main
Ray Publish 0.1.0 f9b4adf

ACS733KLATR-20AB-T

Allegro MicroSystems, LLC · Current Sensors · SOIC-16-300mil

ACS733KLATR-20AB-T from Allegro MicroSystems, LLC, in a SOIC-16-300mil. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 IP+ passive Positive terminal for the current being sensed; fused internally.
2 IP+ passive Positive terminal for the current being sensed; fused internally.
3 IP+ passive Positive terminal for the current being sensed; fused internally.
4 IP+ passive Positive terminal for the current being sensed; fused internally.
5 IP- passive Negative terminal for the current being sensed; fused internally.
6 IP- passive Negative terminal for the current being sensed; fused internally.
7 IP- passive Negative terminal for the current being sensed; fused internally.
8 IP- passive Negative terminal for the current being sensed; fused internally.
9 GND power_in Device ground terminal.
10 GND power_in Device ground terminal.
11 PROGRAM input Programming input for factory calibration; connect to ground for best ESD performance.
12 VIOUT output Analog output signal that changes proportionally with the bidirectional primary sensed current; maximum survivable sink or source current is 15 mA.
13 FAULT output Overcurrent fault output, open drain; requires a pull-up of 10 kΩ to 500 kΩ and sees 0.4 V maximum low output in fault condition with 10 kΩ pull-up.
14 VOC input Sets the overcurrent fault threshold through an external resistor divider on this pin; VOC input range is 0.1 × VCC to 0.4 × VCC.
15 VCC power_in Device power supply terminal; for the ACS733 (3.3 V) variant the supply is 3.14 V to 3.46 V.
16 VCC power_in Device power supply terminal; for the ACS733 (3.3 V) variant the supply is 3.14 V to 3.46 V.

Key specifications

Parameter Value
Manufacturer Allegro MicroSystems, LLC
Package SOIC-16-300mil
Category Sensors
Pins 16

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
Supply Voltage VCC 3.14 3.3 3.46 V 6
Supply Current, ACS733 ICC 20 35 mA ACS733; VCC = 3.3 V 6
Bypass Capacitor CBYPASS 0.1 µF VCC to GND 6
Output Capacitance Load CL 220 pF VIOUT to GND 6
Output Resistive Load RL 50 kΩ VIOUT to GND 6
Output Saturation Voltage VSAT(LOW) VSAT(LOW) 0.2 V VCC = 3.3 V, TA = 25°C, RL(PULLDOWN) = 50 kΩ to VCC 6
Zero Current Output Ratiometry Error ERAT(Q) -12 12 mV TA = 25°C, VCC = ±5 % variation of nominal supply voltage 6
Sensitivity Ratiometry Error ERAT(SENS) -2 2 % TA = 25°C, VCC = ±5 % variation of nominal supply voltage 6
Current Sensing Range IPR -20 20 A 13
Total Output Error ETOT -4.5 4.5 % IP = IPR(max), TA = 25°C 13
Total Output Error ETOT -3 3 % IP = IPR(max), TA = 125°C 13
Total Output Error ETOT -10 10 % IP = IPR(max), TA = -40°C 13
Sensitivity Error ESENS -1.5 1.5 % IP = IPR(max) / 2, TA = 25°C 13
Sensitivity Error ESENS -3 3 % IP = IPR(max) / 2, TA = -40°C 13
Voltage Offset Error VOE -55 55 mV IP = 0 A, TA = 25°C 13
Voltage Offset Error VOE -25 25 mV IP = 0 A, TA = 125°C 13
Voltage Offset Error VOE -120 120 mV IP = 0 A, TA = -40°C 13
Linearity Error ELIN -1 1 % TA = 25°C, up to full-scale IP 13
FAULT Response Time tRESPONSE(F) 0.2 0.5 0.75 µs IP > IFAULT to FAULT pin below VFAULT; input current step 0 to 1.2 × IFAULT 7
FAULT Release Time tC(F) 0.1 0.45 µs 100 pF from FAULT to ground 7
FAULT Output Low Voltage VFAULT 0.4 V In fault condition; RF(PULLUP) = 10 kΩ 7
FAULT Pull-Up Resistance RF(PULLUP) 10 500 kΩ 7
VOC Input Current IVOC 10 100 nA 7
Absolute Maximum Supply Voltage VCC 6 V 3
Absolute Maximum Reverse Supply Voltage VRCC -0.1 V 3
Absolute Maximum Output Voltage VIOUT 6 V 3
Absolute Maximum Reverse Output Voltage VRIOUT -0.1 V 3
Absolute Maximum Fault Output Voltage VFAULT 6 V 3
Absolute Maximum Reverse Fault Output Voltage VRFAULT -0.1 V 3
Absolute Maximum Forward VOC Voltage VVOC 6 V 3
Absolute Maximum Reverse VOC Voltage VVOC -0.1 V 3
Output Current IOUT 15 mA Maximum survivable sink or source current on the output 3
Maximum Continuous Current ICMAX 55 A TA = 25°C 3
Nominal Operating Ambient Temperature TA -40 125 °C Range K 3
Maximum Junction Temperature TJ(max) 165 °C 3
Storage Temperature Tstg -65 170 °C 3
Dielectric Surge Strength Test Voltage VSURGE 10000 V ±5 pulses per IEC 61000-4-5, 1.2 µs rise / 50 µs width 3
Dielectric Strength Test Voltage VISO 3600 VRMS Agency type-tested 60 s per UL 60950-1 (ed. 2) 3
Working Voltage for Basic Isolation VWVBI 616 VRMS Basic isolation per UL 60950-1 (ed. 2) 3
Clearance DCL 7.5 mm Minimum distance through air from IP leads to signal leads 3
Creepage DCR 7.5 mm Minimum distance along package body from IP leads to signal leads 3
Distance Through Insulation DTI 38 µm Minimum internal distance through insulation 3
ESD Human Body Model VHBM -12 12 kV Per AEC-Q100 3
ESD Charged Device Model VCDM -1 1 kV Per AEC-Q100 3
Sensitivity Sens 66 mV/A 13
Primary Conductor Resistance RIP 1 mΩ TA = 25°C 6
Primary Hall Coupling Factor CF(P) 10.8 G/A TA = 25°C 6
Secondary Hall Coupling Factor CF(s) 2.4 G/A TA = 25°C 6
Hall Plate Sensitivity Matching Sensmatch 1 % TA = 25°C 6
Power On Delay Time tPOD 180 µs TA = 25°C 6
Internal Bandwidth BW 1 MHz Small signal -3 dB; CL = 220 pF 6
Rise Time tr 0.7 µs TA = 25°C, CL = 0.22 nF 6
Response Time tRESPONSE 0.2 µs TA = 25°C, CL = 0.22 nF 6
Propagation Delay Time tpd 0.14 µs TA = 25°C, CL = 0.22 nF 6
Output Slew Rate SR 3.2 V/µs TA = 25°C, CL = 0.22 nF 6
Ratiometry Bandwidth BWRAT 10 kHz ±100 mV on VCC 6
Noise Density IND 80 µA/√Hz VCC = 3.3 V, TA = 25°C, CL = 220 pF; input referred 6
Junction-to-Ambient Thermal Resistance RθJA 17 °C/W Mounted on the Allegro ASEK732/3 evaluation board 3
Junction-to-Lead Thermal Resistance RθJL 5 °C/W Mounted on the Allegro ASEK732/3 evaluation board 3

Materials and finish

As the datasheet states them (page.json metadata.appearance; the 3D model's colours follow it).

Part Material Colour / plating Datasheet says Page
contacts tin with 100% matte tin, which is compatible with standard lead (Pb) free printed circuit board assembly processes. Internally, the device 2

CAD (KiCad official)

  • Symbol: ACS733KLATR-20AB-T
  • Footprint: Package_SO:SOIC-16W_7.5x10.3mm_P1.27mm
  • 3D model: SOIC-16-300mil (KiCad packages3D, STEP)
  • 3D model files: acs733klatr-20ab-t-etched.step / acs733klatr-20ab-t-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); acs733klatr-20ab-t.step / acs733klatr-20ab-t.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: Allegro MicroSystems, LLC datasheet (28 pp, sha256 70b2d3947af374f1, retrieved 2026-11-11, tier: lcsc)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-haiku-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF