component
AD7641BSTZ
Public Made by Adomby adom
Analog Devices Pre-ordered Chips, LQFP-48(7x7). Pinout cross-checked by two models against the datasheet, KiCad symbol/footprint/3D.
Generated by kicad-footprint-generator · KiCad file format 20260206
AD7641BSTZ
Analog Devices · Pre-ordered Chips · LQFP-48(7x7)
AD7641BSTZ from Analog Devices, in a LQFP-48(7x7). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model). Symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | AGND | power_in | Analog power ground pin. |
| 2 | AVDD | power_in | Input analog power pin, nominally 2.5 V. |
| 3 | MODE0 | input | Data output interface mode selection bit 0 (with MODE1: 00 = 18-bit, 01 = 16-bit, 10 = 8-bit, 11 = serial interface). |
| 4 | MODE1 | input | Data output interface mode selection bit 1 (with MODE0: 00 = 18-bit, 01 = 16-bit, 10 = 8-bit, 11 = serial interface). |
| 5 | D0/OB/2C | bidirectional | Bit 0 of the parallel output bus when MODE[1:0] = 0; in all other modes selects straight binary (high) or twos complement (low) output coding. |
| 6 | WARP | input | Conversion mode selection: WARP high with NORMAL high selects wideband warp mode, WARP high with NORMAL low selects warp mode (fastest modes, minimum conversion rate required). |
| 7 | NORMAL | input | Conversion mode selection: NORMAL low with WARP low selects normal mode, where full accuracy is maintained independent of the minimum conversion rate. |
| 8 | D1/A0 | bidirectional | Bit 1 of the parallel output bus when MODE[1:0] = 0; in all other modes an input controlling the output data form (Table 7). |
| 9 | D2/A1 | bidirectional | Bit 2 of the parallel output bus when MODE[1:0] = 0; when MODE[1:0] = 1 or 2 an input controlling the output data form (Table 7). |
| 10 | D3 | output | Bit 3 of the parallel output bus in MODE[1:0] = 0, 1 or 2; always an output regardless of interface mode. |
| 11 | D4/DIVSCLK[0] | bidirectional | Bit 4 of the parallel output bus; in serial mode, serial clock division selection input bit 0 (used in serial master read-after-convert mode), otherwise a high-impedance output. |
| 12 | D5/DIVSCLK[1] | bidirectional | Bit 5 of the parallel output bus; in serial mode, serial clock division selection input bit 1 (used in serial master read-after-convert mode), otherwise a high-impedance output. |
| 13 | D6/EXT/INT | bidirectional | Bit 6 of the parallel output bus; in serial mode selects internal (low, master) or external (high, slave) serial data clock. |
| 14 | D7/INVSYNC | bidirectional | Bit 7 of the parallel output bus; in serial master mode selects SYNC active high (low) or active low (high). |
| 15 | D8/INVSCLK | bidirectional | Bit 8 of the parallel output bus; in serial modes inverts the SCLK signal. |
| 16 | D9/RDC/SDIN | bidirectional | Bit 9 of the parallel output bus; in serial master mode RDC selects read during convert (high) or read after convert (low), in serial slave mode SDIN is the daisy-chain data input. |
| 17 | OGND | power_in | Input/output interface digital power ground. |
| 18 | OVDD | power_in | Input/output interface digital power, nominally at the same supply as the host interface (2.5 V or 3 V). |
| 19 | DVDD | power_in | Digital power, nominally 2.5 V. |
| 20 | DGND | power_in | Digital power ground. |
| 21 | D10/SDOUT | output | Bit 10 of the parallel output bus; in serial mode the serial data output, MSB first, synchronized to SCLK. |
| 22 | D11/SCLK | bidirectional | Bit 11 of the parallel output bus; in serial modes the serial data clock input or output depending on EXT/INT. |
| 23 | D12/SYNC | output | Bit 12 of the parallel output bus; in serial master mode the frame synchronization output for the internal data clock. |
| 24 | D13/RDERROR | output | Bit 13 of the parallel output bus; in serial slave mode an incomplete-read error flag pulsed high when a read is not completed before the next conversion completes. |
| 25 | D14 | output | Bit 14 of the parallel output bus; always an output regardless of interface mode. |
| 26 | D15 | output | Bit 15 of the parallel output bus; always an output regardless of interface mode. |
| 27 | D16 | output | Bit 16 of the parallel output bus; always an output regardless of interface mode. |
| 28 | D17 | output | Bit 17 of the parallel output bus; always an output regardless of interface mode. |
| 29 | BUSY | output | Busy output that goes high when a conversion starts and stays high until the conversion completes and data is latched; its falling edge can be used as a data-ready clock. |
| 30 | DGND | power_in | Digital power ground. |
| 31 | RD | input | Read data input; the parallel or serial output bus is enabled when CS and RD are both low. |
| 32 | CS | input | Chip select; with RD low enables the output bus and also gates the external clock in slave serial mode. |
| 33 | RESET | input | Reset input; when high resets the AD7641 and aborts any conversion, falling edge enables calibration mode indicated by BUSY pulsing high; can be tied to DGND if unused. |
| 34 | PD | input | Power-down input; when high powers down the ADC and inhibits conversions after the current one completes. |
| 35 | CNVST | input | Conversion start; a falling edge puts the sample-and-hold into hold and initiates a conversion. |
| 36 | AGND | power_in | Analog power ground pin. |
| 37 | REF | bidirectional | Reference output/input; produces 2.048 V when PDREF/PDBUF are low, or accepts an external reference up to AVDD when they are high; decoupling is required. |
| 38 | REFGND | input | Reference input analog ground. |
| 39 | IN- | input | Differential negative analog input. |
| 40 | NC | unconnected | No connect. |
| 41 | AGND | power_in | Analog power ground pin. |
| 42 | AGND | power_in | Analog power ground pin. |
| 43 | IN+ | input | Differential positive analog input. |
| 44 | AVDD | power_in | Input analog power pin, nominally 2.5 V. |
| 45 | TEMP | output | Temperature sensor analog output. |
| 46 | REFBUFIN | bidirectional | Internal reference output (1.2 V typical band gap, needs external decoupling) or reference buffer input; 1.2 V applied here produces 2.048 V on REF. |
| 47 | PDREF | input | Internal reference power-down input; low enables the internal reference, high powers it down so an external reference must be used. |
| 48 | PDBUF | input | Internal reference buffer power-down input; low enables the buffer (must be low when using the internal reference), high powers it down. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Analog Devices |
| Package | LQFP-48(7x7) |
| Category | Interface ICs |
| Pins | 48 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Operating Input Voltage | VIN+, VIN− | -0.1 | V | VIN+, VIN− to AGND; max is AVDD (external reference) | 3 | ||
| Analog Input CMRR | 58 | dB | fIN = 100 kHz | 3 | |||
| Complete Cycle (warp) | 500 | ns | Wideband warp, warp modes | 3 | |||
| Throughput Rate (warp) | 0.001 | 2 | MSPS | Wideband warp, warp modes | 3 | ||
| Time Between Conversions (warp) | 1 | ms | Wideband warp, warp modes | 3 | |||
| Complete Cycle (normal) | 667 | ns | Normal mode | 3 | |||
| Throughput Rate (normal) | 0 | 1.5 | MSPS | Normal mode | 3 | ||
| Integral Linearity Error | INL | -3 | 2 | 3 | LSB | TMIN to TMAX = −40°C to +70°C (typ printed ±2) | 3 |
| Integral Linearity Error | INL | -3.5 | 2 | 3.5 | LSB | TMIN to TMAX = −40°C to +85°C (typ printed ±2) | 3 |
| No Missing Codes | 18 | Bits | 3 | ||||
| Differential Linearity Error | DNL | -1 | 2 | LSB | 3 | ||
| Zero Error | -15 | 15 | LSB | TMIN to TMAX | 3 | ||
| Gain Error | -0.25 | 0.25 | % of FSR | TMIN to TMAX | 3 | ||
| Internal Reference Output Voltage | REF | 2.038 | 2.048 | 2.058 | V | REF @ 25°C, PDREF = PDBUF = low | 3 |
| REFBUFIN Input Voltage Range | 1.05 | 1.2 | 1.3 | V | PDREF = high, PDBUF = low; REF = 2.048 V typ | 4 | |
| Digital Input Low Voltage | VIL | -0.3 | 0.6 | V | 4 | ||
| Digital Input High Voltage | VIH | 1.7 | 5.25 | V | 4 | ||
| Input Low Current | IIL | -1 | 1 | µA | 4 | ||
| Input High Current | IIH | -1 | 1 | µA | 4 | ||
| Output Low Voltage | VOL | 0.4 | V | ISINK = 500 µA | 4 | ||
| Analog Supply Voltage | AVDD | 2.37 | 2.5 | 2.63 | V | Specified performance | 4 |
| Digital Supply Voltage | DVDD | 2.37 | 2.5 | 2.63 | V | Specified performance | 4 |
| Interface Supply Voltage | OVDD | 2.3 | 3.6 | V | Specified performance | 4 | |
| Power Dissipation, internal reference | 75 | 92 | mW | 2 MSPS throughput, warp mode | 4 | ||
| Power Dissipation, without internal reference | 68 | 85 | mW | 2 MSPS throughput, warp mode | 4 | ||
| Specified Operating Temperature | TMIN to TMAX | -40 | 85 | °C | Specified performance | 4 | |
| Convert Pulse Width | t1 | 15 | 701 | ns | 5 | ||
| Time Between Conversions | t2 | 500 | ns | Warp mode (normal mode 667) | 5 | ||
| CNVST Low to BUSY High Delay | t3 | 23 | ns | 5 | |||
| Conversion Time | t7 | 385 | ns | Warp mode (normal mode 520) | 5 | ||
| Acquisition Time | t8 | 115 | ns | Warp mode/Normal mode | 5 | ||
| RESET Pulse Width | t9 | 15 | ns | 5 | |||
| External SCLK Period | t35 | 12.5 | ns | Slave serial interface | 5 | ||
| Analog Inputs to AGND | -0.3 | V | IN+, IN−, REF, REFBUFIN, TEMP, INGND, REFGND to AGND; upper limit AVDD + 0.3 V | 7 | |||
| Ground Voltage Differences | -0.3 | 0.3 | V | AGND, DGND, OGND | 7 | ||
| AVDD, DVDD Supply Voltage | AVDD, DVDD | -0.3 | 2.7 | V | 7 | ||
| OVDD Supply Voltage | OVDD | -0.3 | 3.8 | V | 7 | ||
| Digital Inputs | -0.3 | 5.5 | V | 7 | |||
| PDREF, PDBUF Input Current | -20 | 20 | mA | 7 | |||
| Internal Power Dissipation | 700 | mW | Device in free air, 48-lead LQFP | 7 | |||
| Junction Temperature | 125 | °C | 7 | ||||
| Storage Temperature Range | -65 | 125 | °C | 7 | |||
| Thermal Resistance Junction to Ambient | θJA | 91 | °C/W | 48-lead LQFP, free air | 7 | ||
| Thermal Resistance Junction to Case | θJC | 30 | °C/W | 48-lead LQFP, free air | 7 | ||
| Resolution | 18 | Bits | 3 | ||||
| Input Current | 18 | µA | 2 MSPS throughput | 3 | |||
| Internal Reference Temperature Drift | 10 | ppm/°C | −40°C to +85°C (printed ±10) | 3 | |||
| Zero Error Temperature Drift | 0.5 | ppm/°C | printed ±0.5 | 3 | |||
| Gain Error Temperature Drift | 1 | ppm/°C | printed ±1 | 3 | |||
| Signal-to-Noise | SNR | 93.5 | dB | fIN = 20 kHz, VREF = 2.5 V | 3 | ||
| Dynamic Range | 95.5 | dB | VREF = 2.5 V | 3 | |||
| Total Harmonic Distortion | THD | -115 | dB | fIN = 20 kHz, VREF = 2.5 V | 3 | ||
| AVDD Operating Current | 23 | mA | 2 MSPS throughput, with internal reference | 4 | |||
| Power-Down Power Dissipation | 2 | µW | PD = high | 4 |
CAD (KiCad official)
- Symbol:
AD7641BSTZ - Footprint:
Package_QFP:LQFP-48_7x7mm_P0.5mm - 3D model: LQFP-48(7x7) (KiCad packages3D, STEP)
- 3D model files:
ad7641bstz-etched.step/ad7641bstz-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);ad7641bstz.step/ad7641bstz.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Analog Devices datasheet (29 pp, sha256
a26016e731416de5, retrieved 2026-11-13, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-sonnet-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).