main
Ray
Publish 0.1.0
4b8e4e6
ACS37002LMCATR-090B5
Allegro MicroSystems, LLC · Current Sensors · SOIC-16-300mil
ACS37002LMCATR-090B5 from Allegro MicroSystems, LLC, in a SOIC-16-300mil. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | IP+ | passive | Terminal for the current being sensed (primary conductor, IP+ pins 1 to 4 are tied together internally and fused internally). |
| 2 | IP+ | passive | Terminal for the current being sensed (primary conductor, IP+ pins 1 to 4 are tied together internally and fused internally). |
| 3 | IP+ | passive | Terminal for the current being sensed (primary conductor, IP+ pins 1 to 4 are tied together internally and fused internally). |
| 4 | IP+ | passive | Terminal for the current being sensed (primary conductor, IP+ pins 1 to 4 are tied together internally and fused internally). |
| 5 | IP- | passive | Terminal for the current being sensed (primary conductor, IP- pins 5 to 8 are tied together internally and fused internally). |
| 6 | IP- | passive | Terminal for the current being sensed (primary conductor, IP- pins 5 to 8 are tied together internally and fused internally). |
| 7 | IP- | passive | Terminal for the current being sensed (primary conductor, IP- pins 5 to 8 are tied together internally and fused internally). |
| 8 | IP- | passive | Terminal for the current being sensed (primary conductor, IP- pins 5 to 8 are tied together internally and fused internally). |
| 9 | OCF | output | Open-drain overcurrent fault output (active low) that needs an external pull-up RPU between 4.7 kΩ and 500 kΩ, with VFAULT-ON of 0.4 V max under fault at RPU = 4.7 kΩ. |
| 10 | VCC | power_in | Device power supply; 5 V devices are rated 4.5 V to 5.5 V and 3.3 V devices 3.15 V to 3.6 V, with 0.1 µF from VCC to GND recommended. |
| 11 | VREF | power_in | Zero-current reference voltage output (2.5 V bidirectional or 0.5 V unidirectional at VCC = 5 V), source/sink limited to ±25 mA, and it may supply VOC. |
| 12 | VIOUT | output | Analog output representing the current flowing through IP; linear operating range is 0.5 V to 4.5 V at 5 V and 0.3 V to 3.0 V at 3.3 V, with 10 kΩ minimum resistive load and 6 nF maximum capacitive load. |
| 13 | VOC | input | Overcurrent fault operation point input; valid range is 0.5 V to 2 V at 5 V (0.33 V to 1.32 V at 3.3 V), and a voltage below 0.1 V selects the internal EEPROM fault level. |
| 14 | GAIN_SEL_1 | input | Gain selection bit 1 (logic input, latched at startup); logic high requires at least 3.75 V at 5 V (2.5 V at 3.3 V) and logic low at most 0.5 V (0.4 V at 3.3 V), with an internal 1 MΩ pull-down to GND. |
| 15 | GND | power_in | Device ground terminal. |
| 16 | GAIN_SEL_0 | input | Gain selection bit 0 (logic input, latched at startup); logic high requires at least 3.75 V at 5 V (2.5 V at 3.3 V) and logic low at most 0.5 V (0.4 V at 3.3 V), with an internal 1 MΩ pull-down to GND. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Allegro MicroSystems, LLC |
| Package | SOIC-16-300mil |
| Category | Sensors |
| Pins | 16 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Supply Voltage (5 V devices) | VCC | 4.5 | 5 | 5.5 | V | 5 V devices only | 7 |
| Supply Current | ICC | 13 | 18 | mA | No load on VIOUT or VREF; VCC = 5 V | 7 | |
| Supply Bypass Capacitor | CBYPASS | 0.1 | µF | VCC to GND recommended | 7 | ||
| Output Resistive Load | RL | 10 | kΩ | VIOUT to GND, VIOUT to VCC | 7 | ||
| Output Capacitive Load | CL | 1 | 6 | nF | VIOUT to GND | 7 | |
| Reference Resistive Load | RVREF | 10 | 62.7 | kΩ | VREF to GND (recommended to supply VOC); VREF to VCC | 7 | |
| Reference Capacitive Load | CVREF | 6 | nF | VREF to GND | 7 | ||
| Fault Pull-Up Resistance | RPU | 4.7 | 500 | kΩ | 7 | ||
| Power-On Reset Voltage (rising) | VPOR(H) | 2.6 | 2.9 | 3.1 | V | VCC rising | 7 |
| Power-On Reset Voltage (falling) | VPOR(L) | 2.2 | 2.5 | 2.8 | V | VCC falling | 7 |
| POR Hysteresis | VPOR(HYS) | 250 | mV | 7 | |||
| Power-On Time | tPOD | 100 | µs | Time from VCC rising ≥ VPOR(H) after a POR event until power-on; VREF, OCF, VIOUT | 7 | ||
| Overvoltage Detection Threshold (rising) | VOVD(H) | 6.1 | 6.4 | 6.8 | V | VCC rising | 7 |
| Overvoltage Detection Threshold (falling) | VOVD(L) | 5.6 | 5.8 | 6.1 | V | VCC falling | 7 |
| Saturation Voltage (low) | VSAT(L) | 0.15 | V | RL = 10 kΩ to VCC | 8 | ||
| Output Voltage Operating Range (5 V linear) | VOOR | 0.5 | 4.5 | V | 5 V linear operating range | 8 | |
| Power Supply Offset Error (bidirectional) | VOE(PS) | -10 | 1 | 10 | mV | Bidirectional; VCC @ VCC(MIN) or VCC(MAX) | 8 |
| Power Supply Sensitivity Error | ESENS(PS) | -1.5 | 0.3 | 1.5 | % | VCC @ VCC(MIN) or VCC(MAX) | 8 |
| Zero Current Reference Voltage | VREF | 2.49 | 2.5 | 2.51 | V | Bidirectional; VCC = 5 V | 9 |
| OCF On Voltage | VFAULT-ON | 0.07 | 0.4 | V | RPU = 4.7 kΩ, under fault condition | 9 | |
| OCF Sink Current (fault asserted) | IOCF(snk) | 0.01 | 1.1 | mA | Fault Asserted | 9 | |
| VOC Operating Voltage Range | VVOC | 0.5 | 2 | V | VCC = 5 V | 9 | |
| Fault Error | EOCF | -10 | 3 | 10 | %IOCF-OP | 9 | |
| OCF Response Time | tOCF | 1 | 1.5 | µs | Time from IOCF-OP, with a 1.2 × IOCF-OP until fault asserts | 9 | |
| OCF Reaction Time | tOCF-R | 0.75 | 1 | µs | Time from IOCF-OP - IOCF(HYS), until fault releases | 9 | |
| Gain Select Logic High Input Voltage | VH(SEL) | 3.75 | V | VCC = 5 V | 9 | ||
| Gain Select Logic Low Input Voltage | VL(SEL) | 0.5 | V | VCC = 5 V | 9 | ||
| Current Sensing Range | IPR | -90 | 90 | A | Gain Sel 00 | 12 | |
| Current Sensing Range | IPR | -108 | 108 | A | Gain Sel 01 | 12 | |
| Current Sensing Range | IPR | -135 | 135 | A | Gain Sel 10 | 12 | |
| Current Sensing Range | IPR | -180 | 180 | A | Gain Sel 11 | 12 | |
| Overcurrent Fault Operating Range | IOCF-OR | 50 | 100 | 200 | %FS | Typ. = factory-programmed default, FS = Full-Scale | 12 |
| Total Error | ETOT | -1.75 | 1.2 | 1.75 | % | IP = IPR(max) | 12 |
| Sensitivity Error | ESENS | -1.5 | 1.1 | 1.5 | % | IP = IPR(max) | 12 |
| Zero Current Reference Error | VRE | -10 | -1 | 10 | mV | VREFactual, VREFideal, IP = 0 A, TA = 25°C to 150°C | 12 |
| Offset Error | VOE | -8 | -1 | 8 | mV | VIOUT(Q), VREF, IP = 0 A, TA = 25°C to 150°C | 12 |
| QVO Error | VQE | -10 | -2 | 10 | mV | VIOUT(Q), IP = 0 A, TA = 25°C to 150°C | 12 |
| Total Error Including Lifetime Drift | ETOT_LTD | -4.2 | -0.8 | 4.2 | % | IP = IPR(max) | 12 |
| Sensitivity Error Including Lifetime Drift | ESENS_LTD | -4 | -1.3 | 4 | % | IP = IPR(max) | 12 |
| Zero Current Reference Error Including Lifetime Drift | VRE_LTD | -10 | -1 | 10 | mV | VREFactual, VREFideal, IP = 0 A, TA = 25°C to 150°C | 12 |
| Offset Error Including Lifetime Drift | VOE_LTD | -10 | -1 | 10 | mV | VIOUT(Q), VREF, IP = 0 A, TA = 25°C to 150°C | 12 |
| Offset Error Including Lifetime Drift | VOE_LTD | -12 | -1 | 12 | mV | VIOUT(Q), VREF, IP = 0 A, TA = -40°C to 25°C | 12 |
| QVO Error Including Lifetime Drift | VQE_LTD | -12 | -2 | 12 | mV | VIOUT(Q), IP = 0 A, TA = 25°C to 150°C | 12 |
| Rise Time | tr | 0.7 | 2.5 | µs | TA = 25°C, CL = 5.7 nF, 10%-90% of 1 V output swing | 8 | |
| Response Time | tRESPONSE | 1.1 | 2.5 | µs | TA = 25°C, CL = 5.7 nF, 90% input to 90% of 1 V output swing | 8 | |
| Forward Supply Voltage | VCC | 6.5 | V | Forward supply voltage | 4 | ||
| Operating Ambient Temperature | TA | -40 | 150 | °C | Operating ambient temperature | 4 | |
| Maximum Junction Temperature | TJ(max) | 165 | °C | 4 | |||
| Primary Conductor Resistance | RIP | 0.27 | mΩ | TA = 25°C | 7 | ||
| Output Buffer Resistance | ROUT | 4 | Ω | Internal output buffer resistance on VIOUT and VREF | 7 | ||
| Sensitivity | Sens | 22.2 | mV/A | Gain Sel 00; IPR(min) < IP < IPR(max) | 12 | ||
| Sensitivity | Sens | 18.5 | mV/A | Gain Sel 01; IPR(min) < IP < IPR(max) | 12 | ||
| Sensitivity | Sens | 14.8 | mV/A | Gain Sel 10; IPR(min) < IP < IPR(max) | 12 | ||
| Sensitivity | Sens | 11.1 | mV/A | Gain Sel 11; IPR(min) < IP < IPR(max) | 12 | ||
| Zero Current Output Voltage | VIOUT(Q) | 2.5 | V | Bidirectional; IP = 0 A, TA = 25°C | 12 |
Materials and finish
As the datasheet states them (page.json metadata.appearance; the 3D model's colours follow it).
| Part | Material | Colour / plating | Datasheet says | Page |
|---|---|---|---|---|
| contacts | tin | Devices are RoHS compliant and lead (Pb) free with 100% matte-tin-plated leadframes. | 1 |
CAD (KiCad official)
- Symbol:
ACS37002LMCATR-090B5 - Footprint:
Package_SO:SOIC-16W_7.5x10.3mm_P1.27mm - 3D model: SOIC-16-300mil (KiCad packages3D, STEP)
- 3D model files:
acs37002lmcatr-090b5-etched.step/acs37002lmcatr-090b5-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);acs37002lmcatr-090b5.step/acs37002lmcatr-090b5.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Allegro MicroSystems, LLC datasheet (32 pp, sha256
0221e9aa81fa89cd, retrieved 2026-11-11, tier: lcsc) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).
# ACS37002LMCATR-090B5
**Allegro MicroSystems, LLC** · Current Sensors · SOIC-16-300mil
ACS37002LMCATR-090B5 from Allegro MicroSystems, LLC, in a SOIC-16-300mil. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
## Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | IP+ | passive | Terminal for the current being sensed (primary conductor, IP+ pins 1 to 4 are tied together internally and fused internally). |
| 2 | IP+ | passive | Terminal for the current being sensed (primary conductor, IP+ pins 1 to 4 are tied together internally and fused internally). |
| 3 | IP+ | passive | Terminal for the current being sensed (primary conductor, IP+ pins 1 to 4 are tied together internally and fused internally). |
| 4 | IP+ | passive | Terminal for the current being sensed (primary conductor, IP+ pins 1 to 4 are tied together internally and fused internally). |
| 5 | IP- | passive | Terminal for the current being sensed (primary conductor, IP- pins 5 to 8 are tied together internally and fused internally). |
| 6 | IP- | passive | Terminal for the current being sensed (primary conductor, IP- pins 5 to 8 are tied together internally and fused internally). |
| 7 | IP- | passive | Terminal for the current being sensed (primary conductor, IP- pins 5 to 8 are tied together internally and fused internally). |
| 8 | IP- | passive | Terminal for the current being sensed (primary conductor, IP- pins 5 to 8 are tied together internally and fused internally). |
| 9 | OCF | output | Open-drain overcurrent fault output (active low) that needs an external pull-up RPU between 4.7 kΩ and 500 kΩ, with VFAULT-ON of 0.4 V max under fault at RPU = 4.7 kΩ. |
| 10 | VCC | power_in | Device power supply; 5 V devices are rated 4.5 V to 5.5 V and 3.3 V devices 3.15 V to 3.6 V, with 0.1 µF from VCC to GND recommended. |
| 11 | VREF | power_in | Zero-current reference voltage output (2.5 V bidirectional or 0.5 V unidirectional at VCC = 5 V), source/sink limited to ±25 mA, and it may supply VOC. |
| 12 | VIOUT | output | Analog output representing the current flowing through IP; linear operating range is 0.5 V to 4.5 V at 5 V and 0.3 V to 3.0 V at 3.3 V, with 10 kΩ minimum resistive load and 6 nF maximum capacitive load. |
| 13 | VOC | input | Overcurrent fault operation point input; valid range is 0.5 V to 2 V at 5 V (0.33 V to 1.32 V at 3.3 V), and a voltage below 0.1 V selects the internal EEPROM fault level. |
| 14 | GAIN_SEL_1 | input | Gain selection bit 1 (logic input, latched at startup); logic high requires at least 3.75 V at 5 V (2.5 V at 3.3 V) and logic low at most 0.5 V (0.4 V at 3.3 V), with an internal 1 MΩ pull-down to GND. |
| 15 | GND | power_in | Device ground terminal. |
| 16 | GAIN_SEL_0 | input | Gain selection bit 0 (logic input, latched at startup); logic high requires at least 3.75 V at 5 V (2.5 V at 3.3 V) and logic low at most 0.5 V (0.4 V at 3.3 V), with an internal 1 MΩ pull-down to GND. |
## Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Allegro MicroSystems, LLC |
| Package | SOIC-16-300mil |
| Category | Sensors |
| Pins | 16 |
## Electrical characteristics
Limits as printed in the datasheet (page.json `metadata.characteristics` carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Supply Voltage (5 V devices) | VCC | 4.5 | 5 | 5.5 | V | 5 V devices only | 7 |
| Supply Current | ICC | | 13 | 18 | mA | No load on VIOUT or VREF; VCC = 5 V | 7 |
| Supply Bypass Capacitor | CBYPASS | 0.1 | | | µF | VCC to GND recommended | 7 |
| Output Resistive Load | RL | 10 | | | kΩ | VIOUT to GND, VIOUT to VCC | 7 |
| Output Capacitive Load | CL | | 1 | 6 | nF | VIOUT to GND | 7 |
| Reference Resistive Load | RVREF | 10 | 62.7 | | kΩ | VREF to GND (recommended to supply VOC); VREF to VCC | 7 |
| Reference Capacitive Load | CVREF | | | 6 | nF | VREF to GND | 7 |
| Fault Pull-Up Resistance | RPU | 4.7 | | 500 | kΩ | | 7 |
| Power-On Reset Voltage (rising) | VPOR(H) | 2.6 | 2.9 | 3.1 | V | VCC rising | 7 |
| Power-On Reset Voltage (falling) | VPOR(L) | 2.2 | 2.5 | 2.8 | V | VCC falling | 7 |
| POR Hysteresis | VPOR(HYS) | 250 | | | mV | | 7 |
| Power-On Time | tPOD | 100 | | | µs | Time from VCC rising ≥ VPOR(H) after a POR event until power-on; VREF, OCF, VIOUT | 7 |
| Overvoltage Detection Threshold (rising) | VOVD(H) | 6.1 | 6.4 | 6.8 | V | VCC rising | 7 |
| Overvoltage Detection Threshold (falling) | VOVD(L) | 5.6 | 5.8 | 6.1 | V | VCC falling | 7 |
| Saturation Voltage (low) | VSAT(L) | | | 0.15 | V | RL = 10 kΩ to VCC | 8 |
| Output Voltage Operating Range (5 V linear) | VOOR | 0.5 | | 4.5 | V | 5 V linear operating range | 8 |
| Power Supply Offset Error (bidirectional) | VOE(PS) | -10 | 1 | 10 | mV | Bidirectional; VCC @ VCC(MIN) or VCC(MAX) | 8 |
| Power Supply Sensitivity Error | ESENS(PS) | -1.5 | 0.3 | 1.5 | % | VCC @ VCC(MIN) or VCC(MAX) | 8 |
| Zero Current Reference Voltage | VREF | 2.49 | 2.5 | 2.51 | V | Bidirectional; VCC = 5 V | 9 |
| OCF On Voltage | VFAULT-ON | | 0.07 | 0.4 | V | RPU = 4.7 kΩ, under fault condition | 9 |
| OCF Sink Current (fault asserted) | IOCF(snk) | 0.01 | | 1.1 | mA | Fault Asserted | 9 |
| VOC Operating Voltage Range | VVOC | 0.5 | | 2 | V | VCC = 5 V | 9 |
| Fault Error | EOCF | -10 | 3 | 10 | %IOCF-OP | | 9 |
| OCF Response Time | tOCF | | 1 | 1.5 | µs | Time from IOCF-OP, with a 1.2 × IOCF-OP until fault asserts | 9 |
| OCF Reaction Time | tOCF-R | | 0.75 | 1 | µs | Time from IOCF-OP - IOCF(HYS), until fault releases | 9 |
| Gain Select Logic High Input Voltage | VH(SEL) | 3.75 | | | V | VCC = 5 V | 9 |
| Gain Select Logic Low Input Voltage | VL(SEL) | | | 0.5 | V | VCC = 5 V | 9 |
| Current Sensing Range | IPR | -90 | | 90 | A | Gain Sel 00 | 12 |
| Current Sensing Range | IPR | -108 | | 108 | A | Gain Sel 01 | 12 |
| Current Sensing Range | IPR | -135 | | 135 | A | Gain Sel 10 | 12 |
| Current Sensing Range | IPR | -180 | | 180 | A | Gain Sel 11 | 12 |
| Overcurrent Fault Operating Range | IOCF-OR | 50 | 100 | 200 | %FS | Typ. = factory-programmed default, FS = Full-Scale | 12 |
| Total Error | ETOT | -1.75 | 1.2 | 1.75 | % | IP = IPR(max) | 12 |
| Sensitivity Error | ESENS | -1.5 | 1.1 | 1.5 | % | IP = IPR(max) | 12 |
| Zero Current Reference Error | VRE | -10 | -1 | 10 | mV | VREFactual, VREFideal, IP = 0 A, TA = 25°C to 150°C | 12 |
| Offset Error | VOE | -8 | -1 | 8 | mV | VIOUT(Q), VREF, IP = 0 A, TA = 25°C to 150°C | 12 |
| QVO Error | VQE | -10 | -2 | 10 | mV | VIOUT(Q), IP = 0 A, TA = 25°C to 150°C | 12 |
| Total Error Including Lifetime Drift | ETOT_LTD | -4.2 | -0.8 | 4.2 | % | IP = IPR(max) | 12 |
| Sensitivity Error Including Lifetime Drift | ESENS_LTD | -4 | -1.3 | 4 | % | IP = IPR(max) | 12 |
| Zero Current Reference Error Including Lifetime Drift | VRE_LTD | -10 | -1 | 10 | mV | VREFactual, VREFideal, IP = 0 A, TA = 25°C to 150°C | 12 |
| Offset Error Including Lifetime Drift | VOE_LTD | -10 | -1 | 10 | mV | VIOUT(Q), VREF, IP = 0 A, TA = 25°C to 150°C | 12 |
| Offset Error Including Lifetime Drift | VOE_LTD | -12 | -1 | 12 | mV | VIOUT(Q), VREF, IP = 0 A, TA = -40°C to 25°C | 12 |
| QVO Error Including Lifetime Drift | VQE_LTD | -12 | -2 | 12 | mV | VIOUT(Q), IP = 0 A, TA = 25°C to 150°C | 12 |
| Rise Time | tr | | 0.7 | 2.5 | µs | TA = 25°C, CL = 5.7 nF, 10%-90% of 1 V output swing | 8 |
| Response Time | tRESPONSE | | 1.1 | 2.5 | µs | TA = 25°C, CL = 5.7 nF, 90% input to 90% of 1 V output swing | 8 |
| Forward Supply Voltage | VCC | | | 6.5 | V | Forward supply voltage | 4 |
| Operating Ambient Temperature | TA | -40 | | 150 | °C | Operating ambient temperature | 4 |
| Maximum Junction Temperature | TJ(max) | | | 165 | °C | | 4 |
| Primary Conductor Resistance | RIP | | 0.27 | | mΩ | TA = 25°C | 7 |
| Output Buffer Resistance | ROUT | | 4 | | Ω | Internal output buffer resistance on VIOUT and VREF | 7 |
| Sensitivity | Sens | | 22.2 | | mV/A | Gain Sel 00; IPR(min) < IP < IPR(max) | 12 |
| Sensitivity | Sens | | 18.5 | | mV/A | Gain Sel 01; IPR(min) < IP < IPR(max) | 12 |
| Sensitivity | Sens | | 14.8 | | mV/A | Gain Sel 10; IPR(min) < IP < IPR(max) | 12 |
| Sensitivity | Sens | | 11.1 | | mV/A | Gain Sel 11; IPR(min) < IP < IPR(max) | 12 |
| Zero Current Output Voltage | VIOUT(Q) | | 2.5 | | V | Bidirectional; IP = 0 A, TA = 25°C | 12 |
## Materials and finish
As the datasheet states them (page.json `metadata.appearance`; the 3D model's colours follow it).
| Part | Material | Colour / plating | Datasheet says | Page |
|---|---|---|---|---|
| contacts | | tin | Devices are RoHS compliant and lead (Pb) free with 100% matte-tin-plated leadframes. | 1 |
## CAD (KiCad official)
- Symbol: `ACS37002LMCATR-090B5`
- Footprint: `Package_SO:SOIC-16W_7.5x10.3mm_P1.27mm`
- 3D model: SOIC-16-300mil (KiCad packages3D, STEP)
- 3D model files: `acs37002lmcatr-090b5-etched.step` / `acs37002lmcatr-090b5-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `acs37002lmcatr-090b5.step` / `acs37002lmcatr-090b5.glb` are the bare package body.
## Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- **Datasheet:** [Allegro MicroSystems, LLC datasheet](docs/acs37002lmcatr-090b5-datasheet.pdf) (32 pp, sha256 `0221e9aa81fa89cd`, retrieved 2026-11-11, tier: lcsc)
- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.3`, primary `claude-haiku-5-5` (text), consensus `claude-sonnet-5-5` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
- **CAD:** KiCad official libraries (CC-BY-SA 4.0).
[Datasheet PDF](docs/acs37002lmcatr-090b5-datasheet.pdf)