component
ADM1191-2ARMZ-R7
Public Made by Adomby adom
Analog Devices Power Management Specialized - PMIC, MSOP-10. Pinout cross-checked by two models against the datasheet, KiCad symbol/footprint/3D.
main
ADM1191-2ARMZ-R7
Analog Devices · Power Management Specialized - PMIC · MSOP-10
ADM1191-2ARMZ-R7 from Analog Devices, in a MSOP-10. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | VCC | power_in | Positive supply input with an operating range of 3.15 V to 26 V; an undervoltage lockout circuit resets the ADM1191 when a low supply voltage is detected. |
| 2 | SENSE | input | Current sense input; the voltage across the sense resistor between VCC and SENSE is proportional to load current and is amplified before ADC digitization. |
| 3 | CONV | input | Convert start input; a high level enables an ADC conversion, and the pin should be tied high if not required so the ADC runs. |
| 4 | GND | power_in | Chip ground pin. |
| 5 | SETV | input | Overcurrent threshold input compared with the current sense amplifier output, where a lower voltage causes ALERTB to assert at a lower current level, with a typical response time of 1 µs to 2 µs. |
| 6 | SCL | input | I2C clock input that is open-drain and requires an external resistive pull-up. |
| 7 | SDA | bidirectional | I2C data input/output that is open-drain and requires an external resistive pull-up. |
| 8 | A0 | input | I2C address pin that can be tied low, tied high, left floating, or tied low through a resistor, and which sets one of sixteen addresses together with A1. |
| 9 | A1 | input | I2C address pin that can be tied low, tied high, left floating, or tied low through a resistor, and which sets one of sixteen addresses together with A0. |
| 10 | ALERTB | output | Active-low, open-drain overcurrent alert output that asserts low on an overcurrent condition, latches until cleared via the ALERT_EN register, and is rated to 30 V. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Analog Devices |
| Package | MSOP-10 |
| Category | Power Supply Chip |
| Pins | 10 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Operating Voltage Range, VCC | VCC | 3.15 | 26 | V | 3 | ||
| Supply Current | ICC | 1.7 | 2 | mA | 3 | ||
| Input Current, CONV pin | ICONV | -2 | 2 | µA | 3 | ||
| Current Sense Absolute Accuracy | -1.45 | 1.45 | % | 0°C to +70°C; VSENSE = 75 mV | 3 | ||
| Current Sense Absolute Accuracy | -1.8 | 1.8 | % | 0°C to +70°C; VSENSE = 50 mV | 3 | ||
| Current Sense Absolute Accuracy | -2.8 | 2.8 | % | 0°C to +70°C; VSENSE = 25 mV | 3 | ||
| Current Sense Absolute Accuracy | -5.7 | 5.7 | % | 0°C to +70°C; VSENSE = 12.5 mV | 3 | ||
| Current Sense Absolute Accuracy | -1.5 | 1.5 | % | 0°C to +85°C; VSENSE = 75 mV | 3 | ||
| Current Sense Absolute Accuracy | -2.95 | 2.95 | % | 0°C to +85°C; VSENSE = 25 mV | 3 | ||
| Current Sense Absolute Accuracy | -6.1 | 6.1 | % | 0°C to +85°C; VSENSE = 12.5 mV | 3 | ||
| Current Sense Absolute Accuracy | -1.95 | 1.95 | % | −40°C to +85°C; VSENSE = 75 mV | 3 | ||
| Current Sense Absolute Accuracy | -2.45 | 2.45 | % | −40°C to +85°C; VSENSE = 50 mV | 3 | ||
| Voltage Sense Accuracy | -0.85 | 0.85 | % | 0°C to +70°C; VCC = 3.0 V to 5.5 V (low range) | 3 | ||
| Voltage Sense Accuracy | -0.9 | 0.9 | % | 0°C to +70°C; VCC = 10.8 V to 16.5 V (high range) | 3 | ||
| Voltage Sense Accuracy | -1.15 | 1.15 | % | −40°C to +85°C; VCC = 10.8 V to 16.5 V (high range) | 3 | ||
| Input Current, SENSE pin | ISENSE | -1 | 1 | µA | VSENSE = VCC | 3 | |
| Overcurrent Trip Threshold | 98 | 100 | 102 | mV | VSETV = 1.8 V | 3 | |
| Overcurrent Trip Threshold | 49.5 | 50 | 50.5 | mV | VSETV = 0.9 V | 3 | |
| Input Current, SETV leakage | ISETVLEAK | -1 | 1 | µA | VSETV = 0.9 V to 1.9 V | 3 | |
| Output Low Voltage, ALERTB | VALERTOL | 0.05 | 0.1 | V | IALERT = −100 µA | 3 | |
| Output Low Voltage, ALERTB | VALERTOL | 1 | 1.5 | V | IALERT = −2 mA | 3 | |
| Input Current, ALERTB | IALERT | -1 | 1 | µA | VALERT = VCC; ALERTB not asserted | 3 | |
| Low State Voltage, A0/A1 (Set Address to 00) | VADRLOWV | 0 | 0.8 | V | Low state | 4 | |
| Resistor to Ground State, A0/A1 (Set Address to 01) | RADRLOWZ | 80 | 120 | 160 | kΩ | Resistor to ground state, load pin with specified resistance for 01 decode | 4 |
| Open State Input Current, A0/A1 (Set Address to 10) | IADRHIGHZ | -0.3 | 0.3 | µA | Open state, maximum load allowed on the A0 pin or A1 pin for 10 decode | 4 | |
| High State Voltage, A0/A1 (Set Address to 11) | VADRHIGHV | 2 | 5.5 | V | High state | 4 | |
| Input Current for 00 Decode | IADRLOW | -40 | -25 | µA | VADR = 0 V to 0.8 V | 4 | |
| Input Current for 11 Decode | IADRHIGH | 3 | 6 | µA | VADR = 2.0 V to 5.5 V | 4 | |
| Low Level Input Voltage | VIL | 0.3 | V | VBUS = 3.0 V to 5.5 V | 4 | ||
| High Level Input Voltage | VIH | 0.7 | V | VBUS = 3.0 V to 5.5 V | 4 | ||
| Output Fall Time on SDA from VIHMIN to VILMAX | 250 | ns | CBUS = bus capacitance from SDA to GND | 4 | |||
| Maximum Width of Spikes Suppressed by Input Filtering on SDA and SCL | 50 | 250 | ns | 4 | |||
| Input Current on SDA/SCL When Not Driving a Logic Low Output | II | -10 | 10 | µA | 4 | ||
| SDA Output Data Hold Time | tHD;DAT | 100 | 900 | ns | 4 | ||
| VCC Pin Absolute Maximum | VCC | 30 | V | 5 | |||
| SENSE Pin Absolute Maximum | 30 | V | 5 | ||||
| CONV Pin Absolute Maximum | -0.3 | 6 | V | 5 | |||
| SETV Pin Absolute Maximum | 6 | V | 5 | ||||
| ALERTB Pin Absolute Maximum | 30 | V | 5 | ||||
| SDA Pin, SCL Pin Absolute Maximum | -0.3 | 6 | V | 5 | |||
| A0 Pin, A1 Pin Absolute Maximum | -0.3 | 6 | V | 5 | |||
| Storage Temperature Range | -65 | 125 | °C | 5 | |||
| Operating Temperature Range | -40 | 85 | °C | 5 | |||
| Lead Temperature (Soldering) | 300 | °C | 10 sec | 5 | |||
| Junction Temperature | 150 | °C | 5 | ||||
| Thermal Resistance, junction to ambient (θJA), 10-Lead MSOP | θJA | 137.5 | °C/W | Device soldered in circuit board, surface-mount package | 5 | ||
| UVLO Threshold, VCC rising | VUVLO | 2.8 | V | VCC rising | 3 | ||
| Logic Low Threshold, CONV | VCONVL | 1.2 | V | 3 | |||
| Logic High Threshold, CONV | VCONVH | 1.4 | V | 3 | |||
| Low Level Output Voltage on SDA | VOL | 0.4 | V | IOL = 3 mA | 4 | ||
| SCL Clock Frequency | fSCL | 400 | kHz | 4 | |||
| ADC Conversion Time | 150 | µs | 3 | ||||
| Overcurrent Trip Gain, VSETV/(VCC − VSENSE) | VSETV/(VCC − VSENSE) | 18 | VSETV = 0.9 V to 1.9 V | 3 | |||
| UVLO Hysteresis, VUVLOHYST | VUVLOHYST | 80 | mV | 3 |
CAD (KiCad official)
- Symbol:
ADM1191-2ARMZ-R7 - Footprint:
Package_SO:MSOP-10_3x3mm_P0.5mm - 3D model: MSOP-10 (KiCad packages3D, STEP)
- 3D model files:
adm1191-2armz-r7-etched.step/adm1191-2armz-r7-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);adm1191-2armz-r7.step/adm1191-2armz-r7.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Analog Devices datasheet (16 pp, sha256
859a3b662ca04f2e, retrieved 2026-10-28, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).
# ADM1191-2ARMZ-R7
**Analog Devices** · Power Management Specialized - PMIC · MSOP-10
ADM1191-2ARMZ-R7 from Analog Devices, in a MSOP-10. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
## Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | VCC | power_in | Positive supply input with an operating range of 3.15 V to 26 V; an undervoltage lockout circuit resets the ADM1191 when a low supply voltage is detected. |
| 2 | SENSE | input | Current sense input; the voltage across the sense resistor between VCC and SENSE is proportional to load current and is amplified before ADC digitization. |
| 3 | CONV | input | Convert start input; a high level enables an ADC conversion, and the pin should be tied high if not required so the ADC runs. |
| 4 | GND | power_in | Chip ground pin. |
| 5 | SETV | input | Overcurrent threshold input compared with the current sense amplifier output, where a lower voltage causes ALERTB to assert at a lower current level, with a typical response time of 1 µs to 2 µs. |
| 6 | SCL | input | I2C clock input that is open-drain and requires an external resistive pull-up. |
| 7 | SDA | bidirectional | I2C data input/output that is open-drain and requires an external resistive pull-up. |
| 8 | A0 | input | I2C address pin that can be tied low, tied high, left floating, or tied low through a resistor, and which sets one of sixteen addresses together with A1. |
| 9 | A1 | input | I2C address pin that can be tied low, tied high, left floating, or tied low through a resistor, and which sets one of sixteen addresses together with A0. |
| 10 | ALERTB | output | Active-low, open-drain overcurrent alert output that asserts low on an overcurrent condition, latches until cleared via the ALERT_EN register, and is rated to 30 V. |
## Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Analog Devices |
| Package | MSOP-10 |
| Category | Power Supply Chip |
| Pins | 10 |
## Electrical characteristics
Limits as printed in the datasheet (page.json `metadata.characteristics` carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Operating Voltage Range, VCC | VCC | 3.15 | | 26 | V | | 3 |
| Supply Current | ICC | | 1.7 | 2 | mA | | 3 |
| Input Current, CONV pin | ICONV | -2 | | 2 | µA | | 3 |
| Current Sense Absolute Accuracy | | -1.45 | | 1.45 | % | 0°C to +70°C; VSENSE = 75 mV | 3 |
| Current Sense Absolute Accuracy | | -1.8 | | 1.8 | % | 0°C to +70°C; VSENSE = 50 mV | 3 |
| Current Sense Absolute Accuracy | | -2.8 | | 2.8 | % | 0°C to +70°C; VSENSE = 25 mV | 3 |
| Current Sense Absolute Accuracy | | -5.7 | | 5.7 | % | 0°C to +70°C; VSENSE = 12.5 mV | 3 |
| Current Sense Absolute Accuracy | | -1.5 | | 1.5 | % | 0°C to +85°C; VSENSE = 75 mV | 3 |
| Current Sense Absolute Accuracy | | -2.95 | | 2.95 | % | 0°C to +85°C; VSENSE = 25 mV | 3 |
| Current Sense Absolute Accuracy | | -6.1 | | 6.1 | % | 0°C to +85°C; VSENSE = 12.5 mV | 3 |
| Current Sense Absolute Accuracy | | -1.95 | | 1.95 | % | −40°C to +85°C; VSENSE = 75 mV | 3 |
| Current Sense Absolute Accuracy | | -2.45 | | 2.45 | % | −40°C to +85°C; VSENSE = 50 mV | 3 |
| Voltage Sense Accuracy | | -0.85 | | 0.85 | % | 0°C to +70°C; VCC = 3.0 V to 5.5 V (low range) | 3 |
| Voltage Sense Accuracy | | -0.9 | | 0.9 | % | 0°C to +70°C; VCC = 10.8 V to 16.5 V (high range) | 3 |
| Voltage Sense Accuracy | | -1.15 | | 1.15 | % | −40°C to +85°C; VCC = 10.8 V to 16.5 V (high range) | 3 |
| Input Current, SENSE pin | ISENSE | -1 | | 1 | µA | VSENSE = VCC | 3 |
| Overcurrent Trip Threshold | | 98 | 100 | 102 | mV | VSETV = 1.8 V | 3 |
| Overcurrent Trip Threshold | | 49.5 | 50 | 50.5 | mV | VSETV = 0.9 V | 3 |
| Input Current, SETV leakage | ISETVLEAK | -1 | | 1 | µA | VSETV = 0.9 V to 1.9 V | 3 |
| Output Low Voltage, ALERTB | VALERTOL | | 0.05 | 0.1 | V | IALERT = −100 µA | 3 |
| Output Low Voltage, ALERTB | VALERTOL | | 1 | 1.5 | V | IALERT = −2 mA | 3 |
| Input Current, ALERTB | IALERT | -1 | | 1 | µA | VALERT = VCC; ALERTB not asserted | 3 |
| Low State Voltage, A0/A1 (Set Address to 00) | VADRLOWV | 0 | | 0.8 | V | Low state | 4 |
| Resistor to Ground State, A0/A1 (Set Address to 01) | RADRLOWZ | 80 | 120 | 160 | kΩ | Resistor to ground state, load pin with specified resistance for 01 decode | 4 |
| Open State Input Current, A0/A1 (Set Address to 10) | IADRHIGHZ | -0.3 | | 0.3 | µA | Open state, maximum load allowed on the A0 pin or A1 pin for 10 decode | 4 |
| High State Voltage, A0/A1 (Set Address to 11) | VADRHIGHV | 2 | | 5.5 | V | High state | 4 |
| Input Current for 00 Decode | IADRLOW | -40 | | -25 | µA | VADR = 0 V to 0.8 V | 4 |
| Input Current for 11 Decode | IADRHIGH | 3 | | 6 | µA | VADR = 2.0 V to 5.5 V | 4 |
| Low Level Input Voltage | VIL | | | 0.3 | V | VBUS = 3.0 V to 5.5 V | 4 |
| High Level Input Voltage | VIH | 0.7 | | | V | VBUS = 3.0 V to 5.5 V | 4 |
| Output Fall Time on SDA from VIHMIN to VILMAX | | | | 250 | ns | CBUS = bus capacitance from SDA to GND | 4 |
| Maximum Width of Spikes Suppressed by Input Filtering on SDA and SCL | | 50 | | 250 | ns | | 4 |
| Input Current on SDA/SCL When Not Driving a Logic Low Output | II | -10 | | 10 | µA | | 4 |
| SDA Output Data Hold Time | tHD;DAT | 100 | | 900 | ns | | 4 |
| VCC Pin Absolute Maximum | VCC | | | 30 | V | | 5 |
| SENSE Pin Absolute Maximum | | | | 30 | V | | 5 |
| CONV Pin Absolute Maximum | | -0.3 | | 6 | V | | 5 |
| SETV Pin Absolute Maximum | | | | 6 | V | | 5 |
| ALERTB Pin Absolute Maximum | | | | 30 | V | | 5 |
| SDA Pin, SCL Pin Absolute Maximum | | -0.3 | | 6 | V | | 5 |
| A0 Pin, A1 Pin Absolute Maximum | | -0.3 | | 6 | V | | 5 |
| Storage Temperature Range | | -65 | | 125 | °C | | 5 |
| Operating Temperature Range | | -40 | | 85 | °C | | 5 |
| Lead Temperature (Soldering) | | | | 300 | °C | 10 sec | 5 |
| Junction Temperature | | | | 150 | °C | | 5 |
| Thermal Resistance, junction to ambient (θJA), 10-Lead MSOP | θJA | | 137.5 | | °C/W | Device soldered in circuit board, surface-mount package | 5 |
| UVLO Threshold, VCC rising | VUVLO | | 2.8 | | V | VCC rising | 3 |
| Logic Low Threshold, CONV | VCONVL | | 1.2 | | V | | 3 |
| Logic High Threshold, CONV | VCONVH | | 1.4 | | V | | 3 |
| Low Level Output Voltage on SDA | VOL | | 0.4 | | V | IOL = 3 mA | 4 |
| SCL Clock Frequency | fSCL | | 400 | | kHz | | 4 |
| ADC Conversion Time | | | 150 | | µs | | 3 |
| Overcurrent Trip Gain, VSETV/(VCC − VSENSE) | VSETV/(VCC − VSENSE) | | 18 | | | VSETV = 0.9 V to 1.9 V | 3 |
| UVLO Hysteresis, VUVLOHYST | VUVLOHYST | | 80 | | mV | | 3 |
## CAD (KiCad official)
- Symbol: `ADM1191-2ARMZ-R7`
- Footprint: `Package_SO:MSOP-10_3x3mm_P0.5mm`
- 3D model: MSOP-10 (KiCad packages3D, STEP)
- 3D model files: `adm1191-2armz-r7-etched.step` / `adm1191-2armz-r7-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `adm1191-2armz-r7.step` / `adm1191-2armz-r7.glb` are the bare package body.
## Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- **Datasheet:** [Analog Devices datasheet](https://www.analog.com/media/en/technical-documentation/data-sheets/ADM1191.pdf) (16 pp, sha256 `859a3b662ca04f2e`, retrieved 2026-10-28, tier: manufacturer)
- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.3`, primary `claude-haiku-5-5` (text), consensus `claude-sonnet-5-5` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
- **CAD:** KiCad official libraries (CC-BY-SA 4.0).
[Datasheet PDF](docs/adm1191-2armz-r7-datasheet.pdf)