← Commit history
docs/prototype-assembly-plan.mdadded+32
@@ -0,0 +1,32 @@+# Board32 prototype assembly planning++This is a design review document, not a machine program or authorization to fabricate. Physical prototype assembly and probing-workcell simulation are later phases. Keep the firmware output locked until the separate qualification procedure is satisfied.++## Revision and fabrication inputs++Use `aiflow/run/board-32.kicad_pcb`, SHA256 `ea37ce6db20bae331bf41b6638fe9149a17c484e01bc2a0d7fd34917203b7fc3`. The archived board in `kicad/` is not this revision. The export review is in `manufacturing-review/board32/` and the external hardware list is `design/mechanical-bom.csv`.++Two layers, nominal 1 oz surface copper through 3rdPartyFab. 2 oz is available on request but requires a revised stack and design review. Confirm finished barrel copper, hole/slot tolerances, surface finish and the physical stack with the process owner before manufacturing. The four USB shield slots match native exports: two 0.6 × 1.7 mm and two 0.6 × 1.4 mm; these are design dimensions, not finished tolerance guarantees.++## Proposed sequence and inspection points++1. Complete CAM and process review. Separate copper, mask, paste, silkscreen and outline files from documentation layers. Verify board origin and orientation with the assembler, including an asymmetric connector; the position CSV is not a ready-to-run machine program.+2. Establish the exact solder material, deposition method and reflow profile. No jetting shot counts or oven temperatures are prescribed by this design report. Review exposed-pad joints and thermal-via wicking with the selected process.+3. Assemble and inspect the PCB while cooling hardware is absent. Preserve connector access, component polarity, and the 13 bare test contacts. Check hidden joints using the selected assembly inspection method.+4. Plan Q1 installation with the below-tab fastener accessible before final soldering. Do not solder a mechanically strained lead set and then pull the tab into contact. Review whether temporary positioning hardware must be removed before any heating operation.+5. Prepare and inspect the separately machined sink. Three carrier bores and the proposed Q1 blind tap require dimensional/DFM acceptance. The proposed drill point extends into a fin root; stock extrusion is not a finished bolt-on part. Remove burrs and debris before introducing the PCB.+6. Establish independent sink support and the actual case-to-sink separation. Use the spacer-selection worksheet only after collecting real dimensions. Check isolator alignment, surface condition and controlled bond lines. Do not use grease to fill a structural gap.+7. Fit inaccessible carrier nuts and fan mounting screws in the order identified by the clearance study before blocking access with the sink. Current carrier topology, PCB edge retention and fastener preload remain unreleased; nominal collision clearance does not qualify load support.+8. Route the three fan leads and sensor harness with strain relief, clearance from rotor/guard and verified pin identity. Do not infer tach wiring from wire color alone. Keep the fan's actual feedback independent of commanded speed.+9. Verify cold electrical isolation and continuity using a defined procedure before applying power. The exposed MOSFET tab is electrically live; grease is not the qualified isolation barrier. Inspection must address possible screw, edge and sensor paths around the AlN.+10. Transfer the exact as-built identity, material lots and assembly measurements into the later bench qualification record. Current accuracy, fault shutdown, sensor lag, fan tach behavior, contact integrity and installed thermal performance remain physical tests; no result is claimed here.++## Remaining release inputs++- Controlled carrier material, joints, retention and structural load path.+- Supplier dimensions and properties for the isolator and thermal compound.+- Spacer thickness/flatness/parallelism and interface pressure specification.+- Machining, screw length/thread engagement, preload and creep acceptance.+- Assembler-specific orientation, solder deposition, reflow and inspection process.++Do not remove these open items simply because the electrical simulation and native export checks pass.
manufacturing-review/board32/README.md+3−1
@@ -6,6 +6,8 @@ Two copper layers, nominal1oz (35um) surface copper;2oz is available on request  The board outline centerline is68x76mm. Gerber job dimensions68.05x76.05mm include the50um outline stroke. The position CSV uses KiCad absolute coordinates inmm, with Y negated. It contains91 fitted footprints; test contacts intentionally excluded from placement are not pick-and-place parts. BOM includes the full104-reference electrical design and is a dated sourcing snapshot, not a current quote. -Validation:333plated drill hits including4slots,3non-plated holes, and all91placement coordinates/rotations match the saved board. Slot lengths and independent CAM geometry still require review. Layer exports include auxiliary documentation layers; use the named copper/mask/silkscreen/paste/outline subset for a fabrication CAM review. Never treat Fab/Courtyard/User layers as manufacturing artwork.+Validation:333plated drill hits including4slots,3non-plated holes, and all91placement coordinates/rotations match the saved board. A separate [slot review](slot-review.json) confirms all four slot lengths, widths and endpoint orientations against Board32. Independent full CAM/DFM review remains open. Layer exports include auxiliary documentation layers; use the named copper/mask/silkscreen/paste/outline subset for a fabrication CAM review. Never treat Fab/Courtyard/User layers as manufacturing artwork.  The electronic load remains output locked and unflashed. Installed cooling, contact preload, sensor calibration/lag and fault behavior require later bench qualification. The probing simulator is later scope. No purchase or manufacture is authorized by this export.++[Prototype assembly planning](../../docs/prototype-assembly-plan.md) records sequence, access dependencies and unreleased process inputs.
manufacturing-review/board32/slot-review.jsonadded+132
@@ -0,0 +1,132 @@+{+  "status": "pass-slot-geometry-review",+  "boardSha256": "ea37ce6db20bae331bf41b6638fe9149a17c484e01bc2a0d7fd34917203b7fc3",+  "drillSha256": "3778d81377adac39655c66298967dbfd7dbc8fb808e81069c3230049bde9fccd",+  "slotCount": 4,+  "comparisonResolutionMm": 0.001,+  "expected": [+    {+      "reference": "J8",+      "pad": "SH",+      "endpointsMm": [+        [+          156.35000000000002,+          -47.32+        ],+        [+          155.25,+          -47.32+        ]+      ],+      "widthMm": 0.6,+      "overallLengthMm": 1.7+    },+    {+      "reference": "J8",+      "pad": "SH",+      "endpointsMm": [+        [+          160.38,+          -47.32+        ],+        [+          159.57999999999998,+          -47.32+        ]+      ],+      "widthMm": 0.6,+      "overallLengthMm": 1.4+    },+    {+      "reference": "J8",+      "pad": "SH",+      "endpointsMm": [+        [+          156.35000000000002,+          -38.68+        ],+        [+          155.25,+          -38.68+        ]+      ],+      "widthMm": 0.6,+      "overallLengthMm": 1.7+    },+    {+      "reference": "J8",+      "pad": "SH",+      "endpointsMm": [+        [+          160.38,+          -38.68+        ],+        [+          159.57999999999998,+          -38.68+        ]+      ],+      "widthMm": 0.6,+      "overallLengthMm": 1.4+    }+  ],+  "exported": [+    {+      "endpointsMm": [+        [+          155.25,+          -38.68+        ],+        [+          156.35,+          -38.68+        ]+      ],+      "widthMm": 0.6,+      "overallLengthMm": 1.6999999999999944+    },+    {+      "endpointsMm": [+        [+          155.25,+          -47.32+        ],+        [+          156.35,+          -47.32+        ]+      ],+      "widthMm": 0.6,+      "overallLengthMm": 1.6999999999999944+    },+    {+      "endpointsMm": [+        [+          159.58,+          -38.68+        ],+        [+          160.38,+          -38.68+        ]+      ],+      "widthMm": 0.6,+      "overallLengthMm": 1.399999999999983+    },+    {+      "endpointsMm": [+        [+          159.58,+          -47.32+        ],+        [+          160.38,+          -47.32+        ]+      ],+      "widthMm": 0.6,+      "overallLengthMm": 1.399999999999983+    }+  ],+  "limits": "Checks source-to-export slot geometry only; finished plated slot tolerances and fabrication capability are not qualified."+}
tools/review_board32_slots.pyadded+34
@@ -0,0 +1,34 @@+"""Check Board32 native Excellon slot extents and orientation against pad geometry."""+from pathlib import Path+from collections import Counter+import hashlib,json,math,re+import sexp+R=Path(__file__).resolve().parents[1];board=R/'aiflow/run/board-32.kicad_pcb';drill=R/'manufacturing-review/board32/drill/board-32-PTH.drl'+b=sexp.parse(board.read_text());expected=[]+def key(ends,width):return tuple(sorted(tuple(round(v,3)for v in p) for p in ends))+(round(width,3),)+for f in sexp.find(b,'footprint'):+ a=sexp.first(f,'at');x,y=map(float,a[1:3]);theta=math.radians(float(a[3])if len(a)>3 else 0)+ ref=next(p[2] for p in sexp.find(f,'property')if p[1]=='Reference')+ for p in sexp.find(f,'pad'):+  d=sexp.first(p,'drill')+  if not d or 'oval' not in d:continue+  assert p[2]=='thru_hole' and len(d)==4,'Unsupported slot format'+  at=sexp.first(p,'at');u,v=map(float,at[1:3]);angle=math.radians(float(at[3])if len(at)>3 else 0)+  w,h=map(float,d[2:4]);cx=x+u*math.cos(theta)+v*math.sin(theta);cy=-y+u*math.sin(theta)-v*math.cos(theta)+  # Pad orientation in saved board is absolute; export frame reverses board Y.+  longangle=angle+(math.pi/2 if h>w else 0);travel=abs(h-w);dx=travel/2*math.cos(longangle);dy=travel/2*math.sin(longangle)+  ends=[[cx-dx,cy-dy],[cx+dx,cy+dy]]+  expected.append({'reference':ref,'pad':p[1],'endpointsMm':ends,'widthMm':min(w,h),'overallLengthMm':max(w,h),'key':key(ends,min(w,h))})+actual=[];tools={};tool=None+for line in drill.read_text().splitlines():+ m=re.fullmatch(r'T(\d+)C([\d.]+)',line)+ if m:tools[m[1]]=float(m[2]);continue+ m=re.fullmatch(r'T(\d+)',line)+ if m:tool=m[1];continue+ if 'G85' in line:+  ends=[list(map(float,c)) for c in re.findall(r'X(-?[\d.]+)Y(-?[\d.]+)',line)];assert len(ends)==2+  width=tools[tool];actual.append({'endpointsMm':ends,'widthMm':width,'overallLengthMm':math.dist(*ends)+width,'key':key(ends,width)})+assert Counter(x['key']for x in expected)==Counter(x['key']for x in actual),'Slot endpoint/width mismatch'+for x in expected+actual:x.pop('key')+out={'status':'pass-slot-geometry-review','boardSha256':hashlib.sha256(board.read_bytes()).hexdigest(),'drillSha256':hashlib.sha256(drill.read_bytes()).hexdigest(),'slotCount':len(actual),'comparisonResolutionMm':.001,'expected':expected,'exported':actual,'limits':'Checks source-to-export slot geometry only; finished plated slot tolerances and fabrication capability are not qualified.'}+(R/'manufacturing-review/board32/slot-review.json').write_text(json.dumps(out,indent=2)+'\n');print(json.dumps({'status':out['status'],'slots':len(actual),'widthsMm':[x['widthMm']for x in actual],'lengthsMm':[round(x['overallLengthMm'],3)for x in actual]}))
videos/final-stage-candidates.json+2−1
@@ -12,7 +12,8 @@       "file": "mechanical/board32-selected-cooling/selected-cooling-review.mp4",       "narration": "The model includes the fan wiring, guard and revised thermal interface. This fan animation is simulated; the amber box marks the cooler clearance.",       "speed": 1,-      "timingWarning": "Native recorder timestamp repair failed; qualitative review only."+      "timingWarning": "Native recorder timestamp repair failed; qualitative review only.",+      "publicFilmStatus": "Hold: includes carrier/scaffold geometry excluded by existing public edit plan. Internal review only pending a public-safe shot."     }   ] }