component
AD8361ARMZ
Public Made by Adomby adom
Analog Devices RF Detectors, MSOP-8. Pinout cross-checked by two models against the datasheet, KiCad symbol/footprint/3D.
main
AD8361ARMZ
Analog Devices · RF Detectors · MSOP-8
AD8361ARMZ from Analog Devices, in a MSOP-8. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | VPOS | power_in | Supply voltage pin with an operational range of 2.7 V to 5.5 V. |
| 2 | IREF | input | Output reference control pin; internal reference mode is enabled when it is left open, otherwise it must be tied to VPOS, and it must not be grounded. |
| 3 | RFIN | input | Signal input pin that must be driven from an ac-coupled source, with a low frequency real input impedance of 225 Ω. |
| 4 | PWDN | input | Power-down pin; a logic low below 100 mV enables detector operation, while a logic high above VS − 0.5 V turns the device off. |
| 5 | COMM | power_in | Device ground pin. |
| 6 | FLTR | passive | A capacitor between this pin and VPOS lowers the corner frequency of the modulation filter, whose on-chip filter is 27 pF |
| 7 | VRMS | output | Output pin with near rail-to-rail voltage and limited current drive, with an expected load greater than 10 kΩ to ground. |
| 8 | SREF | input | Supply reference control pin; it must be connected to VPOS to enable supply reference mode, otherwise it should be connected to COMM (ground). |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Analog Devices |
| Package | MSOP-8 |
| Category | Radio Frequency Chip/Antenna |
| Pins | 8 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Operating Range | VS | 2.7 | 5.5 | V | −40°C < TA < +85°C | 3 | |
| Conversion Gain | 6.5 | 8.5 | V/V rms | fRF = 100 MHz, VS = 5 V | 3 | ||
| Output Intercept, Ground Reference Mode | -50 | 150 | mV | fRF = 100 MHz, VS = 5 V | 3 | ||
| Output Intercept, Internal Reference Mode | 300 | 500 | mV | fRF = 100 MHz, VS = 5 V | 3 | ||
| Output Intercept, Supply Reference Mode | 590 | 750 | mV | fRF = 100 MHz, VS = 5 V | 3 | ||
| Power-Down Current, GRM or IRM | 1 | μA | 0 mV rms at RFIN, PWDN Input HI | 3 | |||
| PWDN Bias Current | 1 | μA | 3 | ||||
| Linear Response Range Error (Features) | -0.25 | 0.25 | dB | Linear response up to 2.5 GHz | 1 | ||
| Supply Voltage | VS | 5.5 | V | 4 | |||
| RF Input Level | RFIN | 1 | V rms | 4 | |||
| Equivalent Power | 13 | dBm | re 50 Ω | 4 | |||
| Internal Power Dissipation | 200 | mW | 8-Lead MSOP, free air | 4 | |||
| Maximum Junction Temperature | TJ | 125 | °C | 4 | |||
| Operating Temperature Range | TA | -40 | 85 | °C | 4 | ||
| Storage Temperature Range | TSTG | -65 | 150 | °C | 4 | ||
| Lead Temperature Range | 300 | °C | Soldering 60 sec | 4 | |||
| Thermal Resistance Junction-to-Ambient | θJA | 200 | °C/W | 8-Lead MSOP | 4 | ||
| Thermal Resistance Junction-to-Case | θJC | 44 | °C/W | 8-Lead MSOP | 4 |
CAD (KiCad official)
- Symbol:
AD8361ARMZ - Footprint:
Package_SO:MSOP-8_3x3mm_P0.65mm - 3D model: MSOP-8 (KiCad packages3D, STEP)
- 3D model files:
ad8361armz-etched.step/ad8361armz-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);ad8361armz.step/ad8361armz.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Analog Devices datasheet (22 pp, sha256
00124dab14bd94ad, retrieved 2026-10-30, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).
# AD8361ARMZ
**Analog Devices** · RF Detectors · MSOP-8
AD8361ARMZ from Analog Devices, in a MSOP-8. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
## Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | VPOS | power_in | Supply voltage pin with an operational range of 2.7 V to 5.5 V. |
| 2 | IREF | input | Output reference control pin; internal reference mode is enabled when it is left open, otherwise it must be tied to VPOS, and it must not be grounded. |
| 3 | RFIN | input | Signal input pin that must be driven from an ac-coupled source, with a low frequency real input impedance of 225 Ω. |
| 4 | PWDN | input | Power-down pin; a logic low below 100 mV enables detector operation, while a logic high above VS − 0.5 V turns the device off. |
| 5 | COMM | power_in | Device ground pin. |
| 6 | FLTR | passive | A capacitor between this pin and VPOS lowers the corner frequency of the modulation filter, whose on-chip filter is 27 pF || 2 kΩ for small input signals. |
| 7 | VRMS | output | Output pin with near rail-to-rail voltage and limited current drive, with an expected load greater than 10 kΩ to ground. |
| 8 | SREF | input | Supply reference control pin; it must be connected to VPOS to enable supply reference mode, otherwise it should be connected to COMM (ground). |
## Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Analog Devices |
| Package | MSOP-8 |
| Category | Radio Frequency Chip/Antenna |
| Pins | 8 |
## Electrical characteristics
Limits as printed in the datasheet (page.json `metadata.characteristics` carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Operating Range | VS | 2.7 | | 5.5 | V | −40°C < TA < +85°C | 3 |
| Conversion Gain | | 6.5 | | 8.5 | V/V rms | fRF = 100 MHz, VS = 5 V | 3 |
| Output Intercept, Ground Reference Mode | | -50 | | 150 | mV | fRF = 100 MHz, VS = 5 V | 3 |
| Output Intercept, Internal Reference Mode | | 300 | | 500 | mV | fRF = 100 MHz, VS = 5 V | 3 |
| Output Intercept, Supply Reference Mode | | 590 | | 750 | mV | fRF = 100 MHz, VS = 5 V | 3 |
| Power-Down Current, GRM or IRM | | | | 1 | μA | 0 mV rms at RFIN, PWDN Input HI | 3 |
| PWDN Bias Current | | | | 1 | μA | | 3 |
| Linear Response Range Error (Features) | | -0.25 | | 0.25 | dB | Linear response up to 2.5 GHz | 1 |
| Supply Voltage | VS | | | 5.5 | V | | 4 |
| RF Input Level | RFIN | | | 1 | V rms | | 4 |
| Equivalent Power | | | | 13 | dBm | re 50 Ω | 4 |
| Internal Power Dissipation | | | | 200 | mW | 8-Lead MSOP, free air | 4 |
| Maximum Junction Temperature | TJ | | | 125 | °C | | 4 |
| Operating Temperature Range | TA | -40 | | 85 | °C | | 4 |
| Storage Temperature Range | TSTG | -65 | | 150 | °C | | 4 |
| Lead Temperature Range | | | | 300 | °C | Soldering 60 sec | 4 |
| Thermal Resistance Junction-to-Ambient | θJA | | 200 | | °C/W | 8-Lead MSOP | 4 |
| Thermal Resistance Junction-to-Case | θJC | | 44 | | °C/W | 8-Lead MSOP | 4 |
## CAD (KiCad official)
- Symbol: `AD8361ARMZ`
- Footprint: `Package_SO:MSOP-8_3x3mm_P0.65mm`
- 3D model: MSOP-8 (KiCad packages3D, STEP)
- 3D model files: `ad8361armz-etched.step` / `ad8361armz-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `ad8361armz.step` / `ad8361armz.glb` are the bare package body.
## Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- **Datasheet:** [Analog Devices datasheet](https://www.analog.com/media/en/technical-documentation/data-sheets/AD8361.pdf) (22 pp, sha256 `00124dab14bd94ad`, retrieved 2026-10-30, tier: manufacturer)
- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.3`, primary `claude-haiku-5-5` (text), consensus `claude-sonnet-5-5` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
- **CAD:** KiCad official libraries (CC-BY-SA 4.0).
[Datasheet PDF](docs/ad8361armz-datasheet.pdf)