← Commit history

Initial commit: component/ad5700-1acpz-rl7

Ray ·4c1a5c43c8 ·
2 files changed +308
README.mdadded+62
@@ -0,0 +1,62 @@+# AD5700-1ACPZ-RL7++**Analog Devices** · Interface - Specialized · LFCSP-24(4x4)++AD5700-1ACPZ-RL7 from Analog Devices, in a LFCSP-24(4x4). Pinout and pin descriptions extracted from the manufacturer datasheet by ds2sf; symbol, footprint, and 3D from KiCad-official CAD.++## Pinout++| Pin | Name | Type | Function |+|---|---|---|---|+| 1 | XTAL_EN | input | Active-low digital input to enable external crystal circuit; high level disables crystal for external clock or internal oscillator. |+| 2 | CLKOUT | output | Clock output configurable to 3.6864 MHz, 1.8432 MHz, or 1.2288 MHz based on CLK_CFG pins when crystal or internal oscillator enabled. |+| 3 | CLK_CFG0 | input | Clock configuration control pin used with CLK_CFG1 and XTAL_EN to select clock source per Table 7. |+| 4 | CLK_CFG1 | input | Clock configuration control pin used with CLK_CFG0 and XTAL_EN to select clock source per Table 7. |+| 5 | RESET | input | Active-low digital input places device in power-down mode (16 μA typical); high restores normal operation. |+| 6 | CD | output | Carrier detect digital output; high indicates valid HART carrier signal detected with threshold 85-110 mV p-p. |+| 7 | TXD | input | Transmit data digital input to FSK modulator for 1.2 kHz (mark/1) or 2.2 kHz (space/0) encoding. |+| 8 | RTS | input | Request to send digital input; low enables modulator and disables demodulator; high enables demodulator. |+| 9 | DUPLEX | input | Full-duplex operation enable; high enables simultaneous modulation and demodulation. |+| 10 | RXD | output | Receive data digital output from UART interface with recovered HART data from demodulator. |+| 11 | IOVCC | power_in | Digital interface power supply; voltage range 1.71 V to 5.5 V; decouple with 10 μF and 0.1 μF capacitors to ground. |+| 12 | DGND | power_in | Digital circuit ground reference; connect to AGND for typical operation. |+| 13 | REG_CAP | passive | Capacitor connection to internal voltage regulator; connect 1 μF capacitor to ground. |+| 14 | HART_OUT | output | HART FSK signal output; 459-505 mV p-p with 160 Ω load; DC biased at 0.75 V; AC coupled to external load. |+| 15 | REF | bidirectional | Internal 1.5 V reference output (REF_EN high) or external 2.5 V reference input (REF_EN low, VCC > 2.7 V); 1 μF capacitor to ground. |+| 16 | HART_IN | input | HART FSK input for internal filter mode; AC couple via 2.2 nF series capacitor from HART signal source. |+| 17 | ADC_IP | input | ADC input; connect 680 pF for internal filter or external band-pass filter output for external filter mode. |+| 18 | VCC | power_in | Power supply input; voltage range 2 V to 5.5 V; decouple with 10 μF and 0.1 μF capacitors to ground. |+| 19 | AGND | power_in | Analog circuit ground reference; connect to DGND for typical operation. |+| 20 | XTAL2 | input | External 3.6864 MHz crystal oscillator connection pin; leave open for internal oscillator or external CMOS clock modes. |+| 21 | XTAL1 | input | External 3.6864 MHz crystal connection or external CMOS clock source input; ground for internal oscillator mode. |+| 22 | DGND | power_in | Digital circuit ground reference; connect to AGND for typical operation. |+| 23 | REF_EN | input | Reference enable; high enables internal 1.5 V reference; low requires external 2.5 V reference at REF and VCC > 2.7 V. |+| 24 | FILTER_SEL | input | Filter select; high enables internal filter with signal to HART_IN; low enables external filter with signal to ADC_IP. |+| 25 | EP | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |++## Key specifications++| Parameter | Value |+|---|---|+| Manufacturer | Analog Devices |+| Package | LFCSP-24(4x4) |+| Category | Interface |+| Pins | 25 |++## CAD (KiCad official)++- Symbol: `AD5700-1ACPZ-RL7`+- Footprint: `Package_DFN_QFN:QFN-24-1EP_4x4mm_P0.5mm_EP2.7x2.7mm`+- 3D model: LFCSP-24(4x4) (KiCad packages3D, STEP)+- 3D model files: `ad5700-1acpz-rl7-etched.step` / `ad5700-1acpz-rl7-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `ad5700-1acpz-rl7.step` / `ad5700-1acpz-rl7.glb` are the bare package body.++## Provenance++Data extracted from the manufacturer datasheet, not a distributor listing:++- **Datasheet:** [Analog Devices datasheet](https://jlcpcb.com/api/file/downloadByFileSystemAccessId/8588886807652552704) (24 pp, sha256 `216f1e538d52010b`, retrieved 2026-09-21, tier: lcsc)+- **Datasheet language:** Chinese. Pin names, descriptions, and specs on this page were extracted and translated to English by ds2sf; the linked PDF is the manufacturer original.+- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.2`, primary `claude-haiku-4-5-20251001` (text), consensus `claude-sonnet-4-6` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.+- **CAD:** KiCad official libraries (CC-BY-SA 4.0).++[Datasheet PDF](docs/ad5700-1acpz-rl7-datasheet.pdf)
page.jsonadded+246
@@ -0,0 +1,246 @@+{+  "slug": "ad5700-1acpz-rl7",+  "version": "0.1.0",+  "type": "component",+  "description": "Analog Devices Interface - Specialized, LFCSP-24(4x4). Datasheet-verified pinout, KiCad symbol/footprint/3D.",+  "tags": [+    "component",+    "interface",+    "ad5700-1acpz-rl7",+    "factory-2.0.0",+    "extractor-text"+  ],+  "dependencies": {},+  "hero": {+    "type": "image",+    "path": "docs/hero.png"+  },+  "files": [+    "page.json",+    "README.md",+    "ad5700-1acpz-rl7.kicad_sym",+    "ad5700-1acpz-rl7.kicad_mod",+    "ad5700-1acpz-rl7.glb",+    "ad5700-1acpz-rl7.step",+    "ad5700-1acpz-rl7.lbr",+    "docs/hero.png",+    "docs/ad5700-1acpz-rl7-datasheet.pdf",+    "viewers/symbol.html",+    "viewers/footprint.html"+  ],+  "component": {+    "mpn": "AD5700-1ACPZ-RL7",+    "manufacturer": "Analog Devices",+    "package": "LFCSP-24(4x4)",+    "pin_count": 25,+    "category": "Interface",+    "subcategory": "Interface - Specialized",+    "datasheet": "https://jlcpcb.com/api/file/downloadByFileSystemAccessId/8588886807652552704",+    "parts": {+      "symbol": "ad5700-1acpz-rl7.kicad_sym",+      "footprint": "ad5700-1acpz-rl7.kicad_mod",+      "model_3d": "ad5700-1acpz-rl7-etched.glb",+      "model_3d_plain": "ad5700-1acpz-rl7.glb",+      "model_3d_step": "ad5700-1acpz-rl7-etched.step",+      "model_3d_step_plain": "ad5700-1acpz-rl7.step",+      "lbr": "ad5700-1acpz-rl7.lbr"+    },+    "distributor_links": {+      "lcsc": "C163673"+    },+    "pins": [+      {+        "number": "1",+        "name": "XTAL_EN",+        "type": "input",+        "description": "Active-low digital input to enable external crystal circuit; high level disables crystal for external clock or internal oscillator."+      },+      {+        "number": "2",+        "name": "CLKOUT",+        "type": "output",+        "description": "Clock output configurable to 3.6864 MHz, 1.8432 MHz, or 1.2288 MHz based on CLK_CFG pins when crystal or internal oscillator enabled."+      },+      {+        "number": "3",+        "name": "CLK_CFG0",+        "type": "input",+        "description": "Clock configuration control pin used with CLK_CFG1 and XTAL_EN to select clock source per Table 7."+      },+      {+        "number": "4",+        "name": "CLK_CFG1",+        "type": "input",+        "description": "Clock configuration control pin used with CLK_CFG0 and XTAL_EN to select clock source per Table 7."+      },+      {+        "number": "5",+        "name": "RESET",+        "type": "input",+        "description": "Active-low digital input places device in power-down mode (16 μA typical); high restores normal operation."+      },+      {+        "number": "6",+        "name": "CD",+        "type": "output",+        "description": "Carrier detect digital output; high indicates valid HART carrier signal detected with threshold 85-110 mV p-p."+      },+      {+        "number": "7",+        "name": "TXD",+        "type": "input",+        "description": "Transmit data digital input to FSK modulator for 1.2 kHz (mark/1) or 2.2 kHz (space/0) encoding."+      },+      {+        "number": "8",+        "name": "RTS",+        "type": "input",+        "description": "Request to send digital input; low enables modulator and disables demodulator; high enables demodulator."+      },+      {+        "number": "9",+        "name": "DUPLEX",+        "type": "input",+        "description": "Full-duplex operation enable; high enables simultaneous modulation and demodulation."+      },+      {+        "number": "10",+        "name": "RXD",+        "type": "output",+        "description": "Receive data digital output from UART interface with recovered HART data from demodulator."+      },+      {+        "number": "11",+        "name": "IOVCC",+        "type": "power_in",+        "description": "Digital interface power supply; voltage range 1.71 V to 5.5 V; decouple with 10 μF and 0.1 μF capacitors to ground."+      },+      {+        "number": "12",+        "name": "DGND",+        "type": "power_in",+        "description": "Digital circuit ground reference; connect to AGND for typical operation."+      },+      {+        "number": "13",+        "name": "REG_CAP",+        "type": "passive",+        "description": "Capacitor connection to internal voltage regulator; connect 1 μF capacitor to ground."+      },+      {+        "number": "14",+        "name": "HART_OUT",+        "type": "output",+        "description": "HART FSK signal output; 459-505 mV p-p with 160 Ω load; DC biased at 0.75 V; AC coupled to external load."+      },+      {+        "number": "15",+        "name": "REF",+        "type": "bidirectional",+        "description": "Internal 1.5 V reference output (REF_EN high) or external 2.5 V reference input (REF_EN low, VCC > 2.7 V); 1 μF capacitor to ground."+      },+      {+        "number": "16",+        "name": "HART_IN",+        "type": "input",+        "description": "HART FSK input for internal filter mode; AC couple via 2.2 nF series capacitor from HART signal source."+      },+      {+        "number": "17",+        "name": "ADC_IP",+        "type": "input",+        "description": "ADC input; connect 680 pF for internal filter or external band-pass filter output for external filter mode."+      },+      {+        "number": "18",+        "name": "VCC",+        "type": "power_in",+        "description": "Power supply input; voltage range 2 V to 5.5 V; decouple with 10 μF and 0.1 μF capacitors to ground."+      },+      {+        "number": "19",+        "name": "AGND",+        "type": "power_in",+        "description": "Analog circuit ground reference; connect to DGND for typical operation."+      },+      {+        "number": "20",+        "name": "XTAL2",+        "type": "input",+        "description": "External 3.6864 MHz crystal oscillator connection pin; leave open for internal oscillator or external CMOS clock modes."+      },+      {+        "number": "21",+        "name": "XTAL1",+        "type": "input",+        "description": "External 3.6864 MHz crystal connection or external CMOS clock source input; ground for internal oscillator mode."+      },+      {+        "number": "22",+        "name": "DGND",+        "type": "power_in",+        "description": "Digital circuit ground reference; connect to AGND for typical operation."+      },+      {+        "number": "23",+        "name": "REF_EN",+        "type": "input",+        "description": "Reference enable; high enables internal 1.5 V reference; low requires external 2.5 V reference at REF and VCC > 2.7 V."+      },+      {+        "number": "24",+        "name": "FILTER_SEL",+        "type": "input",+        "description": "Filter select; high enables internal filter with signal to HART_IN; low enables external filter with signal to ADC_IP."+      },+      {+        "number": "25",+        "name": "EP",+        "type": "passive",+        "description": "Exposed pad (from the footprint; not named in the datasheet pin table)."+      }+    ],+    "provenance": {+      "extractor": "extract_pins 0.2",+      "factory_chain": {+        "factory": "2.0.0",+        "extractor": "extract_pins 0.2",+        "primary_model": "claude-haiku-4-5-20251001",+        "primary_mode": "text",+        "consensus_model": "claude-sonnet-4-6",+        "consensus": "agreed",+        "guards": "pin_guards 0.1: passed",+        "guard_notes": [+          "exposed pad 25 added from the footprint",+          "dropped thermal pad ['EP'] absent from footprint"+        ],+        "pages_sent": 24,+        "cost_usd": 0.5073,+        "at": "2026-09-21T23:58:18"+      },+      "datasheet": {+        "url": "https://jlcpcb.com/api/file/downloadByFileSystemAccessId/8588886807652552704",+        "pages": 24,+        "sha256": "216f1e538d52010b",+        "source_tier": "lcsc"+      },+      "cad": "KiCad official (CC-BY-SA 4.0)",+      "pins": {+        "total": 25,+        "described": 25,+        "cites_pages": true,+        "refuses_to_fabricate": true+      }+    },+    "viewers": {+      "symbol": "viewers/symbol.html",+      "footprint": "viewers/footprint.html"+    }+  },+  "visibility": "public",+  "org": "adom",+  "author": {+    "name": "Ray",+    "email": "[email protected]"+  }+}\ No newline at end of file