main
Ray
Publish 0.1.0
23c3ddd
ADM6710LARJZ-REEL7
Analog Devices · Monitors & Reset Circuits · SOT-23-6
ADM6710LARJZ-REEL7 from Analog Devices, in a SOT-23-6. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model). Symbol and footprint from KiCad-official CAD; the 3D model is generated from the datasheet's package dimensions.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | IN1 | input | Input Voltage 1 is an adjustable monitored input (0.62 V internal threshold, set with an external resistor divider) and must not be left floating or grounded when unused. |
| 2 | IN2 | power_in | Input Voltage 2 is the power supply input for the ADM6710 and also a monitored input, with the RESET output guaranteed correct down to IN2 = 1 V. |
| 3 | IN3 | input | Input Voltage 3 is a monitored supply input that must not be left floating or grounded and should be tied to a supply above its threshold when unused. |
| 4 | IN4 | input | Input Voltage 4 is a monitored supply input (adjustable on this variant per the ordering guide) and must not be left floating or grounded when unused. |
| 5 | GND | power_in | Ground reference for the device. |
| 6 | RESET | output | Active low, open-drain reset output that goes low when any monitored input falls below its threshold and stays low for 200 ms typical after all inputs recover, with a weak internal pull-up of about 10 µA to IN2 and a 20 mA absolute maximum continuous current. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Analog Devices |
| Package | SOT-23-6 |
| Category | Power Supply Chip |
| Pins | 6 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| VIN2 operating voltage (ADM6710, not Q), TA = −40°C to +125°C | VIN2 | 1.2 | 5.5 | V | All devices except ADM6710Q; TA = −40°C to +125°C | 3 | |
| VIN2 operating voltage (ADM6710, not Q), TA = 0°C to +125°C | VIN2 | 1 | 5.5 | V | All devices except ADM6710Q; TA = 0°C to +125°C | 3 | |
| INx input current (1.8 V supply input, IN3 on this part) | 25 | 40 | µA | INX = nominal input voltage (for 1.8 V, 2.5 V and 5.0 V supplies) | 3 | ||
| IN2 input current (3.3 V supply) | 55 | 115 | µA | IN2 = nominal input voltage (for 3.0 V and 3.3 V supplies); the supply splits into 25 µA for the resistor divider and 30 µA for other circuits | 3 | ||
| Input current, adjustable input IN1 | 0.4 | µA | VIN1 = 0 V to 0.85 V (for adjustable thresholds) | 3 | |||
| Input current, adjustable input IN4 | VIN3, VIN4 | 0.2 | µA | VIN3, VIN4 = 0 V to 0.85 V (for adjustable thresholds) | 3 | ||
| Threshold voltage, 3.3 V monitor (−5%) | VTH | 3 | 3.08 | 3.15 | V | INX decreasing; 3.3 V (−5%) | 3 |
| Threshold voltage, 1.8 V monitor (−5%) | VTH | 1.62 | 1.67 | 1.71 | V | INX decreasing; 1.8 V (−5%) | 3 |
| Adjustable threshold voltage | VTH | 0.611 | 0.62 | 0.629 | V | INX decreasing | 3 |
| RESET timeout period | tRP | 140 | 200 | 280 | ms | 3 | |
| RESET threshold hysteresis | VHYST | 0.3 | %VTH | INX increasing relative to INX decreasing | 3 | ||
| RESET threshold temperature coefficient | TCVTH | 60 | ppm/°C | 3 | |||
| INx to RESET delay | tRP | 30 | µs | VIN falling at 10 mV/µs from VTH to VTH − 50 mV | 3 | ||
| RESET output low voltage (VIN2 = 5 V) | VOL | 0.3 | V | VIN2, VCC = 5 V, ISINK = 2 mA | 3 | ||
| RESET output low voltage (VIN2 = 2.5 V) | VOL | 0.4 | V | VIN2, VCC = 2.5 V, ISINK = 1.2 mA | 3 | ||
| RESET output low voltage (VIN2 = 1.0 V) | VOL | 0.3 | V | VIN2 = 1.0 , ISINK = 20 µA, TA = 0°C to +125°C | 3 | ||
| RESET output high source current | IOH | 10 | µA | VIN2 ≥ 2.0 V, RESET deasserted | 3 | ||
| VCC, INX, RESET to GND voltage | -0.3 | 6 | V | to GND | 4 | ||
| Continuous RESET current | 20 | mA | 4 | ||||
| Storage temperature range | -65 | 150 | °C | 4 | |||
| Operating temperature range | -40 | 125 | °C | 4 | |||
| Lead temperature | 300 | °C | 10 sec | 4 | |||
| Junction temperature | 135 | °C | 4 | ||||
| Thermal resistance, junction to ambient, 6-lead SOT-23 | θJA | 169.5 | °C/W | 6-lead SOT-23 | 4 |
CAD (land: KiCad; 3D: generated from the datasheet)
- Symbol:
ADM6710LARJZ-REEL7 - Footprint:
Package_TO_SOT_SMD:SOT-23-6 - 3D model: SOT-23-6, generated on the KiCad land (body 1.6 x 2.9 mm, terminals on the pads, 1.2 mm tall, datasheet A, midpoint of min and max). KiCad's stock model for this land is taller than the datasheet allows, so the model is generated from the datasheet drawing; the dimensions come from the datasheet drawing where it was read and are defaults otherwise (see provenance.model_3d_generated), not the manufacturer's CAD (STEP)
- 3D model files:
adm6710larjz-etched.step/adm6710larjz-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);adm6710larjz.step/adm6710larjz.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Analog Devices datasheet (12 pp, sha256
17db66dd289904e0, retrieved 2026-11-13, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: land: KiCad official libraries (CC-BY-SA 4.0); 3D: generated from the datasheet's package dimensions (provenance.model_3d_generated).
# ADM6710LARJZ-REEL7
**Analog Devices** · Monitors & Reset Circuits · SOT-23-6
ADM6710LARJZ-REEL7 from Analog Devices, in a SOT-23-6. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model). Symbol and footprint from KiCad-official CAD; the 3D model is generated from the datasheet's package dimensions.
## Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | IN1 | input | Input Voltage 1 is an adjustable monitored input (0.62 V internal threshold, set with an external resistor divider) and must not be left floating or grounded when unused. |
| 2 | IN2 | power_in | Input Voltage 2 is the power supply input for the ADM6710 and also a monitored input, with the RESET output guaranteed correct down to IN2 = 1 V. |
| 3 | IN3 | input | Input Voltage 3 is a monitored supply input that must not be left floating or grounded and should be tied to a supply above its threshold when unused. |
| 4 | IN4 | input | Input Voltage 4 is a monitored supply input (adjustable on this variant per the ordering guide) and must not be left floating or grounded when unused. |
| 5 | GND | power_in | Ground reference for the device. |
| 6 | RESET | output | Active low, open-drain reset output that goes low when any monitored input falls below its threshold and stays low for 200 ms typical after all inputs recover, with a weak internal pull-up of about 10 µA to IN2 and a 20 mA absolute maximum continuous current. |
## Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Analog Devices |
| Package | SOT-23-6 |
| Category | Power Supply Chip |
| Pins | 6 |
## Electrical characteristics
Limits as printed in the datasheet (page.json `metadata.characteristics` carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| VIN2 operating voltage (ADM6710, not Q), TA = −40°C to +125°C | VIN2 | 1.2 | | 5.5 | V | All devices except ADM6710Q; TA = −40°C to +125°C | 3 |
| VIN2 operating voltage (ADM6710, not Q), TA = 0°C to +125°C | VIN2 | 1 | | 5.5 | V | All devices except ADM6710Q; TA = 0°C to +125°C | 3 |
| INx input current (1.8 V supply input, IN3 on this part) | | | 25 | 40 | µA | INX = nominal input voltage (for 1.8 V, 2.5 V and 5.0 V supplies) | 3 |
| IN2 input current (3.3 V supply) | | | 55 | 115 | µA | IN2 = nominal input voltage (for 3.0 V and 3.3 V supplies); the supply splits into 25 µA for the resistor divider and 30 µA for other circuits | 3 |
| Input current, adjustable input IN1 | | | | 0.4 | µA | VIN1 = 0 V to 0.85 V (for adjustable thresholds) | 3 |
| Input current, adjustable input IN4 | VIN3, VIN4 | | | 0.2 | µA | VIN3, VIN4 = 0 V to 0.85 V (for adjustable thresholds) | 3 |
| Threshold voltage, 3.3 V monitor (−5%) | VTH | 3 | 3.08 | 3.15 | V | INX decreasing; 3.3 V (−5%) | 3 |
| Threshold voltage, 1.8 V monitor (−5%) | VTH | 1.62 | 1.67 | 1.71 | V | INX decreasing; 1.8 V (−5%) | 3 |
| Adjustable threshold voltage | VTH | 0.611 | 0.62 | 0.629 | V | INX decreasing | 3 |
| RESET timeout period | tRP | 140 | 200 | 280 | ms | | 3 |
| RESET threshold hysteresis | VHYST | | 0.3 | | %VTH | INX increasing relative to INX decreasing | 3 |
| RESET threshold temperature coefficient | TCVTH | | 60 | | ppm/°C | | 3 |
| INx to RESET delay | tRP | | 30 | | µs | VIN falling at 10 mV/µs from VTH to VTH − 50 mV | 3 |
| RESET output low voltage (VIN2 = 5 V) | VOL | | 0.3 | | V | VIN2, VCC = 5 V, ISINK = 2 mA | 3 |
| RESET output low voltage (VIN2 = 2.5 V) | VOL | | 0.4 | | V | VIN2, VCC = 2.5 V, ISINK = 1.2 mA | 3 |
| RESET output low voltage (VIN2 = 1.0 V) | VOL | | 0.3 | | V | VIN2 = 1.0 , ISINK = 20 µA, TA = 0°C to +125°C | 3 |
| RESET output high source current | IOH | | 10 | | µA | VIN2 ≥ 2.0 V, RESET deasserted | 3 |
| VCC, INX, RESET to GND voltage | | -0.3 | | 6 | V | to GND | 4 |
| Continuous RESET current | | | | 20 | mA | | 4 |
| Storage temperature range | | -65 | | 150 | °C | | 4 |
| Operating temperature range | | -40 | | 125 | °C | | 4 |
| Lead temperature | | | | 300 | °C | 10 sec | 4 |
| Junction temperature | | | | 135 | °C | | 4 |
| Thermal resistance, junction to ambient, 6-lead SOT-23 | θJA | | 169.5 | | °C/W | 6-lead SOT-23 | 4 |
## CAD (land: KiCad; 3D: generated from the datasheet)
- Symbol: `ADM6710LARJZ-REEL7`
- Footprint: `Package_TO_SOT_SMD:SOT-23-6`
- 3D model: SOT-23-6, generated on the KiCad land (body 1.6 x 2.9 mm, terminals on the pads, 1.2 mm tall, datasheet A, midpoint of min and max). KiCad's stock model for this land is taller than the datasheet allows, so the model is generated from the datasheet drawing; the dimensions come from the datasheet drawing where it was read and are defaults otherwise (see provenance.model_3d_generated), not the manufacturer's CAD (STEP)
- 3D model files: `adm6710larjz-etched.step` / `adm6710larjz-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `adm6710larjz.step` / `adm6710larjz.glb` are the bare package body.
## Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- **Datasheet:** [Analog Devices datasheet](https://www.analog.com/media/en/technical-documentation/data-sheets/ADM6710.pdf) (12 pp, sha256 `17db66dd289904e0`, retrieved 2026-11-13, tier: manufacturer)
- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.3`, primary `claude-haiku-5-5` (text), consensus `claude-sonnet-5-5` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
- **CAD:** land: KiCad official libraries (CC-BY-SA 4.0); 3D: generated from the datasheet's package dimensions (provenance.model_3d_generated).
[Datasheet PDF](docs/adm6710larjz-datasheet.pdf)