component
ADS124S06IRHBR
Public Made by Adomby adom
Texas Instruments Analog To Digital Converters (ADC), VQFN-32-EP(5x5). Pinout cross-checked by two models against the datasheet, KiCad symbol/footprint/3D.
3D Model
Open in new tab ↗
Loads on click. Unloads only if this page sits in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads on click. Unloads only if this page sits in the background.
PCB Footprint
Open full view ↗Loads on click. Unloads only if this page sits in the background.
Datasheet
Open in new tab ↗Loads on click. Unloads only if this page sits in the background.
README
markdownADS124S06IRHBR
Texas Instruments · Analog To Digital Converters (ADC) · VQFN-32-EP(5x5)
ADS124S06IRHBR from Texas Instruments, in a VQFN-32-EP(5x5). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | AINCOM | input | Analog input common for single-ended measurements |
| 2 | AIN5 | input | Analog input 5 |
| 3 | AIN4 | input | Analog input 4 |
| 4 | AIN3 | input | Analog input 3 |
| 5 | AIN2 | input | Analog input 2 |
| 6 | AIN1 | input | Analog input 1 |
| 7 | AIN0 | input | Analog input 0 |
| 8 | START/SYNC | input | Starts conversion or synchronizes conversions; rising edge initiates new conversion |
| 9 | CS | input | Chip select active low; must remain low during entire data transaction |
| 10 | DIN | input | Serial data input; data latched on SCLK falling edge |
| 11 | SCLK | input | Serial clock input; input data latched on falling edge and output data updated on rising edge |
| 12 | DOUT/DRDY | tri_state | Serial data output combined with data ready indication; goes to high-impedance state when CS is high |
| 13 | DRDY | output | Data ready output; transitions low when conversion data are ready |
| 14 | DGND | power_in | Digital ground |
| 15 | IOVDD | power_in | Digital I/O power supply; connect 100-nF or larger capacitor to DGND if not tied to DVDD |
| 16 | DVDD | power_in | Digital core power supply; connect 100-nF or larger capacitor to DGND |
| 17 | CLK | input | External clock input; connect to DGND to use internal 4.096-MHz oscillator |
| 18 | RESET | input | Reset input active low |
| 19 | GPIO3/AIN11 | bidirectional | General-purpose I/O or analog input 11 (ADS124S08 only); logic levels based on analog supply |
| 20 | GPIO2/AIN10 | bidirectional | General-purpose I/O or analog input 10 (ADS124S08 only); logic levels based on analog supply |
| 21 | GPIO1/AIN9 | bidirectional | General-purpose I/O or analog input 9 (ADS124S08 only); logic levels based on analog supply |
| 22 | GPIO0/AIN8 | bidirectional | General-purpose I/O or analog input 8 (ADS124S08 only); logic levels based on analog supply |
| 23 | REFOUT | output | Positive voltage reference output; connect 1-µF to 47-µF capacitor to REFCOM if internal voltage reference enabled |
| 24 | REFCOM | power_in | Negative voltage reference output; connect to AVSS |
| 25 | NC | unconnected | Leave unconnected or connect to AVSS |
| 26 | AVDD | power_in | Positive analog power supply; connect 330-nF or larger capacitor to AVSS |
| 27 | AVSS | power_in | Negative analog power supply |
| 28 | AVSS-SW | power_in | Negative analog power supply low-side switch; connect to AVSS |
| 29 | REFN0 | input | Negative external reference input 0 |
| 30 | REFP0 | input | Positive external reference input 0 |
| 31 | REFN1/AIN7 | input | Negative external reference input 1 or analog input 7 (ADS124S08 only) |
| 32 | REFP1/AIN6 | input | Positive external reference input 1 or analog input 6 (ADS124S08 only) |
| 33 | EP | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Texas Instruments |
| Package | VQFN-32-EP(5x5) |
| Category | Data Acquisition |
| Pins | 33 |
CAD (KiCad official)
- Symbol:
ADS124S06IRHBR - Footprint:
Package_DFN_QFN:QFN-32-1EP_5x5mm_P0.5mm_EP3.3x3.3mm - 3D model: VQFN-32-EP(5x5) (KiCad packages3D, STEP)
- 3D model files:
ads124s06irhbr-etched.step/ads124s06irhbr-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);ads124s06irhbr.step/ads124s06irhbr.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Texas Instruments datasheet (115 pp, sha256
62eb7595c22ca2ef, retrieved 2026-09-24, tier: lcsc) - Datasheet language: Chinese. Pin names, descriptions, and specs on this page were extracted and translated to English by ds2sf; the linked PDF is the manufacturer original.
- Extractor: parts-factory
2.0.0/extract_pins 0.2, primaryclaude-haiku-4-5-20251001(text), consensusclaude-sonnet-4-6(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).