← Commit history

Initial commit: component/ads127l01ipbs

Ray ·d32fb3726a ·
2 files changed +371
README.mdadded+69
@@ -0,0 +1,69 @@+# ADS127L01IPBS++**Texas Instruments** · Analog To Digital Converters (ADC) · TQFP-32(5x5)++ADS127L01IPBS from Texas Instruments, in a TQFP-32(5x5). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.++## Pinout++| Pin | Name | Type | Function |+|---|---|---|---|+| 1 | LVDD | power_out | 1.8-V analog supply from internal LDO regulator (INTLDO=0) or input (INTLDO=1); decouple with 1-µF capacitor to AGND. |+| 2 | CAP1 | output | Modulator common-mode voltage output; connect a 1-µF capacitor to AGND. |+| 3 | AINN | input | Negative differential analog input for ADC measurement (range AGND-0.3V to AVDD+0.3V). |+| 4 | AINP | input | Positive differential analog input for ADC measurement (range AGND-0.3V to AVDD+0.3V). |+| 5 | AGND | power_in | Analog ground reference. |+| 6 | AVDD | power_in | Analog-supply voltage input (2.7V to 3.6V); connect a 1-µF capacitor to AGND. |+| 7 | REXT | input | Analog power-scaling bias resistor pin; connect 60.4-kΩ resistor (HR/LP modes) or 120-kΩ (VLP mode) to AGND. |+| 8 | INTLDO | input | LVDD voltage selection pin; pull high to AVDD (external 1.8-V supply) or low to AGND (internal LDO) through 10-kΩ resistor. |+| 9 | REFP | input | Positive analog reference input; connect minimum 10-µF capacitor between REFP and REFN. |+| 10 | REFN | input | Negative analog reference input. |+| 11 | CAP2 | output | Reference common-mode voltage output; connect a 1-µF capacitor to AGND. |+| 12 | FILTER1 | input | Digital filter select pin bit 1; pull high to DVDD or low to DGND through 100-kΩ resistor. |+| 13 | FILTER0 | input | Digital filter select pin bit 0; pull high/low through 100-kΩ resistor; 00=WB1, 01=WB2, 10=LL, 11=Reserved. |+| 14 | FSMODE | input | Frame-sync mode select pin; pull high (master mode) or low (slave mode) through 100-kΩ resistor; applies to Frame-Sync interface only. |+| 15 | OSR1 | input | Oversampling ratio select pin bit 1 for decimation filters; pull high/low through 100-kΩ resistor. |+| 16 | OSR0 | input | Oversampling ratio select pin bit 0; pull high/low through 100-kΩ resistor; wideband filters 00=32x, 01=64x, 10=128x, 11=256x. |+| 17 | START | input | Synchronization signal (active high) to start or restart ADC conversion. |+| 18 | DAISYIN | input | Daisy-chain input for cascaded device configurations; tie directly to DGND if not daisy-chaining. |+| 19 | DRDY/FSYNC | bidirectional | SPI interface: data ready output (active low); Frame-sync interface: frame-sync input signal for synchronization. |+| 20 | DOUT | output | Serial data output from ADC (24-bit or 32-bit format); high-impedance when CS=1 in cascaded SPI configurations. |+| 21 | DIN | input | Serial data input for SPI interface; tie directly to DGND when using frame-sync interface mode. |+| 22 | SCLK | bidirectional | Serial clock input for SPI interface (0 to DVDD+0.3V); functions as input/output depending on interface configuration. |+| 23 | CS | input | Chip select input (active high in SPI cascaded configurations); tie directly to DGND when using frame-sync interface; controls DOUT tri-state. |+| 24 | CLK | input | Master clock input for internal timing and ADC modulator operation. |+| 25 | CAP3 | output | Internally-generated digital operating voltage output; connect a 1-µF capacitor to DGND. |+| 26 | DGND | power_in | Digital ground reference. |+| 27 | DVDD | power_in | Digital-supply voltage input (1.7V to 3.6V); connect a 1-µF capacitor to DGND. |+| 28 | RESET/PWDN | input | Reset or power-down pin (active low); asynchronous reset of all registers when pulled low. |+| 29 | HR | input | ADC operating mode select; pull high to DVDD (high-resolution mode) or low to DGND (LP/VLP mode) through 100-kΩ resistor. |+| 30 | FORMAT | input | Interface protocol select; pull high to DVDD (Frame-Sync mode) or low to DGND (SPI mode) through 100-kΩ resistor. |+| 31 | AGND | power_in | Analog ground reference. |+| 32 | AVDD | power_in | Analog-supply voltage input (2.7V to 3.6V); connect a 1-µF capacitor to AGND. |++## Key specifications++| Parameter | Value |+|---|---|+| Manufacturer | Texas Instruments |+| Package | TQFP-32(5x5) |+| Category | Data Acquisition |+| Pins | 32 |++## CAD (KiCad official)++- Symbol: `ADS127L01IPBS`+- Footprint: `Package_QFP:TQFP-32_5x5mm_P0.5mm`+- 3D model: TQFP-32(5x5), generated from the KiCad footprint (body from the F.Fab outline, terminals on the pads, 1.1 mm nominal TQFP height). Neither the vendor nor KiCad ships a 3D model for this package, so the dimensions are nominal, not the manufacturer's CAD (STEP)+- 3D model files: `ads127l01ipbs-etched.step` / `ads127l01ipbs-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `ads127l01ipbs.step` / `ads127l01ipbs.glb` are the bare package body.++## Provenance++Data extracted from the manufacturer datasheet, not a distributor listing:++- **Datasheet:** [Texas Instruments datasheet](https://www.ti.com/cn/lit/gpn/ads127l01) (90 pp, sha256 `7af2117fe188e693`, retrieved 2026-10-01, tier: lcsc)+- **Datasheet language:** Chinese. Pin names, descriptions, and specs on this page were extracted and translated to English by ds2sf; the linked PDF is the manufacturer original.+- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.3`, primary `claude-haiku-4-5-20251001` (text), consensus `claude-sonnet-5-5` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.+- **CAD:** KiCad official libraries (CC-BY-SA 4.0).++[Datasheet PDF](docs/ads127l01ipbs-datasheet.pdf)
page.jsonadded+302
@@ -0,0 +1,302 @@+{+  "slug": "ads127l01ipbs",+  "version": "0.1.0",+  "type": "component",+  "description": "Texas Instruments Analog To Digital Converters (ADC), TQFP-32(5x5). Pinout cross-checked by two models against the datasheet, KiCad symbol/footprint/3D.",+  "tags": [+    "component",+    "data acquisition",+    "ads127l01ipbs",+    "factory-2.0.0",+    "extractor-text"+  ],+  "dependencies": {},+  "hero": {+    "type": "image",+    "path": "docs/hero.png"+  },+  "files": [+    "page.json",+    "README.md",+    "ads127l01ipbs.kicad_sym",+    "ads127l01ipbs.kicad_mod",+    "ads127l01ipbs.glb",+    "ads127l01ipbs.step",+    "ads127l01ipbs.lbr",+    "docs/hero.png",+    "docs/ads127l01ipbs-datasheet.pdf",+    "viewers/symbol.html",+    "viewers/footprint.html"+  ],+  "component": {+    "mpn": "ADS127L01IPBS",+    "manufacturer": "Texas Instruments",+    "package": "TQFP-32(5x5)",+    "pin_count": 32,+    "category": "Data Acquisition",+    "subcategory": "Analog To Digital Converters (ADC)",+    "datasheet": "https://www.ti.com/cn/lit/gpn/ads127l01",+    "parts": {+      "symbol": "ads127l01ipbs.kicad_sym",+      "footprint": "ads127l01ipbs.kicad_mod",+      "model_3d": "ads127l01ipbs-etched.glb",+      "model_3d_plain": "ads127l01ipbs.glb",+      "model_3d_step": "ads127l01ipbs-etched.step",+      "model_3d_step_plain": "ads127l01ipbs.step",+      "lbr": "ads127l01ipbs.lbr"+    },+    "distributor_links": {+      "lcsc": "C1542823",+      "digikey": "296-48867-ND",+      "mouser": "595-ADS127L01IPBS"+    },+    "distributor_check": {+      "checked_at": "2026-10-01T18:39:17Z",+      "source": "Component Ocean /api/assign-pns",+      "digikey": {+        "pn": "296-48867-ND",+        "status": "found",+        "lifecycle": "Active"+      },+      "mouser": {+        "pn": "595-ADS127L01IPBS",+        "status": "found"+      }+    },+    "pins": [+      {+        "number": "1",+        "name": "LVDD",+        "type": "power_out",+        "description": "1.8-V analog supply from internal LDO regulator (INTLDO=0) or input (INTLDO=1); decouple with 1-µF capacitor to AGND."+      },+      {+        "number": "2",+        "name": "CAP1",+        "type": "output",+        "description": "Modulator common-mode voltage output; connect a 1-µF capacitor to AGND."+      },+      {+        "number": "3",+        "name": "AINN",+        "type": "input",+        "description": "Negative differential analog input for ADC measurement (range AGND-0.3V to AVDD+0.3V)."+      },+      {+        "number": "4",+        "name": "AINP",+        "type": "input",+        "description": "Positive differential analog input for ADC measurement (range AGND-0.3V to AVDD+0.3V)."+      },+      {+        "number": "5",+        "name": "AGND",+        "type": "power_in",+        "description": "Analog ground reference."+      },+      {+        "number": "6",+        "name": "AVDD",+        "type": "power_in",+        "description": "Analog-supply voltage input (2.7V to 3.6V); connect a 1-µF capacitor to AGND."+      },+      {+        "number": "7",+        "name": "REXT",+        "type": "input",+        "description": "Analog power-scaling bias resistor pin; connect 60.4-kΩ resistor (HR/LP modes) or 120-kΩ (VLP mode) to AGND."+      },+      {+        "number": "8",+        "name": "INTLDO",+        "type": "input",+        "description": "LVDD voltage selection pin; pull high to AVDD (external 1.8-V supply) or low to AGND (internal LDO) through 10-kΩ resistor."+      },+      {+        "number": "9",+        "name": "REFP",+        "type": "input",+        "description": "Positive analog reference input; connect minimum 10-µF capacitor between REFP and REFN."+      },+      {+        "number": "10",+        "name": "REFN",+        "type": "input",+        "description": "Negative analog reference input."+      },+      {+        "number": "11",+        "name": "CAP2",+        "type": "output",+        "description": "Reference common-mode voltage output; connect a 1-µF capacitor to AGND."+      },+      {+        "number": "12",+        "name": "FILTER1",+        "type": "input",+        "description": "Digital filter select pin bit 1; pull high to DVDD or low to DGND through 100-kΩ resistor."+      },+      {+        "number": "13",+        "name": "FILTER0",+        "type": "input",+        "description": "Digital filter select pin bit 0; pull high/low through 100-kΩ resistor; 00=WB1, 01=WB2, 10=LL, 11=Reserved."+      },+      {+        "number": "14",+        "name": "FSMODE",+        "type": "input",+        "description": "Frame-sync mode select pin; pull high (master mode) or low (slave mode) through 100-kΩ resistor; applies to Frame-Sync interface only."+      },+      {+        "number": "15",+        "name": "OSR1",+        "type": "input",+        "description": "Oversampling ratio select pin bit 1 for decimation filters; pull high/low through 100-kΩ resistor."+      },+      {+        "number": "16",+        "name": "OSR0",+        "type": "input",+        "description": "Oversampling ratio select pin bit 0; pull high/low through 100-kΩ resistor; wideband filters 00=32x, 01=64x, 10=128x, 11=256x."+      },+      {+        "number": "17",+        "name": "START",+        "type": "input",+        "description": "Synchronization signal (active high) to start or restart ADC conversion."+      },+      {+        "number": "18",+        "name": "DAISYIN",+        "type": "input",+        "description": "Daisy-chain input for cascaded device configurations; tie directly to DGND if not daisy-chaining."+      },+      {+        "number": "19",+        "name": "DRDY/FSYNC",+        "type": "bidirectional",+        "description": "SPI interface: data ready output (active low); Frame-sync interface: frame-sync input signal for synchronization."+      },+      {+        "number": "20",+        "name": "DOUT",+        "type": "output",+        "description": "Serial data output from ADC (24-bit or 32-bit format); high-impedance when CS=1 in cascaded SPI configurations."+      },+      {+        "number": "21",+        "name": "DIN",+        "type": "input",+        "description": "Serial data input for SPI interface; tie directly to DGND when using frame-sync interface mode."+      },+      {+        "number": "22",+        "name": "SCLK",+        "type": "bidirectional",+        "description": "Serial clock input for SPI interface (0 to DVDD+0.3V); functions as input/output depending on interface configuration."+      },+      {+        "number": "23",+        "name": "CS",+        "type": "input",+        "description": "Chip select input (active high in SPI cascaded configurations); tie directly to DGND when using frame-sync interface; controls DOUT tri-state."+      },+      {+        "number": "24",+        "name": "CLK",+        "type": "input",+        "description": "Master clock input for internal timing and ADC modulator operation."+      },+      {+        "number": "25",+        "name": "CAP3",+        "type": "output",+        "description": "Internally-generated digital operating voltage output; connect a 1-µF capacitor to DGND."+      },+      {+        "number": "26",+        "name": "DGND",+        "type": "power_in",+        "description": "Digital ground reference."+      },+      {+        "number": "27",+        "name": "DVDD",+        "type": "power_in",+        "description": "Digital-supply voltage input (1.7V to 3.6V); connect a 1-µF capacitor to DGND."+      },+      {+        "number": "28",+        "name": "RESET/PWDN",+        "type": "input",+        "description": "Reset or power-down pin (active low); asynchronous reset of all registers when pulled low."+      },+      {+        "number": "29",+        "name": "HR",+        "type": "input",+        "description": "ADC operating mode select; pull high to DVDD (high-resolution mode) or low to DGND (LP/VLP mode) through 100-kΩ resistor."+      },+      {+        "number": "30",+        "name": "FORMAT",+        "type": "input",+        "description": "Interface protocol select; pull high to DVDD (Frame-Sync mode) or low to DGND (SPI mode) through 100-kΩ resistor."+      },+      {+        "number": "31",+        "name": "AGND",+        "type": "power_in",+        "description": "Analog ground reference."+      },+      {+        "number": "32",+        "name": "AVDD",+        "type": "power_in",+        "description": "Analog-supply voltage input (2.7V to 3.6V); connect a 1-µF capacitor to AGND."+      }+    ],+    "provenance": {+      "extractor": "extract_pins 0.3",+      "factory_chain": {+        "factory": "2.0.0",+        "extractor": "extract_pins 0.3",+        "primary_model": "claude-haiku-4-5-20251001",+        "primary_mode": "text",+        "consensus_model": "claude-sonnet-5-5",+        "consensus": "agreed",+        "guards": "pin_guards 0.1: passed",+        "guard_notes": [+          "extractor flagged: Pin 1 (LVDD) can function as power_out (internal LDO supply when INTLDO=0) or power_in (external 1.8; Pin 19 (DRDY/FSYNC) is bidirectional with mode-dependent function: operates as data ready output (ac; Pin 22 (SCLK) is bidirectional with primary serial clock input function for SPI interface but can op"+        ],+        "pages_sent": 12,+        "cost_usd": 0.4568,+        "at": "2026-10-01T18:39:08"+      },+      "datasheet": {+        "url": "https://www.ti.com/cn/lit/gpn/ads127l01",+        "pages": 90,+        "sha256": "7af2117fe188e693",+        "source_tier": "lcsc"+      },+      "cad": "KiCad official (CC-BY-SA 4.0)",+      "pins": {+        "total": 32,+        "described": 32,+        "cites_pages": true,+        "refuses_to_fabricate": true+      }+    },+    "viewers": {+      "symbol": "viewers/symbol.html",+      "footprint": "viewers/footprint.html"+    }+  },+  "visibility": "public",+  "org": "adom",+  "author": {+    "name": "Ray",+    "email": "[email protected]"+  }+}\ No newline at end of file