component
ADS8528SPM
Public Made by Adomby adom
Texas Instruments Analog To Digital Converters (ADCs), LQFP-64(10x10). Pinout cross-checked by two models against the datasheet, KiCad symbol/footprint/3D.
Generated by kicad-footprint-generator · KiCad file format 20260206
ADS8528SPM
Texas Instruments · Analog To Digital Converters (ADCs) · LQFP-64(10x10)
ADS8528SPM from Texas Instruments, in a LQFP-64(10x10). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model). Symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | HVSS | power_in | Negative supply voltage for the analog inputs; decouple according to the Power Supply Recommendations section. |
| 2 | CH_D1 | input | Analog input of channel D1; the input voltage range is set by the RANGE pin in hardware mode or by CONFIG bit C19 (RANGE_D) in software mode, and the pin can be powered down with CONFIG bit C18 (PD_D). |
| 3 | REFDN | input | Decoupling capacitor input for the channel pair D reference; connect to the decoupling capacitor and AGND according to the Power Supply Recommendations section. |
| 4 | AVDD | power_in | Analog power supply; decouple according to the Power Supply Recommendations section. |
| 5 | AGND | power_in | Analog ground; connect to the analog ground plane. |
| 6 | REFDP | input | Decoupling capacitor input for the channel pair D reference; connect to the decoupling capacitor according to the Power Supply Recommendations section. |
| 7 | CH_D0 | input | Analog input of channel D0; the input voltage range is set by the RANGE pin in hardware mode or by CONFIG bit C19 (RANGE_D) in software mode, and the pin can be powered down with CONFIG bit C18 (PD_D). |
| 8 | PAR/SER | input | Interface mode selection input; when low the parallel interface is selected, and when high the serial interface is enabled. |
| 9 | STBY | input | In hardware mode, low powers the entire device down (including the internal conversion clock and reference) and high gives normal operation; in software mode, connect to DGND or DVDD and use CONFIG bit C25 (STBY). |
| 10 | RESET | input | Active-high reset input that aborts ongoing conversions and resets CONFIG to 000003FFh; a valid reset pulse must be at least 50 ns long. |
| 11 | REFEN/WR | input | In hardware mode, high enables the internal reference and its buffers and low requires an external reference at REFIO; in software mode it is the write input (parallel data enabled when CS and WR are low) and the internal reference is set by CONFIG bit C15 (REFEN). |
| 12 | RD | input | Read data input; when low the parallel data output is enabled (if CS = 0), and this pin must be connected to DGND. |
| 13 | CS/FS | input | Chip-select input (low enables the parallel interface, high disables it); in serial mode this pin is the frame synchronization input, where the FS falling edge controls the frame transfer. |
| 14 | AVDD | power_in | Analog power supply; decouple according to the Power Supply Recommendations section. |
| 15 | AGND | power_in | Analog ground; connect to the analog ground plane. |
| 16 | DB15/SDO_D | bidirectional | Data bit 15 (MSB) input/output; sign extension output for the ADS8528 and ADS8548; when SEL_CD = 1 it is the data output for channel pair D, and when SEL_CD = 0 it must be tied to DGND. |
| 17 | DB14/SDO_C | bidirectional | Data bit 14 input/output; sign extension output for the ADS8528 and ADS8548; when SEL_CD = 1 it is the data output for channel pair C, and when SEL_CD = 0 it must be tied to DGND. |
| 18 | DB13/SDO_B | bidirectional | Data bit 13 input/output; sign extension output for the ADS8528 and MSB for the ADS8548; when SEL_B = 1 it is the data output for channel pair B, and when SEL_B = 0 it must be tied to DGND. |
| 19 | DB12/SDO_A | bidirectional | Data bit 12 input/output; sign extension output for the ADS8528 and data output for channel pair A; when SEL_CD = 0 and SEL_B = 0 it is the single data output for all eight channels. |
| 20 | DB11/REFBUFEN | bidirectional | Data bit 11 input/output, the MSB output for the ADS8528; in hardware mode a low on REFBUFEN enables all internal reference buffers (mandatory if the internal reference is used), and in software mode it must be connected to DGND or DVDD with buffers controlled by CONFIG bit C14. |
| 21 | DB10/SCLK | bidirectional | Data bit 10 input/output; serial interface clock input. |
| 22 | DB9/SDI | bidirectional | Data bit 9 input/output; in hardware mode it must be connected to DGND, and in software mode it is the serial data input. |
| 23 | DB8/DCEN | bidirectional | Data bit 8 input/output; daisy-chain enable input that, when high, makes DB[3:0] the daisy-chain inputs DCIN_[A:D], and connect to DGND if daisy-chain mode is not used. |
| 24 | DGND | power_in | Buffer I/O ground; connect to the digital ground plane. |
| 25 | DVDD | power_in | Buffer I/O supply; connect to the digital supply and decouple according to the Power Supply Recommendations section. |
| 26 | DB7 | bidirectional | Data bit 7 input/output; must be connected to DGND. |
| 27 | DB6/SEL_B | bidirectional | Data bit 6 input/output; select SDO_B input: when low SDO_B is disabled and all eight channels are only available on SDO_A, and when high (with SEL_CD = 0) channel pairs B and D are on SDO_B, or with SEL_CD = 1 only channel pair B is on SDO_B. |
| 28 | DB5/SEL_CD | bidirectional | Data bit 5 input/output; select SDO_C and SDO_D input: when high, pair C is on SDO_C and pair D is on SDO_D; when low with SEL_B = 1, pairs A and C are on SDO_A and pairs B and D are on SDO_B; when low with SEL_B = 0, all eight channels are on SDO_A. |
| 29 | DB4 | bidirectional | Data bit 4 input/output; connect to DGND. |
| 30 | DB3/DCIN_A | bidirectional | Data bit 3 input/output; when DCEN = 1 it is the daisy-chain data input for SDO_A of the previous device, and when DCEN = 0 it must be connected to DGND. |
| 31 | DB2/DCIN_B | bidirectional | Data bit 2 input/output; when DCEN = 1 and SEL_B = 1 it is the daisy-chain data input for SDO_B of the previous device, and when DCEN = 0 it must be connected to DGND. |
| 32 | DB1/DCIN_C | bidirectional | Data bit 1 input/output; when DCEN = 1 and SEL_CD = 1 it is the daisy-chain data input for SDO_C of the previous device, and when DCEN = 0 it must be connected to DGND. |
| 33 | DB0/DCIN_D | bidirectional | Data bit 0 (LSB) input/output; when DCEN = 1 and SEL_CD = 1 it is the daisy-chain data input for SDO_D of the previous device, and when DCEN = 0 it must be connected to DGND. |
| 34 | RANGE/XCLK | bidirectional | In hardware mode, selects the analog input range (low = ±4 VREF, high = ±2 VREF); in software mode it is the external conversion clock input if CONFIG C29 (CLKSEL) = 1 or the internal conversion clock output if C28 (CLKOUT_EN) = 1; connect to DGND if unused. |
| 35 | BUSY/INT | output | With CONFIG bit C27 = 0 it is the converter busy status output (high on conversion start, one tCCLK low pulse per completed channel pair); with C27 = 1 it is an interrupt output that stays high until the next read and can only be used when all CONVST_x inputs are tied together; polarity is set by C26. |
| 36 | ASLEEP | input | Auto-sleep enable input; low selects normal mode, and high selects auto-sleep mode where hold and conversion start six tCCLK cycles after a CONVST_x. |
| 37 | CONVST_A | input | Conversion start for channel pair A; its rising edge starts simultaneous conversion of CH_A[1:0] and resets the channel state machine so the next read returns channel A0 first. |
| 38 | CONVST_B | input | Conversion start for channel pair B; its rising edge starts simultaneous conversion of CH_B[1:0]. |
| 39 | CONVST_C | input | Conversion start for channel pair C; its rising edge starts simultaneous conversion of CH_C[1:0]. |
| 40 | CONVST_D | input | Conversion start for channel pair D; its rising edge starts simultaneous conversion of CH_D[1:0]. |
| 41 | HW/SW | input | Mode selection input; when low hardware mode is selected and the device follows the external pins, and when high software mode is selected and the device is configured through the CONFIG register. |
| 42 | CH_A0 | input | Analog input of channel A0; channel A is the master pair that is always active, its range is set by the RANGE pin or CONFIG bit C24 (RANGE_A), and pair A must run at the highest data rate when pairs run at different rates. |
| 43 | REFAP | input | Decoupling capacitor input for the channel pair A reference; connect to the decoupling capacitor according to the Power Supply Recommendations section. |
| 44 | AGND | power_in | Analog ground; connect to the analog ground plane. |
| 45 | AVDD | power_in | Analog power supply; decouple according to the Power Supply Recommendations section. |
| 46 | REFAN | input | Decoupling capacitor input for the channel pair A reference; connect to the decoupling capacitor and AGND according to the Power Supply Recommendations section. |
| 47 | CH_A1 | input | Analog input of channel A1; channel A is the master pair that is always active, its range is set by the RANGE pin or CONFIG bit C24 (RANGE_A), and pair A must run at the highest data rate when pairs run at different rates. |
| 48 | HVDD | power_in | Positive supply voltage for the analog inputs; decouple according to the Power Supply Recommendations section. |
| 49 | CH_B0 | input | Analog input of channel B0; the input voltage range is set by the RANGE pin in hardware mode or by CONFIG bit C23 (RANGE_B) in software mode. |
| 50 | REFBP | input | Decoupling capacitor input for the channel pair B reference; connect to the decoupling capacitor according to the Power Supply Recommendations section. |
| 51 | AGND | power_in | Analog ground; connect to the analog ground plane. |
| 52 | AVDD | power_in | Analog power supply; decouple according to the Power Supply Recommendations section. |
| 53 | REFBN | input | Decoupling capacitor input for the channel pair B reference; connect to the decoupling capacitor and AGND according to the Power Supply Recommendations section. |
| 54 | CH_B1 | input | Analog input of channel B1; the input voltage range is set by the RANGE pin in hardware mode or by CONFIG bit C23 (RANGE_B) in software mode. |
| 55 | REFN | input | Negative reference input/output; connect to a decoupling capacitor and AGND according to the Power Supply Recommendations section. |
| 56 | REFIO | bidirectional | Reference voltage input/output; the internal reference is enabled by REFEN/WR (hardware mode) or CONFIG bit C15 (software mode), its output value is set by the internal DAC through CONFIG bits C[9:0], and it requires a decoupling capacitor per the Power Supply Recommendations section. |
| 57 | AVDD | power_in | Analog power supply; decouple according to the Power Supply Recommendations section. |
| 58 | AGND | power_in | Analog ground; connect to the analog ground plane. |
| 59 | CH_C1 | input | Analog input of channel C1; the input voltage range is set by the RANGE pin in hardware mode or by CONFIG bit C21 (RANGE_C) in software mode. |
| 60 | REFCN | input | Decoupling capacitor input for the channel pair C reference; connect to the decoupling capacitor and AGND according to the Power Supply Recommendations section. |
| 61 | AVDD | power_in | Analog power supply; decouple according to the Power Supply Recommendations section. |
| 62 | AGND | power_in | Analog ground; connect to the analog ground plane. |
| 63 | REFCP | input | Decoupling capacitor input for the channel pair C reference; connect to the decoupling capacitor according to the Power Supply Recommendations section. |
| 64 | CH_C0 | input | Analog input of channel C0; the input voltage range is set by the RANGE pin in hardware mode or by CONFIG bit C21 (RANGE_C) in software mode. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Texas Instruments |
| Package | LQFP-64(10x10) |
| Category | Data Converters |
| Pins | 64 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Supply voltage HVDD to AGND | -0.3 | 18 | V | 9 | |||
| Supply voltage HVSS to AGND | -18 | 0.3 | V | 9 | |||
| Supply voltage AVDD to AGND | -0.3 | 6 | V | 9 | |||
| Supply voltage DVDD to DGND | -0.3 | 6 | V | 9 | |||
| Ground voltage difference AGND to DGND | -0.3 | 0.3 | V | 9 | |||
| Input current to all pins except supply | -10 | 10 | mA | 9 | |||
| Maximum virtual junction temperature | TJ | 150 | °C | 9 | |||
| Storage temperature | Tstg | -65 | 150 | °C | 9 | ||
| AVDD Analog supply voltage | AVDD | 4.5 | 5 | 5.5 | V | 9 | |
| DVDD Buffer I/O supply voltage | DVDD | 2.7 | 3.3 | 5.5 | V | 9 | |
| HVDD Input positive supply voltage | HVDD | 5 | 15 | 16.5 | V | 9 | |
| HVSS Input negative supply voltage | HVSS | -16.5 | -15 | -5 | V | 9 | |
| TA Operating ambient temperature range | TA | -40 | 25 | 125 | °C | 9 | |
| Junction-to-ambient thermal resistance (PM LQFP 64) | RθJA | 48.5 | °C/W | PM (LQFP) 64 pins | 9 | ||
| Junction-to-case (top) thermal resistance (PM LQFP 64) | RθJC(top) | 9.4 | °C/W | PM (LQFP) 64 pins | 9 | ||
| Junction-to-board thermal resistance (PM LQFP 64) | RθJB | 21.9 | °C/W | PM (LQFP) 64 pins | 9 | ||
| Junction-to-top characterization parameter (PM LQFP 64) | ψJT | 0.3 | °C/W | PM (LQFP) 64 pins | 9 | ||
| Junction-to-board characterization parameter (PM LQFP 64) | ψJB | 21.4 | °C/W | PM (LQFP) 64 pins | 9 | ||
| Input leakage current | -1 | 1 | μA | No ongoing conversion | 10 | ||
| Reference voltage, 2.5-V operation | VREF | 2.485 | 2.5 | 2.515 | V | 2.5-V operation, REFDAC = 3FFh | 10 |
| Reference voltage, 2.5-V operation at 25°C | VREF | 2.496 | 2.5 | 2.504 | V | 2.5-V operation, REFDAC = 3FFh at 25°C | 10 |
| Reference voltage, 3.0-V operation | VREF | 2.985 | 3 | 3.015 | V | 3.0-V operation, REFDAC = 3FFh | 10 |
| Reference voltage, 3.0-V operation at 25°C | VREF | 2.995 | 3 | 3.005 | V | 3.0-V operation, REFDAC = 3FFh at 25°C | 10 |
| Reference voltage drift | dVREF/dT | -10 | 10 | ppm/°C | 10 | ||
| Reference output current | IREFOUT | -2 | 2 | mA | At dc current | 10 | |
| External load capacitance at REF_xP, REF_xN pins | 4.7 | 10 | μF | At REF_xP, REF_xN pins | 10 | ||
| External load capacitance at REFIO pin | 100 | 470 | nF | At REFIO pin | 10 | ||
| REFDAC differential nonlinearity | DNLDAC | -1 | 0.1 | 1 | LSB | 10 | |
| REFDAC integral nonlinearity | INLDAC | -2 | 0.1 | 2 | LSB | 10 | |
| REFDAC offset error | VOSDAC | -4 | 0.65 | 4 | LSB | VREF = 0.5 V (DAC = 0CDh) | 10 |
| Reference input voltage | VREFIN | 0.5 | 2.5 | 3.025 | V | 10 | |
| Digital input current | -50 | 50 | nA | VI = DVDD to DGND | 10 | ||
| High-impedance-state output current | -50 | 50 | nA | 10 | |||
| Analog supply current, ADS8528 | IAVDD | 37.9 | 50.1 | mA | ADS8528, fDATA = maximum | 11 | |
| Analog supply current, auto-sleep | IAVDD | 20.3 | 30 | mA | fDATA = 250 kSPS, auto-sleep mode | 11 | |
| Buffer I/O supply current | IDVDD | 0.5 | 2 | mA | fDATA = maximum | 11 | |
| Buffer I/O supply current, 250 kSPS | IDVDD | 0.5 | 1.4 | mA | fDATA = 250 kSPS | 11 | |
| Input positive supply current, ADS8528 | IHVDD | 3 | 4.2 | mA | ADS8528, fDATA = maximum | 11 | |
| Input positive supply current, 250 kSPS | IHVDD | 1.8 | 2.4 | mA | fDATA = 250 kSPS | 11 | |
| Input negative supply current, ADS8528 | IHVSS | 3.4 | 4.5 | mA | ADS8528, fDATA = maximum | 12 | |
| Input negative supply current, 250 kSPS | IHVSS | 2.1 | 2.6 | mA | fDATA = 250 kSPS | 12 | |
| Power dissipation, ADS8528 | 287.1 | 430.1 | mW | ADS8528, fDATA = maximum; footnote 3: HVDD = 15 V, HVSS = -15 V | 12 | ||
| Power dissipation, auto-sleep 250 kSPS | 161.7 | 255.2 | mW | fDATA = 250 kSPS, auto-sleep mode; footnote 3: HVDD = 15 V, HVSS = -15 V | 12 | ||
| Integral linearity error (ADS8528) | INL | -0.75 | 0.2 | 0.75 | LSB | 13 | |
| Differential linearity error (ADS8528) | DNL | -0.5 | 0.2 | 0.5 | LSB | 13 | |
| Offset error (ADS8528) | -1.5 | 0.5 | 1.5 | mV | 13 | ||
| Offset error matching (ADS8528) | -0.65 | 0.65 | mV | 13 | |||
| Offset error drift (ADS8528) | -3.5 | 3.5 | μV/°C | 13 | |||
| Gain error (ADS8528) | -0.5 | 0.25 | 0.5 | % | Referenced to voltage at REFIO | 13 | |
| Gain error matching between channels of any pair (ADS8528) | -0.2 | 0.2 | % | Between channels of any pair | 13 | ||
| Gain error matching between any two channels (ADS8528) | -0.4 | 0.4 | % | Between any two channels | 13 | ||
| Gain error drift (ADS8528) | -6 | 6 | ppm/°C | Referenced to voltage at REFIO | 13 | ||
| Signal-to-noise ratio (ADS8528) | SNR | 73 | 73.9 | dB | At fIN = 10 kHz | 13 | |
| Signal-to-noise ratio + distortion (ADS8528) | SINAD | 73 | 73.8 | dB | At fIN = 10 kHz | 13 | |
| Spurious-free dynamic range (ADS8528) | SFDR | 84 | 92 | dB | At fIN = 10 kHz | 13 |
CAD (KiCad official)
- Symbol:
ADS8528SPM - Footprint:
Package_QFP:LQFP-64_10x10mm_P0.5mm - 3D model: LQFP-64(10x10) (KiCad packages3D, STEP)
- 3D model files:
ads8528spm-etched.step/ads8528spm-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);ads8528spm.step/ads8528spm.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Texas Instruments datasheet (61 pp, sha256
dee84e8a5c9a2860, retrieved 2026-11-13, tier: manufacturer) - Datasheet language: Chinese. Pin names, descriptions, and specs on this page were extracted and translated to English by ds2sf; the linked PDF is the manufacturer original.
- Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).