component
A5988GJPTR-T
Public Made by Adomby adom
Allegro MicroSystems, LLC Motor Driver ICs, LQFP-48-EP(7x7). Pinout cross-checked by two models against the datasheet, KiCad symbol/footprint/3D.
3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Contents
README
markdownA5988GJPTR-T
Allegro MicroSystems, LLC · Motor Driver ICs · LQFP-48-EP(7x7)
A5988GJPTR-T from Allegro MicroSystems, LLC, in a LQFP-48-EP(7x7). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model). Symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | NC | unconnected | No Connect terminal, listed as not connected in the JP terminal list. |
| 2 | NC | unconnected | No Connect terminal, listed as not connected in the JP terminal list. |
| 3 | OUT1A | output | DMOS Full-Bridge 1 Output A, rated up to 1.6 A and 40 V per bridge output. |
| 4 | SENSE1 | passive | Sense resistor terminal for Bridge 1; SENSEx pin voltage must not exceed the 500 mV maximum. |
| 5 | OUT1B | output | DMOS Full-Bridge 1 Output B, rated up to 1.6 A and 40 V per bridge output. |
| 6 | VBB1 | power_in | Load supply voltage for bridges 1 and 2, operating range 8 to 40 V. |
| 7 | NC | unconnected | No Connect terminal, listed as not connected in the JP terminal list. |
| 8 | OUT2B | output | DMOS Full-Bridge 2 Output B, rated up to 1.6 A and 40 V per bridge output. |
| 9 | SENSE2 | passive | Sense resistor terminal for Bridge 2; SENSEx pin voltage must not exceed the 500 mV maximum. |
| 10 | OUT2A | output | DMOS Full-Bridge 2 Output A, rated up to 1.6 A and 40 V per bridge output. |
| 11 | NC | unconnected | No Connect terminal, listed as not connected in the JP terminal list. |
| 12 | NC | unconnected | No Connect terminal, listed as not connected in the JP terminal list. |
| 13 | PHASE4 | input | Control input for Bridge 4 direction, used with the industry standard I1, I0 and PHASE interface. |
| 14 | PHASE3 | input | Control input for Bridge 3 direction, used with the industry standard I1, I0 and PHASE interface. |
| 15 | SLEEPn | input | Active low sleep mode input; bringing it low puts the device into Sleep Mode and disables the charge pump. |
| 16 | VREF1 | input | Analog input setting the current reference for Bridge 1, input range 0.0 to 1.5 V. |
| 17 | VREF2 | input | Analog input setting the current reference for Bridge 2, input range 0.0 to 1.5 V. |
| 18 | VREF3 | input | Analog input setting the current reference for Bridge 3, input range 0.0 to 1.5 V. |
| 19 | VREF4 | input | Analog input setting the current reference for Bridge 4, input range 0.0 to 1.5 V. |
| 20 | GND | power_in | Analog and digital ground; must be connected together with PGND and the thermal pad externally under the device. |
| 21 | PHASE2 | input | Control input for Bridge 2 direction, used with the industry standard I1, I0 and PHASE interface. |
| 22 | PHASE1 | input | Control input for Bridge 1 direction, used with the industry standard I1, I0 and PHASE interface. |
| 23 | FAULTn | output | Open drain fault output, pulled low when an overcurrent protection event latches the outputs off (JP package only). |
| 24 | I14 | input | Control input I14 for Bridge 4 current step selection, used with the I1, I0 and PHASE interface. |
| 25 | NC | unconnected | No Connect terminal, listed as not connected in the JP terminal list. |
| 26 | NC | unconnected | No Connect terminal, listed as not connected in the JP terminal list. |
| 27 | OUT4A | output | DMOS Full-Bridge 4 Output A, rated up to 1.6 A and 40 V per bridge output. |
| 28 | SENSE4 | passive | Sense resistor terminal for Bridge 4; SENSEx pin voltage must not exceed the 500 mV maximum. |
| 29 | OUT4B | output | DMOS Full-Bridge 4 Output B, rated up to 1.6 A and 40 V per bridge output. |
| 30 | NC | unconnected | No Connect terminal, listed as not connected in the JP terminal list. |
| 31 | VBB2 | power_in | Load supply voltage for bridges 3 and 4, operating range 8 to 40 V. |
| 32 | OUT3B | output | DMOS Full-Bridge 3 Output B, rated up to 1.6 A and 40 V per bridge output. |
| 33 | SENSE3 | passive | Sense resistor terminal for Bridge 3; SENSEx pin voltage must not exceed the 500 mV maximum. |
| 34 | OUT3A | output | DMOS Full-Bridge 3 Output A, rated up to 1.6 A and 40 V per bridge output. |
| 35 | NC | unconnected | No Connect terminal, listed as not connected in the JP terminal list. |
| 36 | NC | unconnected | No Connect terminal, listed as not connected in the JP terminal list. |
| 37 | I13 | input | Control input I13 for Bridge 3 current step selection, used with the I1, I0 and PHASE interface. |
| 38 | I12 | input | Control input I12 for Bridge 2 current step selection, used with the I1, I0 and PHASE interface. |
| 39 | I11 | input | Control input I11 for Bridge 1 current step selection, used with the I1, I0 and PHASE interface. |
| 40 | PGND | power_in | Power ground; must be connected together with GND and the thermal pad externally under the device. |
| 41 | NC | unconnected | No Connect terminal, listed as not connected in the JP terminal list. |
| 42 | VCP | passive | Reservoir capacitor terminal; a 0.1 uF ceramic capacitor is required between VCP and VBBx. |
| 43 | CP1 | passive | Charge pump capacitor terminal; a 0.1 uF ceramic capacitor is connected between CP1 and CP2. |
| 44 | CP2 | passive | Charge pump capacitor terminal; a 0.1 uF ceramic capacitor is connected between CP1 and CP2. |
| 45 | I01 | input | Control input I01 for Bridge 1 current step selection, used with the I1, I0 and PHASE interface. |
| 46 | I02 | input | Control input I02 for Bridge 2 current step selection, used with the I1, I0 and PHASE interface. |
| 47 | I03 | input | Control input I03 for Bridge 3 current step selection, used with the I1, I0 and PHASE interface. |
| 48 | I04 | input | Control input I04 for Bridge 4 current step selection, used with the I1, I0 and PHASE interface. |
| 49 | EP | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Allegro MicroSystems, LLC |
| Package | LQFP-48-EP(7x7) |
| Category | Power Management ICs |
| Pins | 49 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Load Supply Voltage Range | VBB | 8 | 40 | V | Operating | 4 | |
| Source driver on resistance | RDS(on) | 500 | 600 | mΩ | Source driver, IOUT = -1.2 A, TJ = 25°C | 4 | |
| Sink driver on resistance | RDS(on) | 500 | 600 | mΩ | Sink driver, IOUT = 1.2 A, TJ = 25°C | 4 | |
| Output diode forward voltage | Vf | 1.2 | V | IOUT = 1.2 A | 4 | ||
| Output Leakage | IDSS | -20 | 20 | µA | Outputs, VOUT = 0 to VBB | 4 | |
| VBB Supply Current, outputs on | IBB | 23 | mA | IOUT = 0 mA, outputs on, PWM = 50 kHz, DC = 50% | 4 | ||
| VBB Supply Current, outputs off | IBB | 13.7 | 16 | mA | Outputs off | 4 | |
| VBB Supply Current, sleep mode | IBB | -10 | 1 | 10 | µA | Sleep mode (typ printed as <1) | 4 |
| Output Driver Slew Rate | SROUT | 50 | 100 | 150 | ns | 10% to 90% | 4 |
| Logic Input Voltage high | VIN(1) | 2 | V | 4 | |||
| Logic Input Voltage low | VIN(0) | 0.8 | V | 4 | |||
| Logic Input Current | IIN | -20 | 1 | 20 | µA | VIN = 0 to 5 V (typ printed as <1) | 4 |
| Logic Input Hysteresis | Vhys | 150 | 300 | 500 | mV | 4 | |
| Sleep Rising Threshold | 2.5 | 2.7 | 2.95 | V | 4 | ||
| Sleep Falling Threshold | 2.4 | V | 4 | ||||
| Sleep Hysteresis | 250 | 325 | 450 | mV | 4 | ||
| Sleep Input Current | 100 | 150 | µA | 4 | |||
| Crossover Delay | tCOD | 250 | 425 | 1000 | ns | 4 | |
| Blank Time | tBLANK | 0.7 | 1 | 1.3 | µs | 4 | |
| VREFx Pin Input Voltage Range | VREFx | 0 | 1.5 | V | Operating | 4 | |
| VREFx Pin Reference Input Current | IREF | 1 | μA | VREF = 1.5 (printed ±1) | 4 | ||
| Current Trip-Level Error, 100% | VERR | -5 | 5 | % | VREF = 1.5, phase current = 100% | 4 | |
| Current Trip-Level Error, 67% | VERR | -5 | 5 | % | VREF = 1.5, phase current = 67% | 4 | |
| Current Trip-Level Error, 33% | VERR | -15 | 15 | % | VREF = 1.5, phase current = 33% | 4 | |
| VBB UVLO Threshold | VUV(VBB) | 7.3 | 7.6 | 7.9 | V | VBB rising | 4 |
| VBB Hysteresis | VUV(VBB)hys | 400 | 500 | 600 | mV | 4 | |
| Overcurrent Protection Threshold | 1.6 | A | 4 | ||||
| Fault Output Voltage | 0.5 | V | IOUT = 1 mA | 4 | |||
| Fault Output Leakage Current | 1 | µA | No fault, VOUT = 5 V | 4 | |||
| Thermal Shutdown Temperature | TJTSD | 155 | 165 | 175 | °C | 4 | |
| Thermal Shutdown Hysteresis | TJTSDhys | 15 | °C | 4 | |||
| Load Supply Voltage | VBB | -0.5 | 40 | V | 2 | ||
| Output Current | IOUT | 1.6 | A | May be limited by duty cycle, ambient temperature, and heat sinking; do not exceed TJ 150°C | 2 | ||
| Logic Input Voltage Range | VIN | -0.3 | 7 | V | 2 | ||
| SENSEx Pin Voltage | VSENSEx | 0.5 | V | 2 | |||
| SENSEx Pin Voltage, pulsed | VSENSEx | 2.5 | V | Pulsed tw < 1 µs | 2 | ||
| VREFx Pin Voltage | VREFx | 2.5 | V | 2 | |||
| Operating Temperature Range | TA | -40 | 105 | ºC | Range G | 2 | |
| Junction Temperature | TJ(max) | 150 | ºC | 2 | |||
| Storage Temperature Range | Tstg | -40 | 125 | ºC | 2 | ||
| Package Thermal Resistance | RθJA | 23 | ºC/W | JP package, 4-layer PCB based on JEDEC standard | 2 |
Materials and finish
As the datasheet states them (page.json metadata.appearance; the 3D model's colours follow it).
| Part | Material | Colour / plating | Datasheet says | Page |
|---|---|---|---|---|
| contacts | tin | package height of 0.90 mm. The JP is a 7 mm × 7 mm 48-pin LQFP. Both packages are lead (Pb) free, with 100% matte-tin | 1 |
CAD (KiCad official)
- Symbol:
A5988GJPTR-T - Footprint:
Package_QFP:LQFP-48-1EP_7x7mm_P0.5mm_EP3.6x3.6mm - 3D model: LQFP-48-EP(7x7) (KiCad packages3D, STEP)
- 3D model files:
a5988gjptr-t-etched.step/a5988gjptr-t-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);a5988gjptr-t.step/a5988gjptr-t.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Allegro MicroSystems, LLC datasheet (14 pp, sha256
235b3dadc51d1813, retrieved 2026-11-13, tier: lcsc) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).