component
AD7608BSTZ
Public Made by Adomby adom
Analog Devices Analog To Digital Converters (ADCs), LQFP-64(10x10). Pinout cross-checked by two models against the datasheet, KiCad symbol/footprint/3D.
main
Ray
Publish 0.1.0
e7e1bf6
AD7608BSTZ
Analog Devices · Analog To Digital Converters (ADCs) · LQFP-64(10x10)
AD7608BSTZ from Analog Devices, in a LQFP-64(10x10). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model). Symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | AVCC | power_in | Analog supply voltage of 4.75 V to 5.25 V, applied to the front-end amplifiers and ADC core and to be decoupled to AGND. |
| 2 | AGND | power_in | Analog ground reference point for all analog circuitry, which must be connected to the system AGND plane together with the other AGND pins. |
| 3 | OS 0 | input | Oversampling mode control bit OS0 (LSB), which selects the digital filter oversampling ratio per Table 8. |
| 4 | OS 1 | input | Oversampling mode control bit OS1, which selects the digital filter oversampling ratio per Table 8. |
| 5 | OS2 | input | Oversampling mode control bit OS2 (MSB), which selects the digital filter oversampling ratio per Table 8. |
| 6 | PAR/SER SEL | input | Logic low selects the parallel interface and logic high selects the serial interface, in which case DB[15:9] and DB[6:0] must be tied to GND. |
| 7 | STBY | input | Power-down input that places the part in standby mode (all circuitry except the on-chip reference regulators and buffers powered down) or shutdown mode (all circuitry powered down), with the mode selected by the RANGE pin state per Table 7. |
| 8 | RANGE | input | Analog input range select, where logic high sets ±10 V and logic low sets ±5 V for all channels, with changes taking immediate effect and not recommended during a conversion. |
| 9 | CONVST A | input | Conversion start input A, where a low-to-high transition puts the track-and-hold for V1 to V4 (or all channels if shorted to CONVST B) into hold, and separate use with CONVST B is only possible when oversampling is off. |
| 10 | CONVST B | input | Conversion start input B, where a low-to-high transition puts the track-and-hold for V5 to V8 (or all channels if shorted to CONVST A) into hold, and separate use with CONVST A is only possible when oversampling is off. |
| 11 | RESET | input | Active-high reset input whose rising edge resets the AD7608 (typically 100 ns pulse), aborts any conversion in progress, and should be pulsed once after the tWAKE-UP time has elapsed following power-up. |
| 12 | RD/SCLK | input | Parallel read strobe RD (two pulses are needed to read 18 bits per channel) when the parallel interface is selected, or serial clock SCLK when the serial interface is selected. |
| 13 | CS | input | Active-low chip select that frames the data transfer, enabling the parallel output bus when both CS and RD are low or framing the serial read transfer in serial mode. |
| 14 | BUSY | output | Busy output that goes high after both CONVST rising edges and stays high until all channel conversions complete, with its falling edge indicating data is latched and readable after time t4. |
| 15 | FRSTDATA | tri_state | Output that indicates when the V1 result is being read back, three-stated while CS is high and returning low after the third RD falling edge in parallel mode or the 18th SCLK falling edge in serial mode. |
| 16 | DB0 | tri_state | Parallel output pin of the DB[6:0] group, which outputs conversion result bit DB2 during the first RD pulse and 0 during the second RD pulse, and must be tied to GND in serial mode. |
| 17 | DB1 | tri_state | Parallel output pin of the DB[6:0] group, which outputs conversion result bit DB3 during the first RD pulse and 0 during the second RD pulse, and must be tied to GND in serial mode. |
| 18 | DB2 | tri_state | Parallel output pin of the DB[6:0] group, which outputs conversion result bit DB4 during the first RD pulse and 0 during the second RD pulse, and must be tied to GND in serial mode. |
| 19 | DB3 | tri_state | Parallel output pin of the DB[6:0] group, which outputs conversion result bit DB5 during the first RD pulse and 0 during the second RD pulse, and must be tied to GND in serial mode. |
| 20 | DB4 | tri_state | Parallel output pin of the DB[6:0] group, which outputs conversion result bit DB6 during the first RD pulse and 0 during the second RD pulse, and must be tied to GND in serial mode. |
| 21 | DB5 | tri_state | Parallel output pin of the DB[6:0] group, which outputs conversion result bit DB7 during the first RD pulse and 0 during the second RD pulse, and must be tied to GND in serial mode. |
| 22 | DB6 | tri_state | Parallel output pin of the DB[6:0] group, which outputs conversion result bit DB8 during the first RD pulse and 0 during the second RD pulse, and must be tied to GND in serial mode. |
| 23 | VDRIVE | power_in | Logic power supply input of 2.3 V to 5.25 V that sets the interface operating voltage, nominally the same supply as the host DSP or FPGA. |
| 24 | DB7/DOUTA | tri_state | Parallel output bit DB7 (outputs conversion result bit DB9 during the first RD pulse) in parallel mode, or serial data output DOUTA in serial mode. |
| 25 | DB8/DOUTB | tri_state | Parallel output bit DB8 (outputs conversion result bit DB10 during the first RD pulse) in parallel mode, or serial data output DOUTB in serial mode. |
| 26 | AGND | power_in | Analog ground reference point for all analog circuitry, which must be connected to the system AGND plane together with the other AGND pins. |
| 27 | DB9 | tri_state | Parallel output data pin that outputs conversion result bit DB11 during the first RD pulse and zero during the second, and must be tied to GND in serial mode. |
| 28 | DB10 | tri_state | Parallel output data pin that outputs conversion result bit DB12 during the first RD pulse and zero during the second, and must be tied to GND in serial mode. |
| 29 | DB11 | tri_state | Parallel output data pin that outputs conversion result bit DB13 during the first RD pulse and zero during the second, and must be tied to GND in serial mode. |
| 30 | DB12 | tri_state | Parallel output data pin that outputs conversion result bit DB14 during the first RD pulse and zero during the second, and must be tied to GND in serial mode. |
| 31 | DB13 | tri_state | Parallel output data pin that outputs conversion result bit DB15 during the first RD pulse and zero during the second, and must be tied to GND in serial mode. |
| 32 | DB14 | tri_state | Parallel output data bit that outputs conversion result bit DB16 during the first RD pulse and DB0 during the second RD pulse, and must be tied to GND in serial mode. |
| 33 | DB15 | tri_state | Parallel output data bit that outputs conversion result bit DB17 during the first RD pulse and DB1 during the second RD pulse, and must be tied to GND in serial mode. |
| 34 | REF SELECT | input | Logic high enables the internal 2.5 V reference on REFIN/REFOUT, and logic low disables it so an external 2.5 V reference must be applied to REFIN/REFOUT. |
| 35 | AGND | power_in | Analog ground reference point for all analog circuitry, which must be connected to the system AGND plane together with the other AGND pins. |
| 36 | REGCAP | power_out | Output of the internal 2.5 V LDO regulator (2.5 V to 2.7 V), to be decoupled separately to AGND with a 1 µF capacitor. |
| 37 | AVCC | power_in | Analog supply voltage of 4.75 V to 5.25 V, applied to the front-end amplifiers and ADC core and to be decoupled to AGND. |
| 38 | AVCC | power_in | Analog supply voltage of 4.75 V to 5.25 V, applied to the front-end amplifiers and ADC core and to be decoupled to AGND. |
| 39 | REGCAP | power_out | Output of the internal 2.5 V LDO regulator (2.5 V to 2.7 V), to be decoupled separately to AGND with a 1 µF capacitor. |
| 40 | AGND | power_in | Analog ground reference point for all analog circuitry, which must be connected to the system AGND plane together with the other AGND pins. |
| 41 | AGND | power_in | Analog ground reference point for all analog circuitry, which must be connected to the system AGND plane together with the other AGND pins. |
| 42 | REFIN/REFOUT | bidirectional | Reference input/output carrying the 2.5 V on-chip reference when REF SELECT is high or an external 2.5 V reference when REF SELECT is low, requiring a 10 µF decoupling capacitor to ground close to the REFGND pins. |
| 43 | REFGND | power_in | Reference ground pin that should be connected to AGND. |
| 44 | REFCAPA | output | Reference buffer output force/sense pin that must be connected to REFCAPB and decoupled to AGND with a low-ESR 10 µF ceramic capacitor. |
| 45 | REFCAPB | output | Reference buffer output force/sense pin that must be connected to REFCAPA and decoupled to AGND with a low-ESR 10 µF ceramic capacitor. |
| 46 | REFGND | power_in | Reference ground pin that should be connected to AGND. |
| 47 | AGND | power_in | Analog ground reference point for all analog circuitry, which must be connected to the system AGND plane together with the other AGND pins. |
| 48 | AVCC | power_in | Analog supply voltage of 4.75 V to 5.25 V, applied to the front-end amplifiers and ADC core and to be decoupled to AGND. |
| 49 | V1 | input | Single-ended analog input channel 1, with its input range (±10 V or ±5 V) set by the RANGE pin. |
| 50 | V1GND | power_in | Analog input ground for channel V1, which must be connected to the system AGND plane. |
| 51 | V2 | input | Single-ended analog input channel 2, with its input range (±10 V or ±5 V) set by the RANGE pin. |
| 52 | V2GND | power_in | Analog input ground for channel V2, which must be connected to the system AGND plane. |
| 53 | V3 | input | Single-ended analog input channel 3, with its input range (±10 V or ±5 V) set by the RANGE pin. |
| 54 | V3GND | power_in | Analog input ground for channel V3, which must be connected to the system AGND plane. |
| 55 | V4 | input | Single-ended analog input channel 4, with its input range (±10 V or ±5 V) set by the RANGE pin. |
| 56 | V4GND | power_in | Analog input ground for channel V4, which must be connected to the system AGND plane. |
| 57 | V5 | input | Single-ended analog input channel 5, with its input range (±10 V or ±5 V) set by the RANGE pin. |
| 58 | V5GND | power_in | Analog input ground for channel V5, which must be connected to the system AGND plane. |
| 59 | V6 | input | Single-ended analog input channel 6, with its input range (±10 V or ±5 V) set by the RANGE pin. |
| 60 | V6GND | power_in | Analog input ground for channel V6, which must be connected to the system AGND plane. |
| 61 | V7 | input | Single-ended analog input channel 7, with its input range (±10 V or ±5 V) set by the RANGE pin. |
| 62 | V7GND | power_in | Analog input ground for channel V7, which must be connected to the system AGND plane. |
| 63 | V8 | input | Single-ended analog input channel 8, with its input range (±10 V or ±5 V) set by the RANGE pin. |
| 64 | V8GND | power_in | Analog input ground for channel V8, which must be connected to the system AGND plane. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Analog Devices |
| Package | LQFP-64(10x10) |
| Category | Data Converters |
| Pins | 64 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| AVCC analog supply voltage | AVCC | 4.75 | 5.25 | V | 4 | ||
| VDRIVE digital interface supply | VDRIVE | 2.3 | 5.25 | V | 4 | ||
| Signal-to-Noise Ratio (SNR) | SNR | 98 | 99.5 | dB | Oversampling by 16; ±10 V range; fIN = 130 Hz | 4 | |
| Signal-to-Noise Ratio (SNR) | SNR | 95.5 | 97.5 | dB | Oversampling by 16; ±5 V range; fIN = 130 Hz | 4 | |
| Signal-to-Noise Ratio (SNR) | SNR | 89.5 | 90.9 | dB | No oversampling; ±10 V range | 4 | |
| Signal-to-Noise Ratio (SNR) | SNR | 88.5 | 90 | dB | No oversampling; ±5 V range | 4 | |
| Signal-to-(Noise + Distortion) (SINAD) | SINAD | 88.5 | 90.5 | dB | No oversampling; ±10 V range | 4 | |
| Signal-to-(Noise + Distortion) (SINAD) | SINAD | 88 | 89.5 | dB | No oversampling; ±5 V range | 4 | |
| Reference Input Voltage Range | 2.475 | 2.5 | 2.525 | V | 5 | ||
| Reference Output Voltage (REFIN/REFOUT) | 2.49 | 2.505 | V | 5 | |||
| Conversion time (tCONV) | tCONV | 3.45 | 4 | 4.2 | µs | Oversampling off | 6 |
| CONVST x low pulse width | t2 | 25 | ns | Minimum CONVST x low pulse | 6 | ||
| CONVST x high pulse width | t3 | 25 | ns | Minimum CONVST x high pulse | 6 | ||
| Minimum delay RESET low to CONVST x high | t7 | 25 | ns | 6 | |||
| Maximum delay between CONVST A and CONVST B rising edges | t5 | 0.5 | ms | 6 | |||
| Maximum time between last CS rising edge and BUSY falling edge | t6 | 25 | ns | 6 | |||
| AVCC to AGND | AVCC | -0.3 | 7 | V | to AGND | 10 | |
| Analog input voltage to AGND | -16.5 | 16.5 | V | to AGND (footnote 1) | 10 | ||
| VDRIVE to AGND | VDRIVE | -0.3 | V | Upper limit printed as AVCC + 0.3 V; not computed | 10 | ||
| Digital input voltage to AGND | -0.3 | V | Upper limit printed as VDRIVE + 0.3 V; not computed | 10 | |||
| Digital output voltage to AGND | -0.3 | V | Upper limit printed as VDRIVE + 0.3 V; not computed | 10 | |||
| REFIN to AGND | -0.3 | V | Upper limit printed as AVCC + 0.3 V; not computed | 10 | |||
| Input current to any pin except supplies | -10 | 10 | mA | 10 | |||
| Operating temperature range (B version) | -40 | 85 | °C | B version | 10 | ||
| Storage temperature range | -65 | 150 | °C | 10 | |||
| Junction temperature | 150 | °C | 10 | ||||
| Pb/Sn temperature, soldering reflow | 240 | °C | Reflow 10 s to 30 s | 10 | |||
| Pb-free temperature, soldering reflow | 260 | °C | Reflow | 10 | |||
| Total Harmonic Distortion (THD) | THD | -107 | -95 | dB | fIN = 1 kHz sine wave | 4 | |
| Integral Nonlinearity (INL) | INL | 2.5 | 7.5 | LSB | Printed as ±2.5 / ±7.5 LSB; sign not carried | 4 | |
| Positive Full-Scale Error, external reference | 15 | 128 | LSB | External reference | 4 | ||
| Negative Full-Scale Error, external reference | 15 | 128 | LSB | External reference | 4 | ||
| Positive Full-Scale Error Matching | 12 | 95 | LSB | ±10 V range | 4 | ||
| Positive Full-Scale Error Matching | 30 | 128 | LSB | ±5 V range | 4 | ||
| Bipolar Zero Code Error | 3.5 | 24 | LSB | ±10 V range | 4 | ||
| Bipolar Zero Code Error | 3.5 | 48 | LSB | ±5 V range | 4 | ||
| Bipolar Zero Code Error Matching | 3 | 30 | LSB | ±10 V range | 4 | ||
| Bipolar Zero Code Error Matching | 21 | 65 | LSB | ±5 V range | 4 | ||
| Negative Full-Scale Error Matching | 12 | 95 | LSB | ±10 V range | 4 | ||
| Negative Full-Scale Error Matching | 30 | 128 | LSB | ±5 V range | 4 | ||
| ITOTAL Normal Mode (Static) | ITOTAL | 16 | 22 | mA | Digital inputs = 0 V or VDRIVE | 5 | |
| ITOTAL Normal Mode (Operational) | ITOTAL | 20 | 27 | mA | fSAMPLE = 200 kSPS; digital inputs = 0 V or VDRIVE | 5 | |
| ITOTAL Standby Mode | ITOTAL | 5 | 8 | mA | Digital inputs = 0 V or VDRIVE | 5 | |
| ITOTAL Shutdown Mode | ITOTAL | 2 | 11 | µA | Digital inputs = 0 V or VDRIVE | 5 | |
| Power Dissipation Normal Mode (Static) | 80 | 115.5 | mW | 5 | |||
| Power Dissipation Normal Mode (Operational) | 100 | 142 | mW | fSAMPLE = 200 kSPS | 5 | ||
| Power Dissipation Standby Mode | 25 | 42 | mW | 5 | |||
| Power Dissipation Shutdown Mode | 10 | 58 | µW | 5 | |||
| Junction-to-ambient thermal resistance (64-lead LQFP) | θJA | 45 | °C/W | 4-layer board, device soldered in circuit board | 10 | ||
| Junction-to-case thermal resistance (64-lead LQFP) | θJC | 11 | °C/W | 10 |
CAD (KiCad official)
- Symbol:
AD7608BSTZ - Footprint:
Package_QFP:LQFP-64_10x10mm_P0.5mm - 3D model: LQFP-64(10x10) (KiCad packages3D, STEP)
- 3D model files:
ad7608bstz-etched.step/ad7608bstz-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);ad7608bstz.step/ad7608bstz.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Analog Devices datasheet (32 pp, sha256
0cdc1d93209cee21, retrieved 2026-11-13, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).
# AD7608BSTZ
**Analog Devices** · Analog To Digital Converters (ADCs) · LQFP-64(10x10)
AD7608BSTZ from Analog Devices, in a LQFP-64(10x10). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model). Symbol, footprint, and 3D from KiCad-official CAD.
## Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | AVCC | power_in | Analog supply voltage of 4.75 V to 5.25 V, applied to the front-end amplifiers and ADC core and to be decoupled to AGND. |
| 2 | AGND | power_in | Analog ground reference point for all analog circuitry, which must be connected to the system AGND plane together with the other AGND pins. |
| 3 | OS 0 | input | Oversampling mode control bit OS0 (LSB), which selects the digital filter oversampling ratio per Table 8. |
| 4 | OS 1 | input | Oversampling mode control bit OS1, which selects the digital filter oversampling ratio per Table 8. |
| 5 | OS2 | input | Oversampling mode control bit OS2 (MSB), which selects the digital filter oversampling ratio per Table 8. |
| 6 | PAR/SER SEL | input | Logic low selects the parallel interface and logic high selects the serial interface, in which case DB[15:9] and DB[6:0] must be tied to GND. |
| 7 | STBY | input | Power-down input that places the part in standby mode (all circuitry except the on-chip reference regulators and buffers powered down) or shutdown mode (all circuitry powered down), with the mode selected by the RANGE pin state per Table 7. |
| 8 | RANGE | input | Analog input range select, where logic high sets ±10 V and logic low sets ±5 V for all channels, with changes taking immediate effect and not recommended during a conversion. |
| 9 | CONVST A | input | Conversion start input A, where a low-to-high transition puts the track-and-hold for V1 to V4 (or all channels if shorted to CONVST B) into hold, and separate use with CONVST B is only possible when oversampling is off. |
| 10 | CONVST B | input | Conversion start input B, where a low-to-high transition puts the track-and-hold for V5 to V8 (or all channels if shorted to CONVST A) into hold, and separate use with CONVST A is only possible when oversampling is off. |
| 11 | RESET | input | Active-high reset input whose rising edge resets the AD7608 (typically 100 ns pulse), aborts any conversion in progress, and should be pulsed once after the tWAKE-UP time has elapsed following power-up. |
| 12 | RD/SCLK | input | Parallel read strobe RD (two pulses are needed to read 18 bits per channel) when the parallel interface is selected, or serial clock SCLK when the serial interface is selected. |
| 13 | CS | input | Active-low chip select that frames the data transfer, enabling the parallel output bus when both CS and RD are low or framing the serial read transfer in serial mode. |
| 14 | BUSY | output | Busy output that goes high after both CONVST rising edges and stays high until all channel conversions complete, with its falling edge indicating data is latched and readable after time t4. |
| 15 | FRSTDATA | tri_state | Output that indicates when the V1 result is being read back, three-stated while CS is high and returning low after the third RD falling edge in parallel mode or the 18th SCLK falling edge in serial mode. |
| 16 | DB0 | tri_state | Parallel output pin of the DB[6:0] group, which outputs conversion result bit DB2 during the first RD pulse and 0 during the second RD pulse, and must be tied to GND in serial mode. |
| 17 | DB1 | tri_state | Parallel output pin of the DB[6:0] group, which outputs conversion result bit DB3 during the first RD pulse and 0 during the second RD pulse, and must be tied to GND in serial mode. |
| 18 | DB2 | tri_state | Parallel output pin of the DB[6:0] group, which outputs conversion result bit DB4 during the first RD pulse and 0 during the second RD pulse, and must be tied to GND in serial mode. |
| 19 | DB3 | tri_state | Parallel output pin of the DB[6:0] group, which outputs conversion result bit DB5 during the first RD pulse and 0 during the second RD pulse, and must be tied to GND in serial mode. |
| 20 | DB4 | tri_state | Parallel output pin of the DB[6:0] group, which outputs conversion result bit DB6 during the first RD pulse and 0 during the second RD pulse, and must be tied to GND in serial mode. |
| 21 | DB5 | tri_state | Parallel output pin of the DB[6:0] group, which outputs conversion result bit DB7 during the first RD pulse and 0 during the second RD pulse, and must be tied to GND in serial mode. |
| 22 | DB6 | tri_state | Parallel output pin of the DB[6:0] group, which outputs conversion result bit DB8 during the first RD pulse and 0 during the second RD pulse, and must be tied to GND in serial mode. |
| 23 | VDRIVE | power_in | Logic power supply input of 2.3 V to 5.25 V that sets the interface operating voltage, nominally the same supply as the host DSP or FPGA. |
| 24 | DB7/DOUTA | tri_state | Parallel output bit DB7 (outputs conversion result bit DB9 during the first RD pulse) in parallel mode, or serial data output DOUTA in serial mode. |
| 25 | DB8/DOUTB | tri_state | Parallel output bit DB8 (outputs conversion result bit DB10 during the first RD pulse) in parallel mode, or serial data output DOUTB in serial mode. |
| 26 | AGND | power_in | Analog ground reference point for all analog circuitry, which must be connected to the system AGND plane together with the other AGND pins. |
| 27 | DB9 | tri_state | Parallel output data pin that outputs conversion result bit DB11 during the first RD pulse and zero during the second, and must be tied to GND in serial mode. |
| 28 | DB10 | tri_state | Parallel output data pin that outputs conversion result bit DB12 during the first RD pulse and zero during the second, and must be tied to GND in serial mode. |
| 29 | DB11 | tri_state | Parallel output data pin that outputs conversion result bit DB13 during the first RD pulse and zero during the second, and must be tied to GND in serial mode. |
| 30 | DB12 | tri_state | Parallel output data pin that outputs conversion result bit DB14 during the first RD pulse and zero during the second, and must be tied to GND in serial mode. |
| 31 | DB13 | tri_state | Parallel output data pin that outputs conversion result bit DB15 during the first RD pulse and zero during the second, and must be tied to GND in serial mode. |
| 32 | DB14 | tri_state | Parallel output data bit that outputs conversion result bit DB16 during the first RD pulse and DB0 during the second RD pulse, and must be tied to GND in serial mode. |
| 33 | DB15 | tri_state | Parallel output data bit that outputs conversion result bit DB17 during the first RD pulse and DB1 during the second RD pulse, and must be tied to GND in serial mode. |
| 34 | REF SELECT | input | Logic high enables the internal 2.5 V reference on REFIN/REFOUT, and logic low disables it so an external 2.5 V reference must be applied to REFIN/REFOUT. |
| 35 | AGND | power_in | Analog ground reference point for all analog circuitry, which must be connected to the system AGND plane together with the other AGND pins. |
| 36 | REGCAP | power_out | Output of the internal 2.5 V LDO regulator (2.5 V to 2.7 V), to be decoupled separately to AGND with a 1 µF capacitor. |
| 37 | AVCC | power_in | Analog supply voltage of 4.75 V to 5.25 V, applied to the front-end amplifiers and ADC core and to be decoupled to AGND. |
| 38 | AVCC | power_in | Analog supply voltage of 4.75 V to 5.25 V, applied to the front-end amplifiers and ADC core and to be decoupled to AGND. |
| 39 | REGCAP | power_out | Output of the internal 2.5 V LDO regulator (2.5 V to 2.7 V), to be decoupled separately to AGND with a 1 µF capacitor. |
| 40 | AGND | power_in | Analog ground reference point for all analog circuitry, which must be connected to the system AGND plane together with the other AGND pins. |
| 41 | AGND | power_in | Analog ground reference point for all analog circuitry, which must be connected to the system AGND plane together with the other AGND pins. |
| 42 | REFIN/REFOUT | bidirectional | Reference input/output carrying the 2.5 V on-chip reference when REF SELECT is high or an external 2.5 V reference when REF SELECT is low, requiring a 10 µF decoupling capacitor to ground close to the REFGND pins. |
| 43 | REFGND | power_in | Reference ground pin that should be connected to AGND. |
| 44 | REFCAPA | output | Reference buffer output force/sense pin that must be connected to REFCAPB and decoupled to AGND with a low-ESR 10 µF ceramic capacitor. |
| 45 | REFCAPB | output | Reference buffer output force/sense pin that must be connected to REFCAPA and decoupled to AGND with a low-ESR 10 µF ceramic capacitor. |
| 46 | REFGND | power_in | Reference ground pin that should be connected to AGND. |
| 47 | AGND | power_in | Analog ground reference point for all analog circuitry, which must be connected to the system AGND plane together with the other AGND pins. |
| 48 | AVCC | power_in | Analog supply voltage of 4.75 V to 5.25 V, applied to the front-end amplifiers and ADC core and to be decoupled to AGND. |
| 49 | V1 | input | Single-ended analog input channel 1, with its input range (±10 V or ±5 V) set by the RANGE pin. |
| 50 | V1GND | power_in | Analog input ground for channel V1, which must be connected to the system AGND plane. |
| 51 | V2 | input | Single-ended analog input channel 2, with its input range (±10 V or ±5 V) set by the RANGE pin. |
| 52 | V2GND | power_in | Analog input ground for channel V2, which must be connected to the system AGND plane. |
| 53 | V3 | input | Single-ended analog input channel 3, with its input range (±10 V or ±5 V) set by the RANGE pin. |
| 54 | V3GND | power_in | Analog input ground for channel V3, which must be connected to the system AGND plane. |
| 55 | V4 | input | Single-ended analog input channel 4, with its input range (±10 V or ±5 V) set by the RANGE pin. |
| 56 | V4GND | power_in | Analog input ground for channel V4, which must be connected to the system AGND plane. |
| 57 | V5 | input | Single-ended analog input channel 5, with its input range (±10 V or ±5 V) set by the RANGE pin. |
| 58 | V5GND | power_in | Analog input ground for channel V5, which must be connected to the system AGND plane. |
| 59 | V6 | input | Single-ended analog input channel 6, with its input range (±10 V or ±5 V) set by the RANGE pin. |
| 60 | V6GND | power_in | Analog input ground for channel V6, which must be connected to the system AGND plane. |
| 61 | V7 | input | Single-ended analog input channel 7, with its input range (±10 V or ±5 V) set by the RANGE pin. |
| 62 | V7GND | power_in | Analog input ground for channel V7, which must be connected to the system AGND plane. |
| 63 | V8 | input | Single-ended analog input channel 8, with its input range (±10 V or ±5 V) set by the RANGE pin. |
| 64 | V8GND | power_in | Analog input ground for channel V8, which must be connected to the system AGND plane. |
## Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Analog Devices |
| Package | LQFP-64(10x10) |
| Category | Data Converters |
| Pins | 64 |
## Electrical characteristics
Limits as printed in the datasheet (page.json `metadata.characteristics` carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| AVCC analog supply voltage | AVCC | 4.75 | | 5.25 | V | | 4 |
| VDRIVE digital interface supply | VDRIVE | 2.3 | | 5.25 | V | | 4 |
| Signal-to-Noise Ratio (SNR) | SNR | 98 | 99.5 | | dB | Oversampling by 16; ±10 V range; fIN = 130 Hz | 4 |
| Signal-to-Noise Ratio (SNR) | SNR | 95.5 | 97.5 | | dB | Oversampling by 16; ±5 V range; fIN = 130 Hz | 4 |
| Signal-to-Noise Ratio (SNR) | SNR | 89.5 | 90.9 | | dB | No oversampling; ±10 V range | 4 |
| Signal-to-Noise Ratio (SNR) | SNR | 88.5 | 90 | | dB | No oversampling; ±5 V range | 4 |
| Signal-to-(Noise + Distortion) (SINAD) | SINAD | 88.5 | 90.5 | | dB | No oversampling; ±10 V range | 4 |
| Signal-to-(Noise + Distortion) (SINAD) | SINAD | 88 | 89.5 | | dB | No oversampling; ±5 V range | 4 |
| Reference Input Voltage Range | | 2.475 | 2.5 | 2.525 | V | | 5 |
| Reference Output Voltage (REFIN/REFOUT) | | 2.49 | | 2.505 | V | | 5 |
| Conversion time (tCONV) | tCONV | 3.45 | 4 | 4.2 | µs | Oversampling off | 6 |
| CONVST x low pulse width | t2 | 25 | | | ns | Minimum CONVST x low pulse | 6 |
| CONVST x high pulse width | t3 | 25 | | | ns | Minimum CONVST x high pulse | 6 |
| Minimum delay RESET low to CONVST x high | t7 | 25 | | | ns | | 6 |
| Maximum delay between CONVST A and CONVST B rising edges | t5 | | | 0.5 | ms | | 6 |
| Maximum time between last CS rising edge and BUSY falling edge | t6 | | | 25 | ns | | 6 |
| AVCC to AGND | AVCC | -0.3 | | 7 | V | to AGND | 10 |
| Analog input voltage to AGND | | -16.5 | | 16.5 | V | to AGND (footnote 1) | 10 |
| VDRIVE to AGND | VDRIVE | -0.3 | | | V | Upper limit printed as AVCC + 0.3 V; not computed | 10 |
| Digital input voltage to AGND | | -0.3 | | | V | Upper limit printed as VDRIVE + 0.3 V; not computed | 10 |
| Digital output voltage to AGND | | -0.3 | | | V | Upper limit printed as VDRIVE + 0.3 V; not computed | 10 |
| REFIN to AGND | | -0.3 | | | V | Upper limit printed as AVCC + 0.3 V; not computed | 10 |
| Input current to any pin except supplies | | -10 | | 10 | mA | | 10 |
| Operating temperature range (B version) | | -40 | | 85 | °C | B version | 10 |
| Storage temperature range | | -65 | | 150 | °C | | 10 |
| Junction temperature | | | | 150 | °C | | 10 |
| Pb/Sn temperature, soldering reflow | | | | 240 | °C | Reflow 10 s to 30 s | 10 |
| Pb-free temperature, soldering reflow | | | | 260 | °C | Reflow | 10 |
| Total Harmonic Distortion (THD) | THD | | -107 | -95 | dB | fIN = 1 kHz sine wave | 4 |
| Integral Nonlinearity (INL) | INL | | 2.5 | 7.5 | LSB | Printed as ±2.5 / ±7.5 LSB; sign not carried | 4 |
| Positive Full-Scale Error, external reference | | | 15 | 128 | LSB | External reference | 4 |
| Negative Full-Scale Error, external reference | | | 15 | 128 | LSB | External reference | 4 |
| Positive Full-Scale Error Matching | | | 12 | 95 | LSB | ±10 V range | 4 |
| Positive Full-Scale Error Matching | | | 30 | 128 | LSB | ±5 V range | 4 |
| Bipolar Zero Code Error | | | 3.5 | 24 | LSB | ±10 V range | 4 |
| Bipolar Zero Code Error | | | 3.5 | 48 | LSB | ±5 V range | 4 |
| Bipolar Zero Code Error Matching | | | 3 | 30 | LSB | ±10 V range | 4 |
| Bipolar Zero Code Error Matching | | | 21 | 65 | LSB | ±5 V range | 4 |
| Negative Full-Scale Error Matching | | | 12 | 95 | LSB | ±10 V range | 4 |
| Negative Full-Scale Error Matching | | | 30 | 128 | LSB | ±5 V range | 4 |
| ITOTAL Normal Mode (Static) | ITOTAL | | 16 | 22 | mA | Digital inputs = 0 V or VDRIVE | 5 |
| ITOTAL Normal Mode (Operational) | ITOTAL | | 20 | 27 | mA | fSAMPLE = 200 kSPS; digital inputs = 0 V or VDRIVE | 5 |
| ITOTAL Standby Mode | ITOTAL | | 5 | 8 | mA | Digital inputs = 0 V or VDRIVE | 5 |
| ITOTAL Shutdown Mode | ITOTAL | | 2 | 11 | µA | Digital inputs = 0 V or VDRIVE | 5 |
| Power Dissipation Normal Mode (Static) | | | 80 | 115.5 | mW | | 5 |
| Power Dissipation Normal Mode (Operational) | | | 100 | 142 | mW | fSAMPLE = 200 kSPS | 5 |
| Power Dissipation Standby Mode | | | 25 | 42 | mW | | 5 |
| Power Dissipation Shutdown Mode | | | 10 | 58 | µW | | 5 |
| Junction-to-ambient thermal resistance (64-lead LQFP) | θJA | | 45 | | °C/W | 4-layer board, device soldered in circuit board | 10 |
| Junction-to-case thermal resistance (64-lead LQFP) | θJC | | 11 | | °C/W | | 10 |
## CAD (KiCad official)
- Symbol: `AD7608BSTZ`
- Footprint: `Package_QFP:LQFP-64_10x10mm_P0.5mm`
- 3D model: LQFP-64(10x10) (KiCad packages3D, STEP)
- 3D model files: `ad7608bstz-etched.step` / `ad7608bstz-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `ad7608bstz.step` / `ad7608bstz.glb` are the bare package body.
## Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- **Datasheet:** [Analog Devices datasheet](https://www.analog.com/media/en/technical-documentation/data-sheets/AD7608.pdf) (32 pp, sha256 `0cdc1d93209cee21`, retrieved 2026-11-13, tier: manufacturer)
- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.3`, primary `claude-haiku-5-5` (text), consensus `claude-sonnet-5-5` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
- **CAD:** KiCad official libraries (CC-BY-SA 4.0).
[Datasheet PDF](docs/ad7608bstz-datasheet.pdf)