AD5263BRUZ200 from Analog Devices, in a TSSOP-24. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin	Name	Type	Function
1	B1	passive	Resistor terminal B1 of RDAC channel 1.
2	A1	passive	Resistor terminal A1 (ADDR = 00).
3	W1	passive	Wiper terminal W1.
4	B3	passive	Resistor terminal B3.
5	A3	passive	Resistor terminal A3.
6	W3	passive	Wiper terminal W3 (ADDR = 10).
7	VDD	power_in	Positive power supply, specified for +5 V to +15 V operation.
8	GND	power_in	Ground reference for the device.
9	DIS	input	Digital interface select: SPI when DIS = 0, I2C when DIS = 1.
10	VLOGIC	power_in	Logic supply voltage of 2.7 V to 5.5 V that should always be less than or equal to VDD, with logic levels limited to the logic supply voltage regardless of VDD.
11	SDI/SDA	bidirectional	SDI is the 3-wire serial data input in SPI mode; SDA is the 2-wire serial data input/output in I2C mode.
12	CLK/SCL	input	Serial clock input.
13	CS/AD0	input	Chip select in SPI mode; device address bit 0 in I2C mode.
14	RES/AD1	input	RESET in SPI mode; device address bit 1 in I2C mode.
15	SHDN	input	Shutdown: shorts wiper to terminal B and opens terminal A; tie to +5 V supply if not used and do not tie to VDD if VDD > 5 V.
16	SDO/O1	output	Serial data output in SPI mode (open-drain, requires pull-up resistor); digital output O1 in I2C mode that can drive external logic.
17	NC/O2	output	No connection in SPI mode; digital output O2 in I2C mode that can drive external logic.
18	VSS	power_in	Negative power supply, specified for operation from 0 V to -5 V.
19	W4	passive	Wiper terminal W4 (ADDR = 11).
20	A4	passive	Resistor terminal A4.
21	B4	passive	Resistor terminal B4.
22	W2	passive	Wiper terminal W2 (ADDR = 01).
23	A2	passive	Resistor terminal A2.
24	B2	passive	Resistor terminal B2.

Key specifications

Parameter	Value
Manufacturer	Analog Devices
Package	TSSOP-24
Category	ADC/DAC/Data Conversion
Pins	24

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter	Symbol	Min	Typ	Max	Unit	Conditions	Page
Nominal Resistor Tolerance	∆RAB	-30		30	%	TA = 25°C	3
Input Logic High	VIH	2.4			V		3
Input Logic Low	VIL			0.8	V		3
Input Logic Low (SDA and SCL)	VIL	-0.5			V	VSS = 0 V	3
Wiper Resistance	RW		60	150	Ω	IW = 1 V/RAB	3
Resistor Differential Nonlinearity	R-DNL	-1		1	LSB	RWB, VA = NC	3
Resistor Nonlinearity	R-INL	-1		1	LSB	RWB, VA = NC	3
Differential Nonlinearity	DNL	-1		1	LSB		3
Integral Nonlinearity	INL	-1		1	LSB		3
Full-Scale Error	VWFSE	-2	-1	0	LSB	Code = 0xFF	3
Zero-Scale Error	VWZSE	0	1	2	LSB	Code = 0x00	3
Shutdown Current	ISHDN		0.02	5	µA		3
Common-Mode Leakage	ICM			1	nA	VA = VB = VDD/2	3
Input Current	IIL	-1		1	µA	VIN = 0 V or +5 V	3
SDA Output Logic Low	VOL			0.4	V	ISINK = 3 mA	3
SDA Output Logic Low	VOL			0.6	V	ISINK = 6 mA	3
O1, O2 Output Logic High	VOH	4			V	ISOURCE = 40 µA	3
O1, O2 Output Logic Low	VOL			0.4	V	ISINK = 1.6 mA	3
SDO Output Logic Low	VOL			0.4	V	ISINK = 3 mA	3
Three-State Leakage Current	IOZ	-1		1	µA	VIN = 0 V or +5 V	3
Output Capacitance	COZ		3	8	pF		3
Logic Supply	VL	2.7		5.5	V		4
Power Single-Supply Range	VDD RANGE	4.5		16.5	V	VSS = 0 V	4
Power Dual-Supply Range	VDD/SS RANGE	4.5		7.5	V		4
Logic Supply Current	IL		25	60	µA	VL = +5 V	4
Positive Supply Current	IDD			1	µA	VIH = +5 V or VIL = 0 V	4
Negative Supply Current	ISS			1	µA	VSS = -5 V	4
Power Supply Sensitivity	PSS		0.002	0.01	%/%	∆VDD = +5 V ± 10%	4
Bandwidth (3 dB)	BW		35		kHz	RAB = 200 kΩ	4
VW Settling Time	tS		2		µs	VA = 10 V, VB = 0 V, ±1 LSB error band	4
Nominal End-to-End Resistance	RAB		200		kΩ		2
Resistance Mode Temperature Coefficient	∆RWB/∆T		30		ppm/°C		3
Voltage Divider Temperature Coefficient	∆VW/∆T		5		ppm/°C	Code = 0x80	3
Capacitance Ax, Bx	CA,B		25		pF	f = 1 MHz, measured to GND, Code = 0x80	3
Capacitance Wx	CW		55		pF	f = 1 MHz, measured to GND, Code = 0x80	3
VDD to GND	VDD	-0.3		16.5	V		6
VSS to GND	VSS	-7.5		0	V		6
VDD to VSS	VDD-VSS			16.5	V		6
VL to GND	VL	-0.3		6.5	V		6
Terminal Current Ax to Bx, Ax to Wx, Bx to Wx		-20		20	mA	Pulsed	6
Terminal Current Ax to Bx, Ax to Wx, Bx to Wx		-3		3	mA	Continuous	6
Digital Inputs and Output Voltage to GND		-0.3		7	V		6
Operating Temperature Range	TA	-40		85	°C		6
Maximum Junction Temperature	TJMAX			150	°C		6
Storage Temperature Range		-65		150	°C		6
Reflow Soldering Peak Temperature				260	°C		6
Time at Peak Temperature		20		40	sec		6
Thermal Resistance, Junction-to-Ambient	θJA		143		°C/W	TSSOP-24	6

CAD (KiCad official)

Symbol: AD5263BRUZ200
Footprint: Package_SO:TSSOP-24_4.4x7.8mm_P0.65mm
3D model: TSSOP-24 (KiCad packages3D, STEP)
3D model files: ad5263bruz200-etched.step / ad5263bruz200-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); ad5263bruz200.step / ad5263bruz200.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

Datasheet: Analog Devices datasheet (28 pp, sha256 040f608e737e1152, retrieved 2026-10-30, tier: manufacturer)
Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-haiku-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF

AD5263BRUZ200

Verified AD5263BRUZ200

Verification log 1 record

3D Model

Symbol & Footprint

Schematic Symbol

PCB Footprint

Datasheet

README