. | 5 |
| Open Voltage (DIM Pin) | VDIM_OPEN | 12.2 | 13 | 13.8 | V | RISET = 100kΩ, DIM Pin is Floating. | 5 |
| Maximum Voltage on Level (DIM Pin) | VDIM_MAX_ON | 10.07 | 10.27 | 10.47 | V | Output Duty = 100% | 5 |
| Bias Current | IDIM_100 | 97.5 | 100.5 | 103.5 | μA | RISET = 100kΩ | 5 |
| High Level of PWM Input Signal | VDIM_PWM_H | 3.2 | V | Note 8 | 5 | ||
| Low Level of PWM Input Signal | VDIM_PWM_L | 1.2 | V | Note 8 | 5 | ||
| PWM Dimming Mode Setting Trigger Rising Rate and Continuous 8 Times | 3 | V/μs | Note 8 | 5 | |||
| Cut-Off Level Voltage | VDIM_OFF | 1.23 | 1.3 | 1.37 | V | Output Duty = 0% | 5 |
| Open Voltage (CLAMP Pin) | VCLAMP_OPEN | 4.7 | 5 | 5.3 | V | RISET = 100kΩ, CLAMP Pin is Floating. | 5 |
| Minimum Duty Cycle Clamp (0% setting) | DOUT_0% | 1 | 2 | 4 | % | When RISET = 100kΩ; RCLAMP ≧ 1MΩ or Open; VCLAMP ≧ 4.2V and VDIM = 1.65V | 5 |
| Minimum Duty Cycle Clamp (4% setting) | DOUT_4% | 2 | 4 | 6 | % | RCLAMP = 300kΩ; VCLAMP = 2.6V to 3.6V and VDIM = 1.5V | 5 |
| Minimum Duty Cycle Clamp (6% setting) | DOUT_6% | 4 | 6 | 8 | % | RCLAMP = 150kΩ; VCLAMP = 1V to 2V and VDIM = 1.5V | 5 |
| Minimum Duty Cycle Clamp (8% setting) | DOUT_8% | 6 | 8 | 10 | % | RCLAMP = 0Ω; VCLAMP ≦ 0.5V and VDIM = 1.5V | 5 |
| Output Low Level | VOUT_LOW | 200 | mV | @2mA Sink Current | 5 | ||
| Dimming Accuracy of Duty (Chip to Chip) | D. A | -2.5 | 2.5 | % | During DIM Voltage is from 2V to 9V. (Note 8) | 5 | |
| Output Frequency | fOUT | 1 | 1.5 | 2 | kHz | 5 | |
| Current Ratio of IDIM to ISET | KDIM | 4 | , | Calculate IDIM / ISET | 5 | ||
| Current Ratio of ICLAMP to ISET | KCLAMP | 0.4 | , | Calculate ICLAMP / ISET | 5 | ||
| Zero Duty On Level (DIM Pin) | VDIM_Zero_ON | 1.5 | V | Output Duty ≦ 1% | 5 | ||
| Cut-Off Recovery Hysteresis Voltage | VDIM_OFF_HYS | 0.1 | V | Output Duty ≥ 0% | 5 | ||
| OTP Trip Level | OTP | 135 | °C | Note 8 | 5 | ||
| OTP Hysteresis | ΔOTP | 20 | °C | Note 8 | 5 | ||
| Thermal Resistance Junction-to-Case | θJC | 60 | °C/W | SOT26 (Type CJ); Note 5: 1in x 1in FR-4 PCB, 2oz copper, minimum recommended pad layout | 4 | ||
| Thermal Resistance Junction-to-Ambient | θJA | 240 | °C/W | SOT26 (Type CJ); Note 5: 1in x 1in FR-4 PCB, 2oz copper, minimum recommended pad layout | 4 | ||
| Power Dissipation | PD | 200 | mW | SOT26 (Type CJ); TA = +85°C | 4 |
Materials and finish
As the datasheet states them (page.json metadata.appearance; the 3D model's colours follow it).
| Part | Material | Colour / plating | Datasheet says | Page |
|---|---|---|---|---|
| contacts | tin | Terminals: Finish - Matte Tin Plated Leads, Solderable per M2003 JESD22-B102 Weight: 0.016 grams (Approximate) | 12 |
CAD (KiCad official)
- Symbol:
AL8116W6-7 - Footprint:
Package_TO_SOT_SMD:SOT-23-6 - 3D model: SOT-26 (KiCad packages3D, STEP)
- 3D model files:
al8116w6-7-etched.step/al8116w6-7-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);al8116w6-7.step/al8116w6-7.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Diodes Incorporated datasheet (13 pp, sha256
2660a34929ecafe1, retrieved 2026-10-17, tier: lcsc) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).