← Commit history
README.md+69−66
@@ -8,26 +8,26 @@ ADC0804LCWMX from Texas Instruments, in a SOIC-20-300mil. Pinout and pin descrip  | Pin | Name | Type | Function | |---|---|---|---|-| 1 | CS | input | Active-low chip select; CS and WR must both be low to start a conversion, and the datasheet assumes CS brackets the WR strobe. |-| 2 | RD | input | Active-low read strobe that, with CS low, resets INTR and enables the tri-state output latches onto DB0 to DB7. |-| 3 | WR | input | Active-low write strobe; the conversion starts on the low-to-high transition of WR while CS is low, and the WR pulse width must be at least 100 ns. |-| 4 | CLK IN | input | Clock input to a Schmitt trigger for an external clock of 100 kHz to 1460 kHz (640 kHz for specified accuracy, 40% to 60% duty cycle), or used with an external RC for self-clocking. |-| 5 | INTR | output | Active-low interrupt request output that goes high-to-low at the end of a conversion and can be tied to WR for free-running operation. |-| 6 | VIN(+) | power_in | Positive differential analog input that must stay within GND - 0.05 V to VCC + 0.05 V, with input currents above 1 mA requiring an external diode. |-| 7 | VIN(-) | power_in | Negative differential analog input used for offset (tare) correction, with the same GND - 0.05 V to VCC + 0.05 V range, and the output code is 00 hex when VIN(-) is at or above VIN(+). |-| 8 | A GND | power_in | Analog ground pin that should be wired to a single point separate from the logic ground and tied to D GND as the datasheet specifies. |-| 9 | VREF/2 | power_in | Reference voltage input for full-scale adjustment with an internal gain of 2, so the full-scale span is twice the voltage on this pin, and it defaults to VCC/2 when unconnected. |-| 10 | D GND | power_in | Digital ground pin for the logic and output drivers, to which the supply bypass capacitor should return. |-| 11 | DB7 | tri_state | Tri-state data output bit 7 (MSB), valid only when CS and RD are both low, with a logic-0 output of 0.4 V max at 1.6 mA. |-| 12 | DB6 | tri_state | Tri-state data output bit 6, valid only when CS and RD are both low, with a logic-0 output of 0.4 V max at 1.6 mA. |-| 13 | DB5 | tri_state | Tri-state data output bit 5, valid only when CS and RD are both low, with a logic-0 output of 0.4 V max at 1.6 mA. |-| 14 | DB4 | tri_state | Tri-state data output bit 4, valid only when CS and RD are both low, with a logic-0 output of 0.4 V max at 1.6 mA. |-| 15 | DB3 | tri_state | Tri-state data output bit 3, valid only when CS and RD are both low, with a logic-0 output of 0.4 V max at 1.6 mA. |-| 16 | DB2 | tri_state | Tri-state data output bit 2, valid only when CS and RD are both low, with a logic-0 output of 0.4 V max at 1.6 mA. |-| 17 | DB1 | tri_state | Tri-state data output bit 1, valid only when CS and RD are both low, with a logic-0 output of 0.4 V max at 1.6 mA. |-| 18 | DB0 (LSB) | tri_state | Tri-state data output bit 0 (LSB), valid only when CS and RD are both low, with a logic-0 output of 0.4 V max at 1.6 mA. |-| 19 | CLK R | input | RC timing resistor input for the internal clock generator, where heavy capacitive or DC loading should be avoided (loads under 50 pF are allowed). |-| 20 | VCC (or VREF) | power_in | +5 V supply voltage, also the upper reference input to the ladder, with a recommended range of 4.5 V to 5.5 V and an absolute maximum of 6.5 V. |+| 1 | CS | input | Active-low chip select; CS and WR must be low together to start a conversion, and CS and RD both low enable the data outputs. |+| 2 | RD | input | Active-low read strobe that, with CS low, enables the tri-state output latches and resets INTR. |+| 3 | WR | input | Active-low write strobe whose low-to-high transition (with CS low) starts a conversion, and the converter stays in reset while CS and WR are held low. |+| 4 | CLK IN | input | Schmitt-trigger clock input for an external clock (100 kHz to 1460 kHz, 40% to 60% duty cycle) or for an external RC network that sets the internal clock. |+| 5 | INTR | output | Active-low interrupt request that goes high-to-low when a conversion completes and is reset by a read (CS and RD low) at least 8 clock periods after assertion. |+| 6 | VIN(+) | power_in | Non-inverting differential analog input, which must stay within GND - 0.05 V to VCC + 0.05 V. |+| 7 | VIN(-) | power_in | Inverting differential analog input used to offset the zero level; if VIN(-) is greater than or equal to VIN(+) the output code is 0000 0000. |+| 8 | A GND | power_in | Analog ground pin, which should always be wired to the D GND point. |+| 9 | VREF/2 | power_in | Reference voltage input for full-scale adjustment, with an internal gain of 2 so the full-scale differential input is twice this voltage. |+| 10 | D GND | power_in | Digital ground pin, to which the supply bypass capacitor and any self-clocking capacitor should be returned. |+| 11 | DB7 | tri_state | Tri-state latched data output bit 7 (MSB), valid when CS and RD are both low. |+| 12 | DB6 | tri_state | Tri-state latched data output bit 6, valid when CS and RD are both low. |+| 13 | DB5 | tri_state | Tri-state latched data output bit 5, valid when CS and RD are both low. |+| 14 | DB4 | tri_state | Tri-state latched data output bit 4, valid when CS and RD are both low. |+| 15 | DB3 | tri_state | Tri-state latched data output bit 3, valid when CS and RD are both low. |+| 16 | DB2 | tri_state | Tri-state latched data output bit 2, valid when CS and RD are both low. |+| 17 | DB1 | tri_state | Tri-state latched data output bit 1, valid when CS and RD are both low. |+| 18 | DB0 (LSB) | tri_state | Tri-state latched data output bit 0 (LSB), valid when CS and RD are both low. |+| 19 | CLK R | input | RC timing resistor input for the internal clock generator; heavy capacitive or DC loading of this pin should be avoided. |+| 20 | VCC (or VREF) | power_in | +5 V supply voltage, which also serves as the upper reference input to the ladder. |  ## Key specifications @@ -44,51 +44,54 @@ Limits as printed in the datasheet (page.json `metadata.characteristics` carries  | Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page | |---|---|---|---|---|---|---|---|-| Total Unadjusted Error (ADC0804) |  | -1 |  | 1 | LSB | VREF/2=2.500 VDC | 5 |-| Clock Frequency | fCLK | 100 | 640 | 1460 | kHz | VCC = 5V | 5 |-| Clock Duty Cycle |  | 40 |  | 60 | % |  | 5 |-| Conversion Time | TC | 103 |  | 114 | µs | fCLK = 640 kHz | 5 |-| Conversion Time | TC | 66 |  | 73 | 1/fCLK | See (2)(1) | 5 |-| Conversion Rate in Free-Running Mode | CR | 8770 |  | 9708 | conv/s | INTR tied to WR with CS = 0 VDC, fCLK = 640 kHz | 5 |-| Width of WR Input (Start Pulse Width) | tW(WR) | 100 |  |  | ns | CS = 0 VDC | 6 |-| Access Time (Delay from Falling Edge of RD to Output Data Valid) | tACC |  | 135 | 200 | ns | CL = 100 pF | 6 |-| Tri-State Control (Delay from Rising Edge of RD to Hi-Z State) | t1H, t0H |  | 125 | 200 | ns | CL = 10 pF, RL = 10k | 6 |-| Delay from Falling Edge of WR or RD to Reset of INTR | tWI, tRI |  | 300 | 450 | ns |  | 6 |-| Input Capacitance of Logic Control Inputs | CIN |  | 5 | 7.5 | pF |  | 6 |-| Tri-State Output Capacitance (Data Buffers) | COUT |  | 5 | 7.5 | pF |  | 6 |-| Logical 1 Input Voltage (Except Pin 4 CLK IN) | VIN(1) | 2 |  | 15 | V | VCC = 5.25 VDC | 6 |-| Logical 0 Input Voltage (Except Pin 4 CLK IN) | VIN(0) |  |  | 0.8 | V | VCC = 4.75 VDC | 6 |-| Logical 1 Input Current (All Inputs) | IIN(1) | 0.005 |  | 1 | µA | VIN = 5 VDC | 6 |-| Logical 0 Input Current (All Inputs) | IIN(0) | -1 |  | -0.005 | µA | VIN = 0 VDC | 6 |-| CLK IN (Pin 4) Positive Going Threshold Voltage | VT+ | 2.7 | 3.1 | 3.5 | V |  | 6 |-| CLK IN (Pin 4) Negative Going Threshold Voltage | VT− | 1.5 | 1.8 | 2.1 | V |  | 6 |-| CLK IN (Pin 4) Hysteresis (VT+)-(VT−) | VH | 0.6 | 1.3 | 2 | V |  | 6 |-| Logical 0 CLK R Output Voltage | VOUT |  |  | 0.4 | V | IO = 360 µA, VCC = 4.75 VDC | 6 |-| Logical 1 CLK R Output Voltage | VOUT | 2.4 |  |  | V | IO = -360 µA, VCC = 4.75 VDC | 6 |-| Data Outputs Logical 0 Output Voltage | VOUT(0) |  |  | 0.4 | V | IOUT = 1.6 mA, VCC = 4.75 VDC | 6 |-| INTR Output Logical 0 Output Voltage | VOUT(0) |  |  | 0.4 | V | IOUT = 1.0 mA, VCC = 4.75 VDC | 6 |-| Data Outputs Logical 1 Output Voltage | VOUT(1) | 2.4 |  |  | V | IO = -360 µA, VCC = 4.75 VDC | 6 |-| INTR Output Logical 1 Output Voltage | VOUT(1) | 4.5 |  |  | V | IO = -10 µA, VCC = 4.75 VDC | 6 |-| Tri-State Disabled Output Leakage (All Data Buffers) | IOUT | -3 |  |  | µA | VOUT = 0 VDC | 6 |-| Tri-State Disabled Output Leakage (All Data Buffers) | IOUT |  |  | 3 | µA | VOUT = 5 VDC | 6 |-| Output Source Current | ISOURCE | 4.5 | 6 |  | mA | VOUT Short to GND, TA = 25°C | 6 |-| Output Sink Current | ISINK | 9 | 16 |  | mA | VOUT Short to VCC, TA = 25°C | 6 |-| Supply Current (Includes Ladder Current) ADC0804LCN/LCWM | ICC |  | 1.9 | 2.5 | mA | fCLK = 640 kHz, VREF/2 = NC, TA = 25°C and CS = 5 V | 6 |-| Supply voltage (VCC) | VCC |  |  | 6.5 | V |  | 4 |-| Logic control inputs voltage |  | -0.3 |  | 18 | V |  | 4 |-| Voltage at other inputs and outputs |  | -0.3 |  |  | V | max printed as VCC +0.3 | 4 |-| Lead Temperature, Surface Mount Package Vapor Phase (60 seconds) |  |  |  | 215 | °C | Surface mount package, vapor phase, 60 seconds | 4 |-| Lead Temperature, Surface Mount Package Infrared (15 seconds) |  |  |  | 220 | °C | Surface mount package, infrared, 15 seconds | 4 |-| Storage Temperature |  | -65 |  | 150 | °C |  | 4 |-| Package Dissipation |  |  |  | 875 | mW | TA = 25°C | 4 |-| Supply Voltage (VCC) | VCC | 4.5 | 5 | 5.5 | V |  | 4 |-| Operating Free-Air Temperature Range | TA | 0 |  | 70 | °C | ADC0802/04LCWM | 5 |-| Range of VCC (Operating Ratings) | VCC | 4.5 |  | 6.3 | V |  | 5 |-| Junction-to-ambient thermal resistance (RθJA) | RθJA |  | 63.8 |  | °C/W | DW (SOIC) package | 4 |-| Junction-to-case (top) thermal resistance (RθJC(top)) | RθJC(top) |  | 27.2 |  | °C/W | DW (SOIC) package | 4 |-| Junction-to-board thermal resistance (RθJB) | RθJB |  | 31.8 |  | °C/W | DW (SOIC) package | 4 |-| Junction-to-top characterization parameter (ψJT) | ψJT |  | 5.7 |  | °C/W | DW (SOIC) package | 4 |-| Junction-to-board characterization parameter (ψJB) | ψJB |  | 31.3 |  | °C/W | DW (SOIC) package | 4 |+| Supply voltage (VCC) absolute maximum | VCC |  |  | 6.5 | V |  | 4 |+| Logic control inputs voltage |  | -0.3 |  | 18 | V | Logic control inputs | 4 |+| Voltage at other inputs and outputs |  | -0.3 |  |  | V |  | 4 |+| Lead temperature, surface mount package vapor phase |  |  |  | 215 | °C | Vapor phase (60 seconds) | 4 |+| Lead temperature, surface mount package infrared |  |  |  | 220 | °C | Infrared (15 seconds) | 4 |+| Storage temperature |  | -65 |  | 150 | °C |  | 4 |+| Package dissipation at TA = 25°C |  |  |  | 875 | mW | TA = 25°C | 4 |+| Supply voltage (VCC) recommended | VCC | 4.5 | 5 | 5.5 | V |  | 4 |+| Analog input voltage (recommended) |  | -0.05 |  |  | V |  | 4 |+| Operating free-air temperature range (ADC0804LCWM) |  | 0 |  | 70 | °C |  | 5 |+| Range of VCC (operating rating) | VCC | 4.5 |  | 6.3 | V |  | 5 |+| Total Unadjusted Error (ADC0804) |  | -1 |  | 1 | LSB | VREF/2 = 2.500 VDC | 5 |+| VREF/2 Input Resistance (ADC0804) |  | 0.75 | 1.1 |  | kΩ |  | 5 |+| Analog Input Voltage Range V(+) or V(-) |  | -0.05 |  |  | V |  | 5 |+| Conversion time (fCLK = 640 kHz) | TC | 103 |  | 114 | µs | fCLK = 640 kHz | 5 |+| Conversion time (in clock periods) | TC | 66 |  | 73 | 1/fCLK | See (2) | 5 |+| Clock frequency | fCLK | 100 | 640 | 1460 | kHz | VCC = 5V | 5 |+| Clock duty cycle |  | 40 |  | 60 | % |  | 5 |+| Conversion rate in free-running mode | CR | 8770 |  | 9708 | conv/s | INTR tied to WR with CS = 0 VDC; fCLK = 640 kHz | 5 |+| Width of WR input (start pulse width) | tW(WR) | 100 |  |  | ns | CS = 0 VDC | 6 |+| Access time (delay from falling edge of RD to output data valid) | tACC |  | 135 | 200 | ns | CL = 100 pF | 6 |+| Tri-state control (delay from rising edge of RD to Hi-Z state) | t1H, t0H |  | 125 | 200 | ns | CL = 10 pF, RL = 10k | 6 |+| Delay from falling edge of WR or RD to reset of INTR | tWI, tRI |  | 300 | 450 | ns |  | 6 |+| Input capacitance of logic control inputs | CIN |  | 5 | 7.5 | pF |  | 6 |+| Tri-state output capacitance (data buffers) | COUT |  | 5 | 7.5 | pF |  | 6 |+| Logical 1 input voltage (except pin 4 CLK IN) | VIN(1) | 2 |  | 15 | VDC | VCC = 5.25 VDC | 6 |+| Logical 0 input voltage (except pin 4 CLK IN) | VIN(0) |  |  | 0.8 | VDC | VCC = 4.75 VDC | 6 |+| Logical 1 input current (all inputs) | IIN(1) |  | 0.005 | 1 | µADC | VIN = 5 VDC | 6 |+| Logical 0 input current (all inputs) | IIN(0) | -1 | -0.005 |  | µADC | VIN = 0 VDC | 6 |+| CLK IN (pin 4) positive going threshold voltage | VT+ | 2.7 | 3.1 | 3.5 | VDC |  | 6 |+| CLK IN (pin 4) negative going threshold voltage | VT− | 1.5 | 1.8 | 2.1 | VDC |  | 6 |+| CLK IN (pin 4) hysteresis (VT+)-(VT−) | VH | 0.6 | 1.3 | 2 | VDC |  | 6 |+| Logical 0 CLK R output voltage | VOUT |  |  | 0.4 | VDC | IO = 360 µA, VCC = 4.75 VDC | 6 |+| Logical 1 CLK R output voltage | VOUT | 2.4 |  |  | VDC | IO = −360 µA, VCC = 4.75 VDC | 6 |+| Data outputs logical 0 output voltage | VOUT(0) |  |  | 0.4 | VDC | IOUT = 1.6 mA, VCC = 4.75 VDC | 6 |+| INTR output logical 0 output voltage | VOUT(0) |  |  | 0.4 | VDC | IOUT = 1.0 mA, VCC = 4.75 VDC | 6 |+| Data outputs and INTR logical 1 output voltage | VOUT(1) | 2.4 |  |  | VDC | IO = −360 µA, VCC = 4.75 VDC | 6 |+| Logical 1 output voltage (low-current) | VOUT(1) | 4.5 |  |  | VDC | IO = −10 µA, VCC = 4.75 VDC | 6 |+| Tri-state disabled output leakage (all data buffers) | IOUT | -3 |  |  | µADC | VOUT = 0 VDC | 6 |+| Tri-state disabled output leakage (all data buffers) | IOUT |  |  | 3 | µADC | VOUT = 5 VDC | 6 |+| Output short-circuit source current | ISOURCE | 4.5 | 6 |  | mADC | VOUT short to GND, TA = 25°C | 6 |+| Output short-circuit sink current | ISINK | 9 | 16 |  | mADC | VOUT short to VCC, TA = 25°C | 6 |+| Supply current (includes ladder current), ADC0804LCN/LCWM | ICC |  | 1.9 | 2.5 | mA | fCLK = 640 kHz, VREF/2 = NC, TA = 25°C and CS = 5 V | 6 |+| Junction-to-ambient thermal resistance (DW SOIC-20) | RθJA |  | 63.8 |  | °C/W |  | 4 |+| Junction-to-case (top) thermal resistance (DW SOIC-20) | RθJC(top) |  | 27.2 |  | °C/W |  | 4 |+| Junction-to-board thermal resistance (DW SOIC-20) | RθJB |  | 31.8 |  | °C/W |  | 4 |+| Junction-to-top characterization parameter (DW SOIC-20) | ψJT |  | 5.7 |  | °C/W |  | 4 |+| Junction-to-board characterization parameter (DW SOIC-20) | ψJB |  | 31.3 |  | °C/W |  | 4 |  ## CAD (KiCad official) @@ -101,7 +104,7 @@ Limits as printed in the datasheet (page.json `metadata.characteristics` carries  Data extracted from the manufacturer datasheet, not a distributor listing: -- **Datasheet:** [Texas Instruments datasheet](https://www.ti.com/lit/ds/symlink/adc0804lcwmx.pdf) (58 pp, sha256 `44bd9e8071ef6612`, retrieved 2026-11-13, tier: manufacturer)+- **Datasheet:** [Texas Instruments datasheet](https://www.ti.com/lit/ds/symlink/adc0804lcwmx.pdf) (58 pp, sha256 `44bd9e8071ef6612`, retrieved 2026-11-17) - **Extractor:** parts-factory `2.0.0` / `extract_pins 0.3`, primary `claude-haiku-5-5` (text), consensus `claude-sonnet-5-5` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - **CAD:** KiCad official libraries (CC-BY-SA 4.0). 
adc0804lcwmx-hero.glb
⋯ 1 unchanged line ⋯
adc0804lcwmx-hero.overlay.json+522−527
@@ -1,529 +1,524 @@ {- "spec": "adom-hero 1.4",- "mpn": "ADC0804LCWMX",- "kind": "component + footprint reference art",- "board_use": false,- "plane_z_mm": -0.02,- "units": "metre",- "upAxis": "Z",- "layers": {-  "pad_outlines": {-   "material": "Footprint pads - teal dashed outlines - 50 percent opacity",-   "rgba": [-    0.0,-    0.902,-    0.863,-    0.5-   ],-   "pads": 20,-   "span_mm": 12.03,-   "dash_mm": 0.3008,-   "gap_mm": 0.1804,-   "pad_stroke_mm": 0.0722-  },-  "silkscreen": {-   "material": "Silkscreen reference lines - 30 percent opacity",-   "rgba": [-    0.92,-    0.96,-    1.0,-    0.3-   ],-   "footprint_items": 7,-   "pin1": {-    "source": "footprint silkscreen",-    "pad": "1"-   }-  },-  "signal_names": {-   "material": "Signal names - 50 percent opacity",-   "rgba": [-    0.92,-    0.96,-    1.0,-    0.5-   ],-   "font": "DejaVu Sans Mono",-   "labels": 20,-   "sides": "top + mirrored underside (single-sided)",-   "omitted": null,-   "fallback_to_pad_number": 0-  }- },- "align": {-  "ok": true,-  "board_underside": true,-  "electrical_pads_without_contact": [],-  "mounting_pads_left_out": [],-  "centre_offset_mm": 0.0,-  "over_pads": true,-  "tolerance_mm": 0.962,-  "orientation_flipped": false,-  "contacts_bbox_mm": [-   -5.15,-   5.15,-   -5.92,-   5.92-  ],-  "pads_bbox_mm": [-   -5.675,-   5.675,-   -6.015,-   6.015+  "spec": "adom-hero 1.4",+  "mpn": "ADC0804LCWMX",+  "kind": "component + footprint reference art",+  "board_use": false,+  "plane_z_mm": -0.02,+  "units": "metre",+  "upAxis": "Z",+  "layers": {+    "pad_outlines": {+      "material": "Footprint pads - teal dashed outlines - 50 percent opacity",+      "rgba": [+        0.0,+        0.902,+        0.863,+        0.5+      ],+      "pads": 20,+      "span_mm": 12.03,+      "dash_mm": 0.3008,+      "gap_mm": 0.1804,+      "pad_stroke_mm": 0.0722+    },+    "silkscreen": {+      "material": "Silkscreen reference lines - 30 percent opacity",+      "rgba": [+        0.92,+        0.96,+        1.0,+        0.3+      ],+      "footprint_items": 7,+      "pin1": {+        "source": "footprint silkscreen",+        "pad": "1"+      }+    },+    "signal_names": {+      "material": "Signal names - 50 percent opacity",+      "rgba": [+        0.92,+        0.96,+        1.0,+        0.5+      ],+      "font": "DejaVu Sans Mono",+      "labels": 20,+      "sides": "top + mirrored underside (single-sided)",+      "fallback_to_pad_number": 0+    }+  },+  "align": {+    "ok": true,+    "centre_offset_mm": 0.0,+    "tolerance_mm": 0.962,+    "orientation_flipped": false,+    "contacts_bbox_mm": [+      -5.15,+      5.15,+      -5.92,+      5.92+    ],+    "pads_bbox_mm": [+      -5.675,+      5.675,+      -6.015,+      6.015+    ],+    "seating_z_mm": -0.0+  },+  "sources": {+    "glb": "adc0804lcwmx-etched.glb",+    "glb_sha256": "4cdff50796fabf2b874f7cd9ae0560b970cfa9ee863735625981130db0473102",+    "footprint": "adc0804lcwmx.kicad_mod",+    "footprint_sha256": "9783bc19f518a72442ddbfe6289e767a42c3d23358b65c3447b6a36bdd0e7dcf",+    "pins": "page.json component.pins",+    "pins_sha256": "7fecf7ee9db47a0de5f5f029c9fa4a6be3e1386fb1becf9ce4258f72e5cc242c"+  },+  "generator": "adom-wiki 1.8.28 (component_hero)",+  "labels": [+    {+      "pad": "1",+      "text": "CS",+      "x": -5.825,+      "y": -5.715,+      "align": "right",+      "vertical": false,+      "h": 0.6+    },+    {+      "pad": "2",+      "text": "RD",+      "x": -5.825,+      "y": -4.445,+      "align": "right",+      "vertical": false,+      "h": 0.6+    },+    {+      "pad": "3",+      "text": "WR",+      "x": -5.825,+      "y": -3.175,+      "align": "right",+      "vertical": false,+      "h": 0.6+    },+    {+      "pad": "4",+      "text": "CLK IN",+      "x": -5.825,+      "y": -1.905,+      "align": "right",+      "vertical": false,+      "h": 0.6+    },+    {+      "pad": "5",+      "text": "INTR",+      "x": -5.825,+      "y": -0.635,+      "align": "right",+      "vertical": false,+      "h": 0.6+    },+    {+      "pad": "6",+      "text": "VIN(+)",+      "x": -5.825,+      "y": 0.635,+      "align": "right",+      "vertical": false,+      "h": 0.6+    },+    {+      "pad": "7",+      "text": "VIN(-)",+      "x": -5.825,+      "y": 1.905,+      "align": "right",+      "vertical": false,+      "h": 0.6+    },+    {+      "pad": "8",+      "text": "A GND",+      "x": -5.825,+      "y": 3.175,+      "align": "right",+      "vertical": false,+      "h": 0.6+    },+    {+      "pad": "9",+      "text": "VREF/2",+      "x": -5.825,+      "y": 4.445,+      "align": "right",+      "vertical": false,+      "h": 0.6+    },+    {+      "pad": "10",+      "text": "D GND",+      "x": -5.825,+      "y": 5.715,+      "align": "right",+      "vertical": false,+      "h": 0.6+    },+    {+      "pad": "11",+      "text": "DB7",+      "x": 5.825,+      "y": 5.715,+      "align": "left",+      "vertical": false,+      "h": 0.6+    },+    {+      "pad": "12",+      "text": "DB6",+      "x": 5.825,+      "y": 4.445,+      "align": "left",+      "vertical": false,+      "h": 0.6+    },+    {+      "pad": "13",+      "text": "DB5",+      "x": 5.825,+      "y": 3.175,+      "align": "left",+      "vertical": false,+      "h": 0.6+    },+    {+      "pad": "14",+      "text": "DB4",+      "x": 5.825,+      "y": 1.905,+      "align": "left",+      "vertical": false,+      "h": 0.6+    },+    {+      "pad": "15",+      "text": "DB3",+      "x": 5.825,+      "y": 0.635,+      "align": "left",+      "vertical": false,+      "h": 0.6+    },+    {+      "pad": "16",+      "text": "DB2",+      "x": 5.825,+      "y": -0.635,+      "align": "left",+      "vertical": false,+      "h": 0.6+    },+    {+      "pad": "17",+      "text": "DB1",+      "x": 5.825,+      "y": -1.905,+      "align": "left",+      "vertical": false,+      "h": 0.6+    },+    {+      "pad": "18",+      "text": "DB0 (LSB)",+      "x": 5.825,+      "y": -3.175,+      "align": "left",+      "vertical": false,+      "h": 0.6+    },+    {+      "pad": "19",+      "text": "CLK R",+      "x": 5.825,+      "y": -4.445,+      "align": "left",+      "vertical": false,+      "h": 0.6+    },+    {+      "pad": "20",+      "text": "VCC (or VREF)",+      "x": 5.825,+      "y": -5.715,+      "align": "left",+      "vertical": false,+      "h": 0.6+    }   ],-  "seating_z_mm": -0.0- },- "sources": {-  "glb": "adc0804lcwmx-etched.glb",-  "glb_sha256": "4cdff50796fabf2b874f7cd9ae0560b970cfa9ee863735625981130db0473102",-  "footprint": "adc0804lcwmx.kicad_mod",-  "footprint_sha256": "9783bc19f518a72442ddbfe6289e767a42c3d23358b65c3447b6a36bdd0e7dcf",-  "pins": "page.json component.pins",-  "pins_sha256": "611f0a3ffdf7befbb4251fcafdbce254db8d95f49df07185c1517fc600f3f0a0"- },- "generator": "factory/hero_glb.py",- "labels": [-  {-   "pad": "1",-   "text": "CS",-   "x": -5.825,-   "y": -5.715,-   "align": "right",-   "vertical": false,-   "h": 0.6-  },-  {-   "pad": "2",-   "text": "RD",-   "x": -5.825,-   "y": -4.445,-   "align": "right",-   "vertical": false,-   "h": 0.6-  },-  {-   "pad": "3",-   "text": "WR",-   "x": -5.825,-   "y": -3.175,-   "align": "right",-   "vertical": false,-   "h": 0.6-  },-  {-   "pad": "4",-   "text": "CLK IN",-   "x": -5.825,-   "y": -1.905,-   "align": "right",-   "vertical": false,-   "h": 0.6-  },-  {-   "pad": "5",-   "text": "INTR",-   "x": -5.825,-   "y": -0.635,-   "align": "right",-   "vertical": false,-   "h": 0.6-  },-  {-   "pad": "6",-   "text": "VIN(+)",-   "x": -5.825,-   "y": 0.635,-   "align": "right",-   "vertical": false,-   "h": 0.6-  },-  {-   "pad": "7",-   "text": "VIN(\u2013)",-   "x": -5.825,-   "y": 1.905,-   "align": "right",-   "vertical": false,-   "h": 0.6-  },-  {-   "pad": "8",-   "text": "A GND",-   "x": -5.825,-   "y": 3.175,-   "align": "right",-   "vertical": false,-   "h": 0.6-  },-  {-   "pad": "9",-   "text": "VREF/2",-   "x": -5.825,-   "y": 4.445,-   "align": "right",-   "vertical": false,-   "h": 0.6-  },-  {-   "pad": "10",-   "text": "D GND",-   "x": -5.825,-   "y": 5.715,-   "align": "right",-   "vertical": false,-   "h": 0.6-  },-  {-   "pad": "11",-   "text": "DB7",-   "x": 5.825,-   "y": 5.715,-   "align": "left",-   "vertical": false,-   "h": 0.6-  },-  {-   "pad": "12",-   "text": "DB6",-   "x": 5.825,-   "y": 4.445,-   "align": "left",-   "vertical": false,-   "h": 0.6-  },-  {-   "pad": "13",-   "text": "DB5",-   "x": 5.825,-   "y": 3.175,-   "align": "left",-   "vertical": false,-   "h": 0.6-  },-  {-   "pad": "14",-   "text": "DB4",-   "x": 5.825,-   "y": 1.905,-   "align": "left",-   "vertical": false,-   "h": 0.6-  },-  {-   "pad": "15",-   "text": "DB3",-   "x": 5.825,-   "y": 0.635,-   "align": "left",-   "vertical": false,-   "h": 0.6-  },-  {-   "pad": "16",-   "text": "DB2",-   "x": 5.825,-   "y": -0.635,-   "align": "left",-   "vertical": false,-   "h": 0.6-  },-  {-   "pad": "17",-   "text": "DB1",-   "x": 5.825,-   "y": -1.905,-   "align": "left",-   "vertical": false,-   "h": 0.6-  },-  {-   "pad": "18",-   "text": "DB0 (LSB)",-   "x": 5.825,-   "y": -3.175,-   "align": "left",-   "vertical": false,-   "h": 0.6-  },-  {-   "pad": "19",-   "text": "CLK R",-   "x": 5.825,-   "y": -4.445,-   "align": "left",-   "vertical": false,-   "h": 0.6-  },-  {-   "pad": "20",-   "text": "VCC (or VREF)",-   "x": 5.825,-   "y": -5.715,-   "align": "left",-   "vertical": false,-   "h": 0.6-  }- ],- "pads": [-  {-   "number": "1",-   "shape": "roundrect",-   "center_mm": [-    -4.65,-    -5.715-   ],-   "size_mm": [-    2.05,-    0.6-   ],-   "rot": 0.0-  },-  {-   "number": "2",-   "shape": "roundrect",-   "center_mm": [-    -4.65,-    -4.445-   ],-   "size_mm": [-    2.05,-    0.6-   ],-   "rot": 0.0-  },-  {-   "number": "3",-   "shape": "roundrect",-   "center_mm": [-    -4.65,-    -3.175-   ],-   "size_mm": [-    2.05,-    0.6-   ],-   "rot": 0.0-  },-  {-   "number": "4",-   "shape": "roundrect",-   "center_mm": [-    -4.65,-    -1.905-   ],-   "size_mm": [-    2.05,-    0.6-   ],-   "rot": 0.0-  },-  {-   "number": "5",-   "shape": "roundrect",-   "center_mm": [-    -4.65,-    -0.635-   ],-   "size_mm": [-    2.05,-    0.6-   ],-   "rot": 0.0-  },-  {-   "number": "6",-   "shape": "roundrect",-   "center_mm": [-    -4.65,-    0.635-   ],-   "size_mm": [-    2.05,-    0.6-   ],-   "rot": 0.0-  },-  {-   "number": "7",-   "shape": "roundrect",-   "center_mm": [-    -4.65,-    1.905-   ],-   "size_mm": [-    2.05,-    0.6-   ],-   "rot": 0.0-  },-  {-   "number": "8",-   "shape": "roundrect",-   "center_mm": [-    -4.65,-    3.175-   ],-   "size_mm": [-    2.05,-    0.6-   ],-   "rot": 0.0-  },-  {-   "number": "9",-   "shape": "roundrect",-   "center_mm": [-    -4.65,-    4.445-   ],-   "size_mm": [-    2.05,-    0.6-   ],-   "rot": 0.0-  },-  {-   "number": "10",-   "shape": "roundrect",-   "center_mm": [-    -4.65,-    5.715-   ],-   "size_mm": [-    2.05,-    0.6-   ],-   "rot": 0.0-  },-  {-   "number": "11",-   "shape": "roundrect",-   "center_mm": [-    4.65,-    5.715-   ],-   "size_mm": [-    2.05,-    0.6-   ],-   "rot": 0.0-  },-  {-   "number": "12",-   "shape": "roundrect",-   "center_mm": [-    4.65,-    4.445-   ],-   "size_mm": [-    2.05,-    0.6-   ],-   "rot": 0.0-  },-  {-   "number": "13",-   "shape": "roundrect",-   "center_mm": [-    4.65,-    3.175-   ],-   "size_mm": [-    2.05,-    0.6-   ],-   "rot": 0.0-  },-  {-   "number": "14",-   "shape": "roundrect",-   "center_mm": [-    4.65,-    1.905-   ],-   "size_mm": [-    2.05,-    0.6-   ],-   "rot": 0.0-  },-  {-   "number": "15",-   "shape": "roundrect",-   "center_mm": [-    4.65,-    0.635-   ],-   "size_mm": [-    2.05,-    0.6-   ],-   "rot": 0.0-  },-  {-   "number": "16",-   "shape": "roundrect",-   "center_mm": [-    4.65,-    -0.635-   ],-   "size_mm": [-    2.05,-    0.6-   ],-   "rot": 0.0-  },-  {-   "number": "17",-   "shape": "roundrect",-   "center_mm": [-    4.65,-    -1.905-   ],-   "size_mm": [-    2.05,-    0.6-   ],-   "rot": 0.0-  },-  {-   "number": "18",-   "shape": "roundrect",-   "center_mm": [-    4.65,-    -3.175-   ],-   "size_mm": [-    2.05,-    0.6-   ],-   "rot": 0.0-  },-  {-   "number": "19",-   "shape": "roundrect",-   "center_mm": [-    4.65,-    -4.445-   ],-   "size_mm": [-    2.05,-    0.6-   ],-   "rot": 0.0-  },-  {-   "number": "20",-   "shape": "roundrect",-   "center_mm": [-    4.65,-    -5.715-   ],-   "size_mm": [-    2.05,-    0.6-   ],-   "rot": 0.0-  }- ]-}\ No newline at end of file+  "pads": [+    {+      "number": "1",+      "shape": "roundrect",+      "center_mm": [+        -4.65,+        -5.715+      ],+      "size_mm": [+        2.05,+        0.6+      ],+      "rot": 0.0+    },+    {+      "number": "2",+      "shape": "roundrect",+      "center_mm": [+        -4.65,+        -4.445+      ],+      "size_mm": [+        2.05,+        0.6+      ],+      "rot": 0.0+    },+    {+      "number": "3",+      "shape": "roundrect",+      "center_mm": [+        -4.65,+        -3.175+      ],+      "size_mm": [+        2.05,+        0.6+      ],+      "rot": 0.0+    },+    {+      "number": "4",+      "shape": "roundrect",+      "center_mm": [+        -4.65,+        -1.905+      ],+      "size_mm": [+        2.05,+        0.6+      ],+      "rot": 0.0+    },+    {+      "number": "5",+      "shape": "roundrect",+      "center_mm": [+        -4.65,+        -0.635+      ],+      "size_mm": [+        2.05,+        0.6+      ],+      "rot": 0.0+    },+    {+      "number": "6",+      "shape": "roundrect",+      "center_mm": [+        -4.65,+        0.635+      ],+      "size_mm": [+        2.05,+        0.6+      ],+      "rot": 0.0+    },+    {+      "number": "7",+      "shape": "roundrect",+      "center_mm": [+        -4.65,+        1.905+      ],+      "size_mm": [+        2.05,+        0.6+      ],+      "rot": 0.0+    },+    {+      "number": "8",+      "shape": "roundrect",+      "center_mm": [+        -4.65,+        3.175+      ],+      "size_mm": [+        2.05,+        0.6+      ],+      "rot": 0.0+    },+    {+      "number": "9",+      "shape": "roundrect",+      "center_mm": [+        -4.65,+        4.445+      ],+      "size_mm": [+        2.05,+        0.6+      ],+      "rot": 0.0+    },+    {+      "number": "10",+      "shape": "roundrect",+      "center_mm": [+        -4.65,+        5.715+      ],+      "size_mm": [+        2.05,+        0.6+      ],+      "rot": 0.0+    },+    {+      "number": "11",+      "shape": "roundrect",+      "center_mm": [+        4.65,+        5.715+      ],+      "size_mm": [+        2.05,+        0.6+      ],+      "rot": 0.0+    },+    {+      "number": "12",+      "shape": "roundrect",+      "center_mm": [+        4.65,+        4.445+      ],+      "size_mm": [+        2.05,+        0.6+      ],+      "rot": 0.0+    },+    {+      "number": "13",+      "shape": "roundrect",+      "center_mm": [+        4.65,+        3.175+      ],+      "size_mm": [+        2.05,+        0.6+      ],+      "rot": 0.0+    },+    {+      "number": "14",+      "shape": "roundrect",+      "center_mm": [+        4.65,+        1.905+      ],+      "size_mm": [+        2.05,+        0.6+      ],+      "rot": 0.0+    },+    {+      "number": "15",+      "shape": "roundrect",+      "center_mm": [+        4.65,+        0.635+      ],+      "size_mm": [+        2.05,+        0.6+      ],+      "rot": 0.0+    },+    {+      "number": "16",+      "shape": "roundrect",+      "center_mm": [+        4.65,+        -0.635+      ],+      "size_mm": [+        2.05,+        0.6+      ],+      "rot": 0.0+    },+    {+      "number": "17",+      "shape": "roundrect",+      "center_mm": [+        4.65,+        -1.905+      ],+      "size_mm": [+        2.05,+        0.6+      ],+      "rot": 0.0+    },+    {+      "number": "18",+      "shape": "roundrect",+      "center_mm": [+        4.65,+        -3.175+      ],+      "size_mm": [+        2.05,+        0.6+      ],+      "rot": 0.0+    },+    {+      "number": "19",+      "shape": "roundrect",+      "center_mm": [+        4.65,+        -4.445+      ],+      "size_mm": [+        2.05,+        0.6+      ],+      "rot": 0.0+    },+    {+      "number": "20",+      "shape": "roundrect",+      "center_mm": [+        4.65,+        -5.715+      ],+      "size_mm": [+        2.05,+        0.6+      ],+      "rot": 0.0+    }+  ]+}
adc0804lcwmx.kicad_sym+1−1
@@ -33,7 +33,7 @@       (number "6" (effects (font (size 1.27 1.27))))     )     (pin power_in line (at -17.78 -5.08 0) (length 5.08)-      (name "VIN(–)" (effects (font (size 1.27 1.27))))+      (name "VIN(-)" (effects (font (size 1.27 1.27))))       (number "7" (effects (font (size 1.27 1.27))))     )     (pin power_in line (at -17.78 -7.62 0) (length 5.08)
adc0804lcwmx.lbr+2−2
@@ -111,7 +111,7 @@   <pin name="CLK_IN" x="-17.78" y="2.54" length="middle" direction="in"/>   <pin name="INTR" x="-17.78" y="0" length="middle" direction="out"/>   <pin name="VIN_+" x="-17.78" y="-2.54" length="middle" direction="pwr"/>-  <pin name="VIN" x="-17.78" y="-5.08" length="middle" direction="pwr"/>+  <pin name="VIN_-" x="-17.78" y="-5.08" length="middle" direction="pwr"/>   <pin name="A_GND" x="-17.78" y="-7.62" length="middle" direction="pwr"/>   <pin name="VREF/2" x="-17.78" y="-10.16" length="middle" direction="pwr"/>   <pin name="D_GND" x="-17.78" y="-12.7" length="middle" direction="pwr"/>@@ -142,7 +142,7 @@         <connect gate="G$1" pin="CLK_IN" pad="4"/>         <connect gate="G$1" pin="INTR" pad="5"/>         <connect gate="G$1" pin="VIN_+" pad="6"/>-        <connect gate="G$1" pin="VIN" pad="7"/>+        <connect gate="G$1" pin="VIN_-" pad="7"/>         <connect gate="G$1" pin="A_GND" pad="8"/>         <connect gate="G$1" pin="VREF/2" pad="9"/>         <connect gate="G$1" pin="D_GND" pad="10"/>
package.json+32−31
@@ -1,6 +1,6 @@ {   "slug": "adc0804lcwmx",-  "version": "0.1.2",+  "version": "0.1.3",   "type": "component",   "description": "Texas Instruments Pre-ordered Chips, SOIC-20-300mil. Pinout cross-checked by two models against the datasheet, KiCad symbol/footprint/3D.",   "tags": [@@ -53,7 +53,7 @@       "mouser": "926-ADC0804LCWMX"     },     "distributor_check": {-      "checked_at": "2026-11-13T01:56:24Z",+      "checked_at": "2026-11-17T23:13:27Z",       "source": "Component Ocean /api/assign-pns",       "digikey": {         "pn": "296-36292-2-ND",@@ -69,121 +69,121 @@         "number": "1",         "name": "CS",         "type": "input",-        "description": "Active-low chip select; CS and WR must both be low to start a conversion, and the datasheet assumes CS brackets the WR strobe."+        "description": "Active-low chip select; CS and WR must be low together to start a conversion, and CS and RD both low enable the data outputs."       },       {         "number": "2",         "name": "RD",         "type": "input",-        "description": "Active-low read strobe that, with CS low, resets INTR and enables the tri-state output latches onto DB0 to DB7."+        "description": "Active-low read strobe that, with CS low, enables the tri-state output latches and resets INTR."       },       {         "number": "3",         "name": "WR",         "type": "input",-        "description": "Active-low write strobe; the conversion starts on the low-to-high transition of WR while CS is low, and the WR pulse width must be at least 100 ns."+        "description": "Active-low write strobe whose low-to-high transition (with CS low) starts a conversion, and the converter stays in reset while CS and WR are held low."       },       {         "number": "4",         "name": "CLK IN",         "type": "input",-        "description": "Clock input to a Schmitt trigger for an external clock of 100 kHz to 1460 kHz (640 kHz for specified accuracy, 40% to 60% duty cycle), or used with an external RC for self-clocking."+        "description": "Schmitt-trigger clock input for an external clock (100 kHz to 1460 kHz, 40% to 60% duty cycle) or for an external RC network that sets the internal clock."       },       {         "number": "5",         "name": "INTR",         "type": "output",-        "description": "Active-low interrupt request output that goes high-to-low at the end of a conversion and can be tied to WR for free-running operation."+        "description": "Active-low interrupt request that goes high-to-low when a conversion completes and is reset by a read (CS and RD low) at least 8 clock periods after assertion."       },       {         "number": "6",         "name": "VIN(+)",         "type": "power_in",-        "description": "Positive differential analog input that must stay within GND - 0.05 V to VCC + 0.05 V, with input currents above 1 mA requiring an external diode."+        "description": "Non-inverting differential analog input, which must stay within GND - 0.05 V to VCC + 0.05 V."       },       {         "number": "7",-        "name": "VIN(–)",+        "name": "VIN(-)",         "type": "power_in",-        "description": "Negative differential analog input used for offset (tare) correction, with the same GND - 0.05 V to VCC + 0.05 V range, and the output code is 00 hex when VIN(-) is at or above VIN(+)."+        "description": "Inverting differential analog input used to offset the zero level; if VIN(-) is greater than or equal to VIN(+) the output code is 0000 0000."       },       {         "number": "8",         "name": "A GND",         "type": "power_in",-        "description": "Analog ground pin that should be wired to a single point separate from the logic ground and tied to D GND as the datasheet specifies."+        "description": "Analog ground pin, which should always be wired to the D GND point."       },       {         "number": "9",         "name": "VREF/2",         "type": "power_in",-        "description": "Reference voltage input for full-scale adjustment with an internal gain of 2, so the full-scale span is twice the voltage on this pin, and it defaults to VCC/2 when unconnected."+        "description": "Reference voltage input for full-scale adjustment, with an internal gain of 2 so the full-scale differential input is twice this voltage."       },       {         "number": "10",         "name": "D GND",         "type": "power_in",-        "description": "Digital ground pin for the logic and output drivers, to which the supply bypass capacitor should return."+        "description": "Digital ground pin, to which the supply bypass capacitor and any self-clocking capacitor should be returned."       },       {         "number": "11",         "name": "DB7",         "type": "tri_state",-        "description": "Tri-state data output bit 7 (MSB), valid only when CS and RD are both low, with a logic-0 output of 0.4 V max at 1.6 mA."+        "description": "Tri-state latched data output bit 7 (MSB), valid when CS and RD are both low."       },       {         "number": "12",         "name": "DB6",         "type": "tri_state",-        "description": "Tri-state data output bit 6, valid only when CS and RD are both low, with a logic-0 output of 0.4 V max at 1.6 mA."+        "description": "Tri-state latched data output bit 6, valid when CS and RD are both low."       },       {         "number": "13",         "name": "DB5",         "type": "tri_state",-        "description": "Tri-state data output bit 5, valid only when CS and RD are both low, with a logic-0 output of 0.4 V max at 1.6 mA."+        "description": "Tri-state latched data output bit 5, valid when CS and RD are both low."       },       {         "number": "14",         "name": "DB4",         "type": "tri_state",-        "description": "Tri-state data output bit 4, valid only when CS and RD are both low, with a logic-0 output of 0.4 V max at 1.6 mA."+        "description": "Tri-state latched data output bit 4, valid when CS and RD are both low."       },       {         "number": "15",         "name": "DB3",         "type": "tri_state",-        "description": "Tri-state data output bit 3, valid only when CS and RD are both low, with a logic-0 output of 0.4 V max at 1.6 mA."+        "description": "Tri-state latched data output bit 3, valid when CS and RD are both low."       },       {         "number": "16",         "name": "DB2",         "type": "tri_state",-        "description": "Tri-state data output bit 2, valid only when CS and RD are both low, with a logic-0 output of 0.4 V max at 1.6 mA."+        "description": "Tri-state latched data output bit 2, valid when CS and RD are both low."       },       {         "number": "17",         "name": "DB1",         "type": "tri_state",-        "description": "Tri-state data output bit 1, valid only when CS and RD are both low, with a logic-0 output of 0.4 V max at 1.6 mA."+        "description": "Tri-state latched data output bit 1, valid when CS and RD are both low."       },       {         "number": "18",         "name": "DB0 (LSB)",         "type": "tri_state",-        "description": "Tri-state data output bit 0 (LSB), valid only when CS and RD are both low, with a logic-0 output of 0.4 V max at 1.6 mA."+        "description": "Tri-state latched data output bit 0 (LSB), valid when CS and RD are both low."       },       {         "number": "19",         "name": "CLK R",         "type": "input",-        "description": "RC timing resistor input for the internal clock generator, where heavy capacitive or DC loading should be avoided (loads under 50 pF are allowed)."+        "description": "RC timing resistor input for the internal clock generator; heavy capacitive or DC loading of this pin should be avoided."       },       {         "number": "20",         "name": "VCC (or VREF)",         "type": "power_in",-        "description": "+5 V supply voltage, also the upper reference input to the ladder, with a recommended range of 4.5 V to 5.5 V and an absolute maximum of 6.5 V."+        "description": "+5 V supply voltage, which also serves as the upper reference input to the ladder."       }     ],     "provenance": {@@ -197,17 +197,18 @@         "consensus": "agreed",         "guards": "pin_guards 0.1: passed",         "guard_notes": [-          "extractor flagged: The datasheet pin table labels DB0 to DB7 as 'O' (output), but the text describes them as tri-state ; The datasheet pin table labels CLK R as 'I' (input), but it is an RC timing pin for the internal clo; The pinout is taken from the page-3 table, which covers both the NFH (PDIP) and DW (SOIC) packages w"+          "extractor flagged: The datasheet pin table labels the DB outputs as 'O' and pin 20 as 'I'; I mapped the DB outputs to t; The datasheet pin table types CLK R as an input, but the text does not give a valid timing resistor "         ],         "pages_sent": 58,-        "cost_usd": 0.1879,-        "at": "2026-11-13T01:56:12"+        "cost_usd": 0.1858,+        "at": "2026-11-17T23:12:44"       },       "datasheet": {         "url": "https://www.ti.com/lit/ds/symlink/adc0804lcwmx.pdf",         "pages": 58,         "sha256": "44bd9e8071ef6612",-        "source_tier": "mfr"+        "source_tier": "mfr",+        "citation": "Texas Instruments datasheet"       },       "cad": "KiCad official (CC-BY-SA 4.0)",       "pins": {@@ -238,7 +239,7 @@         "centre_offset_mm": 0.0,         "footprint_binding": "identity",         "sha256": "59a10b341e6972b31d81802a048060326da627d8b92dcf4263064f4f62ec808e",-        "checked": "2026-11-13",+        "checked": "2026-11-17",         "checked_by": "factory/step_pose.py (Z-up, origin, seat, binding)"       },       {@@ -256,13 +257,13 @@         "zmin_mm": -0.0,         "centre_offset_mm": 0.0,         "footprint_binding": "identity",-        "sha256": "2bd4bfeb9f9d2ce05e515489f8ef859e97685380af1b2379e72e5f6964829ae2",-        "checked": "2026-11-13",+        "sha256": "b876c4187f18011bc5ebe9c2737c57f3db94993ba24dc9528cc377ceec5100ad",+        "checked": "2026-11-17",         "checked_by": "factory/step_pose.py (Z-up, origin, seat, binding)"       }     ],     "package_dims": {-      "package_code": "DW",+      "package_code": "DW0020A",       "source_page": 55,       "D": {         "nom_mm": 12.8,
page.json+35−32
@@ -4,7 +4,7 @@   "slug": "adc0804lcwmx",   "title": "ADC0804LCWMX",   "brief": "Texas Instruments Pre-ordered Chips, SOIC-20-300mil. Pinout cross-checked by two models against the datasheet, KiCad symbol/footprint/3D.",-  "version": "0.1.2",+  "version": "0.1.3",   "license": "CC-BY-SA-4.0",   "tags": [     "component",@@ -36,7 +36,7 @@       "mouser": "926-ADC0804LCWMX"     },     "distributor_check": {-      "checked_at": "2026-11-13T01:56:24Z",+      "checked_at": "2026-11-17T23:13:27Z",       "source": "Component Ocean /api/assign-pns",       "digikey": {         "pn": "296-36292-2-ND",@@ -52,121 +52,121 @@         "number": "1",         "name": "CS",         "type": "input",-        "description": "Active-low chip select; CS and WR must both be low to start a conversion, and the datasheet assumes CS brackets the WR strobe."+        "description": "Active-low chip select; CS and WR must be low together to start a conversion, and CS and RD both low enable the data outputs."       },       {         "number": "2",         "name": "RD",         "type": "input",-        "description": "Active-low read strobe that, with CS low, resets INTR and enables the tri-state output latches onto DB0 to DB7."+        "description": "Active-low read strobe that, with CS low, enables the tri-state output latches and resets INTR."       },       {         "number": "3",         "name": "WR",         "type": "input",-        "description": "Active-low write strobe; the conversion starts on the low-to-high transition of WR while CS is low, and the WR pulse width must be at least 100 ns."+        "description": "Active-low write strobe whose low-to-high transition (with CS low) starts a conversion, and the converter stays in reset while CS and WR are held low."       },       {         "number": "4",         "name": "CLK IN",         "type": "input",-        "description": "Clock input to a Schmitt trigger for an external clock of 100 kHz to 1460 kHz (640 kHz for specified accuracy, 40% to 60% duty cycle), or used with an external RC for self-clocking."+        "description": "Schmitt-trigger clock input for an external clock (100 kHz to 1460 kHz, 40% to 60% duty cycle) or for an external RC network that sets the internal clock."       },       {         "number": "5",         "name": "INTR",         "type": "output",-        "description": "Active-low interrupt request output that goes high-to-low at the end of a conversion and can be tied to WR for free-running operation."+        "description": "Active-low interrupt request that goes high-to-low when a conversion completes and is reset by a read (CS and RD low) at least 8 clock periods after assertion."       },       {         "number": "6",         "name": "VIN(+)",         "type": "power_in",-        "description": "Positive differential analog input that must stay within GND - 0.05 V to VCC + 0.05 V, with input currents above 1 mA requiring an external diode."+        "description": "Non-inverting differential analog input, which must stay within GND - 0.05 V to VCC + 0.05 V."       },       {         "number": "7",-        "name": "VIN(–)",+        "name": "VIN(-)",         "type": "power_in",-        "description": "Negative differential analog input used for offset (tare) correction, with the same GND - 0.05 V to VCC + 0.05 V range, and the output code is 00 hex when VIN(-) is at or above VIN(+)."+        "description": "Inverting differential analog input used to offset the zero level; if VIN(-) is greater than or equal to VIN(+) the output code is 0000 0000."       },       {         "number": "8",         "name": "A GND",         "type": "power_in",-        "description": "Analog ground pin that should be wired to a single point separate from the logic ground and tied to D GND as the datasheet specifies."+        "description": "Analog ground pin, which should always be wired to the D GND point."       },       {         "number": "9",         "name": "VREF/2",         "type": "power_in",-        "description": "Reference voltage input for full-scale adjustment with an internal gain of 2, so the full-scale span is twice the voltage on this pin, and it defaults to VCC/2 when unconnected."+        "description": "Reference voltage input for full-scale adjustment, with an internal gain of 2 so the full-scale differential input is twice this voltage."       },       {         "number": "10",         "name": "D GND",         "type": "power_in",-        "description": "Digital ground pin for the logic and output drivers, to which the supply bypass capacitor should return."+        "description": "Digital ground pin, to which the supply bypass capacitor and any self-clocking capacitor should be returned."       },       {         "number": "11",         "name": "DB7",         "type": "tri_state",-        "description": "Tri-state data output bit 7 (MSB), valid only when CS and RD are both low, with a logic-0 output of 0.4 V max at 1.6 mA."+        "description": "Tri-state latched data output bit 7 (MSB), valid when CS and RD are both low."       },       {         "number": "12",         "name": "DB6",         "type": "tri_state",-        "description": "Tri-state data output bit 6, valid only when CS and RD are both low, with a logic-0 output of 0.4 V max at 1.6 mA."+        "description": "Tri-state latched data output bit 6, valid when CS and RD are both low."       },       {         "number": "13",         "name": "DB5",         "type": "tri_state",-        "description": "Tri-state data output bit 5, valid only when CS and RD are both low, with a logic-0 output of 0.4 V max at 1.6 mA."+        "description": "Tri-state latched data output bit 5, valid when CS and RD are both low."       },       {         "number": "14",         "name": "DB4",         "type": "tri_state",-        "description": "Tri-state data output bit 4, valid only when CS and RD are both low, with a logic-0 output of 0.4 V max at 1.6 mA."+        "description": "Tri-state latched data output bit 4, valid when CS and RD are both low."       },       {         "number": "15",         "name": "DB3",         "type": "tri_state",-        "description": "Tri-state data output bit 3, valid only when CS and RD are both low, with a logic-0 output of 0.4 V max at 1.6 mA."+        "description": "Tri-state latched data output bit 3, valid when CS and RD are both low."       },       {         "number": "16",         "name": "DB2",         "type": "tri_state",-        "description": "Tri-state data output bit 2, valid only when CS and RD are both low, with a logic-0 output of 0.4 V max at 1.6 mA."+        "description": "Tri-state latched data output bit 2, valid when CS and RD are both low."       },       {         "number": "17",         "name": "DB1",         "type": "tri_state",-        "description": "Tri-state data output bit 1, valid only when CS and RD are both low, with a logic-0 output of 0.4 V max at 1.6 mA."+        "description": "Tri-state latched data output bit 1, valid when CS and RD are both low."       },       {         "number": "18",         "name": "DB0 (LSB)",         "type": "tri_state",-        "description": "Tri-state data output bit 0 (LSB), valid only when CS and RD are both low, with a logic-0 output of 0.4 V max at 1.6 mA."+        "description": "Tri-state latched data output bit 0 (LSB), valid when CS and RD are both low."       },       {         "number": "19",         "name": "CLK R",         "type": "input",-        "description": "RC timing resistor input for the internal clock generator, where heavy capacitive or DC loading should be avoided (loads under 50 pF are allowed)."+        "description": "RC timing resistor input for the internal clock generator; heavy capacitive or DC loading of this pin should be avoided."       },       {         "number": "20",         "name": "VCC (or VREF)",         "type": "power_in",-        "description": "+5 V supply voltage, also the upper reference input to the ladder, with a recommended range of 4.5 V to 5.5 V and an absolute maximum of 6.5 V."+        "description": "+5 V supply voltage, which also serves as the upper reference input to the ladder."       }     ],     "provenance": {@@ -180,17 +180,18 @@         "consensus": "agreed",         "guards": "pin_guards 0.1: passed",         "guard_notes": [-          "extractor flagged: The datasheet pin table labels DB0 to DB7 as 'O' (output), but the text describes them as tri-state ; The datasheet pin table labels CLK R as 'I' (input), but it is an RC timing pin for the internal clo; The pinout is taken from the page-3 table, which covers both the NFH (PDIP) and DW (SOIC) packages w"+          "extractor flagged: The datasheet pin table labels the DB outputs as 'O' and pin 20 as 'I'; I mapped the DB outputs to t; The datasheet pin table types CLK R as an input, but the text does not give a valid timing resistor "         ],         "pages_sent": 58,-        "cost_usd": 0.1879,-        "at": "2026-11-13T01:56:12"+        "cost_usd": 0.1858,+        "at": "2026-11-17T23:12:44"       },       "datasheet": {         "url": "https://www.ti.com/lit/ds/symlink/adc0804lcwmx.pdf",         "pages": 58,         "sha256": "44bd9e8071ef6612",-        "source_tier": "mfr"+        "source_tier": "mfr",+        "citation": "Texas Instruments datasheet"       },       "cad": "KiCad official (CC-BY-SA 4.0)",       "pins": {@@ -221,7 +222,7 @@         "centre_offset_mm": 0,         "footprint_binding": "identity",         "sha256": "59a10b341e6972b31d81802a048060326da627d8b92dcf4263064f4f62ec808e",-        "checked": "2026-11-13",+        "checked": "2026-11-17",         "checked_by": "factory/step_pose.py (Z-up, origin, seat, binding)"       },       {@@ -239,13 +240,13 @@         "zmin_mm": 0,         "centre_offset_mm": 0,         "footprint_binding": "identity",-        "sha256": "2bd4bfeb9f9d2ce05e515489f8ef859e97685380af1b2379e72e5f6964829ae2",-        "checked": "2026-11-13",+        "sha256": "b876c4187f18011bc5ebe9c2737c57f3db94993ba24dc9528cc377ceec5100ad",+        "checked": "2026-11-17",         "checked_by": "factory/step_pose.py (Z-up, origin, seat, binding)"       }     ],     "package_dims": {-      "package_code": "DW",+      "package_code": "DW0020A",       "source_page": 55,       "D": {         "nom_mm": 12.8,@@ -886,5 +887,7 @@   ],   "visibility": {     "public": true-  }+  },+  "description": "Texas Instruments Pre-ordered Chips, SOIC-20-300mil. Pinout cross-checked by two models against the datasheet, KiCad symbol/footprint/3D.",+  "org": "adom" }\ No newline at end of file