Generated by kicad-footprint-generator · KiCad file format 20260206
AD7477ARTZ-REEL7
Analog Devices · Analog To Digital Converters (ADCs) · SOT-23-6
AD7477ARTZ-REEL7 from Analog Devices, in a SOT-23-6. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model). Symbol and footprint from KiCad-official CAD; the 3D model is generated from the datasheet's package dimensions.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | VDD | power_in | Power supply input; the VDD range for the AD7476/AD7477/AD7478 is from 2.35 V to 5.25 V. |
| 2 | GND | power_in | Analog ground; ground reference point for all circuitry on the part, and all analog input signals should be referred to this GND voltage. |
| 3 | VIN | power_in | Single-ended analog input channel with an input range of 0 V to VDD. |
| 4 | SCLK | input | Serial clock logic input that clocks data out of the part and is also used as the clock source for the conversion process. |
| 5 | SDATA | output | Serial data logic output providing the conversion result MSB first, clocked out on the falling edge of SCLK; the AD7477 stream is four leading zeros, 10 bits of conversion data, then two trailing zeros. |
| 6 | CS | input | Active-low chip select logic input that initiates conversions and frames the serial data transfer. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Analog Devices |
| Package | SOT-23-6 |
| Category | ADC/DAC/Data Conversion |
| Pins | 6 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| VDD to GND | VDD | -0.3 | 7 | V | TA = 25°C | 9 | |
| Analog Input Voltage to GND | VIN | -0.3 | V | -0.3 V to VDD + 0.3 V | 9 | ||
| Digital Input Voltage to GND | -0.3 | 7 | V | 9 | |||
| Digital Output Voltage to GND | -0.3 | V | -0.3 V to VDD + 0.3 V | 9 | |||
| Input Current to Any Pin Except Supplies | -10 | 10 | mA | Transient currents of up to 100 mA do not cause SCR latch-up | 9 | ||
| Operating Temperature Range (A version) | -40 | 85 | °C | Commercial Range (A, B Versions) | 9 | ||
| Storage Temperature Range | -65 | 150 | °C | 9 | |||
| Junction Temperature | 150 | °C | 9 | ||||
| Lead Temperature, Soldering Reflow | 235 | °C | 10 sec to 30 sec; 235 (0/+5)°C | 9 | |||
| Pb-free Temperature Soldering Reflow | 255 | °C | 255 (0/+5)°C | 9 | |||
| ESD | 3.5 | kV | 9 | ||||
| Thermal Impedance θJA | θJA | 230 | °C/W | SOT-23 Package | 9 | ||
| Thermal Impedance θJC | θJC | 92 | °C/W | SOT-23 Package | 9 | ||
| SCLK frequency, min | fSCLK | 10 | kHz | 3 V and 5 V | 8 | ||
| SCLK frequency, max | fSCLK | 20 | MHz | A version, 3 V and 5 V | 8 | ||
| Quiet time between bus relinquish and start of next conversion | tQUIET | 50 | ns | 3 V and 5 V | 8 | ||
| Minimum CS pulsewidth | t1 | 10 | ns | 3 V and 5 V | 8 | ||
| CS to SCLK setup time | t2 | 10 | ns | 3 V and 5 V | 8 | ||
| Delay from CS until SDATA three-state disabled | t3 | 20 | ns | 3 V and 5 V | 8 | ||
| Data access time after SCLK falling edge, 3 V | t4 | 40 | ns | A version, 3 V | 8 | ||
| Data access time after SCLK falling edge, 5 V | t4 | 20 | ns | A version, 5 V | 8 | ||
| SCLK low pulsewidth | t5 | 0.4 | x tSCLK | 3 V and 5 V | 8 | ||
| SCLK high pulsewidth | t6 | 0.4 | x tSCLK | 3 V and 5 V | 8 | ||
| SCLK to data valid hold time | t7 | 10 | ns | 3 V and 5 V | 8 | ||
| SCLK falling edge to SDATA high impedance | t8 | 10 | 25 | ns | 3 V and 5 V | 8 | |
| Power-up time from full power-down | tPOWER-UP | 1 | μs | 3 V and 5 V | 8 |
CAD (land: KiCad; 3D: generated from the datasheet)
- Symbol:
AD7477ARTZ-REEL7 - Footprint:
Package_TO_SOT_SMD:SOT-23-6 - 3D model: SOT-23-6, generated on the KiCad land (body 1.6 x 2.9 mm, terminals on the pads, 1.45 mm tall, datasheet A, max). KiCad's stock model for this land is taller than the datasheet allows, so the model is generated from the datasheet drawing; the dimensions come from the datasheet drawing where it was read and are defaults otherwise (see provenance.model_3d_generated), not the manufacturer's CAD (STEP)
- 3D model files:
ad7477artz-etched.step/ad7477artz-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);ad7477artz.step/ad7477artz.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Analog Devices datasheet (24 pp, sha256
62c2ae6e1d685dec, retrieved 2026-11-16, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-sonnet-5-5(text), consensusclaude-opus-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: land: KiCad official libraries (CC-BY-SA 4.0); 3D: generated from the datasheet's package dimensions (provenance.model_3d_generated).