← Commit history
README.md+29−28
@@ -9,21 +9,21 @@ A4975SLBTR-T from Allegro MicroSystems, LLC, in a SOIC-16-300mil. Pinout and pin | Pin | Name | Type | Function | |---|---|---|---| | 1 | PFD | input | Analog input that sets the current-decay mode: VPFD ≥ 3.5 V selects slow decay, 1.1 V to 3.1 V selects mixed decay, and ≤ 0.8 V selects fast decay. |-| 2 | REF | input | Reference voltage input (operating range 0.5 V to 2.5 V) that, together with RS and the D0 to D2 DAC inputs, sets the peak output current, ITRIP ≈ SRCR × VREF / 5RS. |-| 3 | RC | passive | Timing node where external resistor RT and capacitor CT set the PWM fixed off-time (tOFF ≈ RT·CT, over CT = 470 pF to 1500 pF and RT = 12 kΩ to 100 kΩ) and also set the comparator blanking time. |-| 4 | GROUND | power_in | Return for the logic supply (VCC) and load supply (VBB) and the reference for all voltage measurements; internally fused pin at ground potential. |-| 5 | GROUND | power_in | Return for the logic supply (VCC) and load supply (VBB) and the reference for all voltage measurements; internally fused pin at ground potential. |-| 6 | LOGIC SUPPLY (VCC) | power_in | Logic supply input, operating range 4.5 V to 5.5 V (typically 5 V). |-| 7 | PHASE | input | Logic input that sets the direction of current flow in the load (Table 1), with an internal dead time of about 500 ns to prevent crossover current. |-| 8 | D2 (DATA2) | input | Most significant DAC data input selecting the output current ratio; logic-high requires VIN(1) ≥ 0.55 × VCC and logic-low requires VIN(0) ≤ 0.27 × VCC, and D0 to D2 all low turns off all outputs. |-| 9 | D1 (DATA1) | input | Middle DAC data input selecting the output current ratio; logic-high requires VIN(1) ≥ 0.55 × VCC and logic-low requires VIN(0) ≤ 0.27 × VCC. |-| 10 | OUTA | output | One of two load output connections, rated for continuous output current to ±1.5 A and operating voltages to 50 V. |-| 11 | SENSE | passive | Connection to the sink-transistor emitters where sense resistor RS is connected to ground; the absolute maximum sense voltage is 0.5 V. |-| 12 | GROUND | power_in | Return for the logic supply (VCC) and load supply (VBB) and the reference for all voltage measurements; internally fused pin at ground potential. |-| 13 | GROUND | power_in | Return for the logic supply (VCC) and load supply (VBB) and the reference for all voltage measurements; internally fused pin at ground potential. |-| 14 | D0 (DATA0) | input | Least significant DAC data input selecting the output current ratio; logic-high requires VIN(1) ≥ 0.55 × VCC and logic-low requires VIN(0) ≤ 0.27 × VCC. |-| 15 | OUTB | output | One of two load output connections, rated for continuous output current to ±1.5 A and operating voltages to 50 V. |-| 16 | LOAD SUPPLY (VBB) | power_in | Load supply voltage input, operating range 5 V to 50 V. |+| 2 | REF (VREF) | input | Reference voltage input, operating range 0.5 V to 2.5 V, which together with RS and the D0-D2 inputs sets the peak output current. |+| 3 | RC | passive | Parallel combination of external resistor RT and capacitor CT sets the PWM fixed off-time and also the comparator blanking time; the datasheet's range is CT = 470 pF to 1500 pF and RT = 12 kΩ to 100 kΩ. |+| 4 | GROUND | power_in | Return for the logic supply (VCC) and load supply (VBB) and the reference for all voltage measurements; this internally fused pin is at ground potential. |+| 5 | GROUND | power_in | Return for the logic supply (VCC) and load supply (VBB) and the reference for all voltage measurements; this internally fused pin is at ground potential. |+| 6 | LOGIC SUPPLY (VCC) | power_in | Logic supply voltage, operating range 4.5 V to 5.5 V, typically 5 V. |+| 7 | PHASE | input | Controls the direction of current flow in the load, with an internally generated dead time of approximately 500 ns to prevent crossover current when PHASE switches. |+| 8 | D2 (DATA2) | input | Most significant of the three DAC control bits; logic high requires VCC × 0.55 minimum and logic low requires VCC × 0.27 maximum, and D0-D2 all low disables all outputs. |+| 9 | D1 (DATA1) | input | Middle control bit of the three-bit nonlinear DAC that sets the output current ratio; logic levels are VCC × 0.55 minimum for high and VCC × 0.27 maximum for low. |+| 10 | OUTA | output | One of two full-bridge output load connections, rated for continuous output current of ±1.5 A and an output voltage rating of 50 V. |+| 11 | SENSE | passive | Connection to the sink-transistor emitters; the current-sense resistor RS is connected between this pin and ground. |+| 12 | GROUND | power_in | Return for the logic supply (VCC) and load supply (VBB) and the reference for all voltage measurements; this internally fused pin is at ground potential. |+| 13 | GROUND | power_in | Return for the logic supply (VCC) and load supply (VBB) and the reference for all voltage measurements; this internally fused pin is at ground potential. |+| 14 | D0 (DATA0) | input | Least significant of the three DAC control bits; logic high requires VCC × 0.55 minimum and logic low requires VCC × 0.27 maximum. |+| 15 | OUTB | output | One of two full-bridge output load connections, rated for continuous output current of ±1.5 A and an output voltage rating of 50 V. |+| 16 | LOAD SUPPLY (VBB) | power_in | Supply voltage for the motor load, operating range 5 V to 50 V. |  ## Key specifications @@ -41,20 +41,20 @@ Limits as printed in the datasheet (page.json `metadata.characteristics` carries | Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page | |---|---|---|---|---|---|---|---| | Load Supply Voltage Range | VBB | 5 |  | 50 | V | Operating | 3 |-| Logic Supply Voltage Range | VCC | 4.5 | 5 | 5.5 | V | Operating | 3 |-| Reference Voltage Range | VREF | 0.5 |  | 2.5 | V | Operating | 3 | | Output Leakage Current | ICEX |  |  | 50 | μA | VOUT = VBB | 3 | | Output Leakage Current | ICEX |  |  | -50 | μA | VOUT = 0 V | 3 | | Output Resistance | RDS |  | 1 | 1.4 | Ω | Total Sink + Source, IOUT = 1.5 A, VBB > 8 V, TJ = 25°C | 3 |-| Motor Supply Current (No Load), on | IBB(ON) |  | 500 | 700 | μA | D0 = D1 = D2 = VIN(1) | 3 |-| Motor Supply Current (No Load), off | IBB(OFF) |  | 250 | 500 | μA | D0 = D1 = D2 = VIN(0) | 3 |+| Motor Supply Current (No Load) | IBB(ON) |  | 500 | 700 | μA | D0 = D1 = D2 = VIN(1) | 3 |+| Motor Supply Current (No Load) | IBB(OFF) |  | 250 | 500 | μA | D0 = D1 = D2 = VIN(0) | 3 |+| Logic Supply Voltage Range | VCC | 4.5 | 5 | 5.5 | V | Operating | 3 |+| Reference Voltage Range | VREF | 0.5 |  | 2.5 | V | Operating | 3 | | UVLO Enable Threshold |  | 3.35 | 3.7 | 4.05 | V | VCC = 0 → 5 V | 3 | | UVLO Hysteresis |  | 0.3 | 0.45 | 0.6 | V |  | 3 |-| Logic Input Current, high | IIN(1) |  | 0 | -10 | μA | VIN = VCC = 5 V | 3 |-| Logic Input Current, low | IIN(0) |  | -106 | -200 | μA | VIN = 0 V, VCC = 5 V | 3 |-| Mixed-Decay Comparator Trip Point, slow current-decay mode | VPFD | 3.5 |  |  | V | Slow Current-Decay Mode | 3 |-| Mixed-Decay Comparator Trip Point, mixed current-decay mode | VPFD | 1.1 |  | 3.1 | V | Mixed Current-Decay Mode | 3 |-| Mixed-Decay Comparator Trip Point, fast current-decay mode | VPFD |  |  | 0.8 | V | Fast Current-Decay Mode | 3 |+| Logic Input Current | IIN(1) |  | 0 | -10 | μA | VIN = VCC = 5 V | 3 |+| Logic Input Current | IIN(0) |  | -106 | -200 | μA | VIN = 0 V, VCC = 5 V | 3 |+| Mixed-Decay Comparator Trip Points | VPFD | 3.5 |  |  | V | Slow Current-Decay Mode | 3 |+| Mixed-Decay Comparator Trip Points | VPFD | 1.1 |  | 3.1 | V | Mixed Current-Decay Mode | 3 |+| Mixed-Decay Comparator Trip Points | VPFD |  |  | 0.8 | V | Fast Current-Decay Mode | 3 | | Mixed-Decay Comparator Input Offset Voltage | VIO(PFD) | -50 | 0 | 50 | mV |  | 3 | | Mixed-Decay Comparator Hysteresis | ΔVIO(PFD) | 5 | 25 | 55 | mV |  | 3 | | Reference Input Current | IREF | -5 |  | 5 | μA | VREF = 0.5 to 2.5 V | 3 |@@ -67,11 +67,12 @@ Limits as printed in the datasheet (page.json `metadata.characteristics` carries | Logic Supply Voltage | VCC |  |  | 6 | V |  | 2 | | Logic/Reference Input Voltage Range | VIN | -0.3 |  | 6 | V |  | 2 | | Sense Voltage | VS |  |  | 0.5 | V |  | 2 |-| Output Current, Continuous | IOUT | -1.5 |  | 1.5 | A | Limited by duty cycle, ambient temperature and heat sinking | 2 |-| Operating Ambient Temperature | TA | -20 |  | 85 | ºC | Range S | 2 |+| Output Current, Continuous | IOUT | -1.5 |  | 1.5 | A | Limited by duty cycle, ambient temperature and heat sinking; do not exceed TJ 150 °C | 2 |+| Operating Ambient Temperature, Range S | TA | -20 |  | 85 | ºC |  | 2 | | Maximum Junction Temperature | TJ(max) |  |  | 150 | ºC |  | 2 | | Storage Temperature | Tstg | -55 |  | 150 | ºC |  | 2 |-| Package Thermal Resistance, Junction to Ambient | RθJA |  | 67 |  | ºC/W | LB package, 2-layer PCB, 0.3 in.² 2-oz. exposed copper each side | 2 |+| Package Thermal Resistance, Junction to Ambient | RθJA |  | 67 |  | ºC/W | LB Package, 2-layer PCB, 0.3 in.2 2-oz. exposed copper each side | 2 |+| Package Thermal Resistance, Junction to Tab | RθJT |  | 6 |  | ºC/W |  | 2 |  ## Materials and finish @@ -93,7 +94,7 @@ As the datasheet states them (page.json `metadata.appearance`; the 3D model's co  Data extracted from the manufacturer datasheet, not a distributor listing: -- **Datasheet:** [Allegro MicroSystems, LLC datasheet](docs/a4975slbtr-t-datasheet.pdf) (13 pp, sha256 `a79209451199733e`, retrieved 2026-11-10, tier: lcsc)+- **Datasheet:** [Allegro MicroSystems, LLC datasheet](docs/a4975slbtr-t-datasheet.pdf) (13 pp, sha256 `a79209451199733e`, retrieved 2026-11-11, tier: lcsc) - **Extractor:** parts-factory `2.0.0` / `extract_pins 0.3`, primary `claude-haiku-5-5` (text), consensus `claude-sonnet-5-5` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - **CAD:** KiCad official libraries (CC-BY-SA 4.0). 
a4975slbtr-t-hero.glb
⋯ 1 unchanged line ⋯
a4975slbtr-t-hero.overlay.json+3−3
@@ -74,9 +74,9 @@     "footprint": "a4975slbtr-t.kicad_mod",     "footprint_sha256": "07aa02ced9fcdc61d7c6bb5ea1b86803731041e9e171db91a991c3daa7817383",     "pins": "page.json component.pins",-    "pins_sha256": "06823ad5c7b1ed3c0e7e846389a2a0b57218cba5ddb967d96ac5561731104c49"+    "pins_sha256": "12eb23fc51b4d939e466cdfe090cce523cd4b5349d6f5a450bb4d013520c43a2"   },-  "generator": "adom-wiki 1.8.17 (component_hero)",+  "generator": "adom-wiki 1.8.18 (component_hero)",   "labels": [     {       "pad": "1",@@ -89,7 +89,7 @@     },     {       "pad": "2",-      "text": "REF",+      "text": "REF (VREF)",       "x": -5.825,       "y": -3.175,       "align": "right",
a4975slbtr-t.kicad_sym+1−1
@@ -13,7 +13,7 @@       (number "1" (effects (font (size 1.27 1.27))))     )     (pin input line (at -20.32 5.08 0) (length 5.08)-      (name "REF" (effects (font (size 1.27 1.27))))+      (name "REF (VREF)" (effects (font (size 1.27 1.27))))       (number "2" (effects (font (size 1.27 1.27))))     )     (pin passive line (at -20.32 2.54 0) (length 5.08)
a4975slbtr-t.lbr+2−3
@@ -102,7 +102,7 @@   <text x="0.0000" y="12.7000" size="1.27" layer="95" align="center">&gt;NAME</text>   <text x="0.0000" y="-15.2400" size="1.27" layer="96" align="center">&gt;VALUE</text>   <pin name="PFD" x="-20.32" y="7.62" length="middle" direction="in"/>-  <pin name="REF" x="-20.32" y="5.08" length="middle" direction="in"/>+  <pin name="REF_VREF" x="-20.32" y="5.08" length="middle" direction="in"/>   <pin name="RC" x="-20.32" y="2.54" length="middle" direction="pas"/>   <pin name="GROUND" x="-20.32" y="0" length="middle" direction="pwr"/>   <pin name="GROUND@2" x="-20.32" y="-2.54" length="middle" direction="pwr"/>@@ -129,7 +129,7 @@     <device name="" package="SOIC-16W_7.5x10.3mm_P1.27mm">       <connects>         <connect gate="G$1" pin="PFD" pad="1"/>-        <connect gate="G$1" pin="REF" pad="2"/>+        <connect gate="G$1" pin="REF_VREF" pad="2"/>         <connect gate="G$1" pin="RC" pad="3"/>         <connect gate="G$1" pin="GROUND" pad="4"/>         <connect gate="G$1" pin="GROUND@2" pad="5"/>@@ -152,7 +152,6 @@           <attribute name="DATASHEET" value="https://datasheet.lcsc.com/datasheet/pdf/e7f1b9e2417e49dda6c337bbb6e0b535.pdf" constant="no"/>           <attribute name="ADOM_WIKI" value="https://wiki.adom.inc/adom/a4975slbtr-t" constant="no"/>           <attribute name="MOUSER_PN" value="250-A4975SLBTR-T" constant="no"/>-          <attribute name="DIGIKEY_PN" value="620-1439-2-ND" constant="no"/>           <attribute name="LCSC_PN" value="C27399" constant="no"/>         </technology>       </technologies>
package.json+33−33
@@ -1,6 +1,6 @@ {   "slug": "a4975slbtr-t",-  "version": "0.1.0",+  "version": "0.1.1",   "type": "component",   "description": "Allegro MicroSystems, LLC Motor Driver ICs, SOIC-16-300mil. Pinout cross-checked by two models against the datasheet, KiCad symbol/footprint/3D.",   "tags": [@@ -50,15 +50,15 @@     },     "distributor_links": {       "lcsc": "C27399",+      "digikey": "620-1439-2-ND",       "mouser": "250-A4975SLBTR-T"     },     "distributor_check": {-      "checked_at": "2026-11-10T18:40:14Z",+      "checked_at": "2026-11-11T00:38:39Z",       "source": "Component Ocean /api/assign-pns",       "digikey": {-        "pn": null,-        "status": "deferred",-        "error": "shared DigiKey quota guard: 337 calls left today"+        "pn": "620-1439-2-ND",+        "status": "found"       },       "mouser": {         "pn": "250-A4975SLBTR-T",@@ -74,93 +74,93 @@       },       {         "number": "2",-        "name": "REF",+        "name": "REF (VREF)",         "type": "input",-        "description": "Reference voltage input (operating range 0.5 V to 2.5 V) that, together with RS and the D0 to D2 DAC inputs, sets the peak output current, ITRIP ≈ SRCR × VREF / 5RS."+        "description": "Reference voltage input, operating range 0.5 V to 2.5 V, which together with RS and the D0-D2 inputs sets the peak output current."       },       {         "number": "3",         "name": "RC",         "type": "passive",-        "description": "Timing node where external resistor RT and capacitor CT set the PWM fixed off-time (tOFF ≈ RT·CT, over CT = 470 pF to 1500 pF and RT = 12 kΩ to 100 kΩ) and also set the comparator blanking time."+        "description": "Parallel combination of external resistor RT and capacitor CT sets the PWM fixed off-time and also the comparator blanking time; the datasheet's range is CT = 470 pF to 1500 pF and RT = 12 kΩ to 100 kΩ."       },       {         "number": "4",         "name": "GROUND",         "type": "power_in",-        "description": "Return for the logic supply (VCC) and load supply (VBB) and the reference for all voltage measurements; internally fused pin at ground potential."+        "description": "Return for the logic supply (VCC) and load supply (VBB) and the reference for all voltage measurements; this internally fused pin is at ground potential."       },       {         "number": "5",         "name": "GROUND",         "type": "power_in",-        "description": "Return for the logic supply (VCC) and load supply (VBB) and the reference for all voltage measurements; internally fused pin at ground potential."+        "description": "Return for the logic supply (VCC) and load supply (VBB) and the reference for all voltage measurements; this internally fused pin is at ground potential."       },       {         "number": "6",         "name": "LOGIC SUPPLY (VCC)",         "type": "power_in",-        "description": "Logic supply input, operating range 4.5 V to 5.5 V (typically 5 V)."+        "description": "Logic supply voltage, operating range 4.5 V to 5.5 V, typically 5 V."       },       {         "number": "7",         "name": "PHASE",         "type": "input",-        "description": "Logic input that sets the direction of current flow in the load (Table 1), with an internal dead time of about 500 ns to prevent crossover current."+        "description": "Controls the direction of current flow in the load, with an internally generated dead time of approximately 500 ns to prevent crossover current when PHASE switches."       },       {         "number": "8",         "name": "D2 (DATA2)",         "type": "input",-        "description": "Most significant DAC data input selecting the output current ratio; logic-high requires VIN(1) ≥ 0.55 × VCC and logic-low requires VIN(0) ≤ 0.27 × VCC, and D0 to D2 all low turns off all outputs."+        "description": "Most significant of the three DAC control bits; logic high requires VCC × 0.55 minimum and logic low requires VCC × 0.27 maximum, and D0-D2 all low disables all outputs."       },       {         "number": "9",         "name": "D1 (DATA1)",         "type": "input",-        "description": "Middle DAC data input selecting the output current ratio; logic-high requires VIN(1) ≥ 0.55 × VCC and logic-low requires VIN(0) ≤ 0.27 × VCC."+        "description": "Middle control bit of the three-bit nonlinear DAC that sets the output current ratio; logic levels are VCC × 0.55 minimum for high and VCC × 0.27 maximum for low."       },       {         "number": "10",         "name": "OUTA",         "type": "output",-        "description": "One of two load output connections, rated for continuous output current to ±1.5 A and operating voltages to 50 V."+        "description": "One of two full-bridge output load connections, rated for continuous output current of ±1.5 A and an output voltage rating of 50 V."       },       {         "number": "11",         "name": "SENSE",         "type": "passive",-        "description": "Connection to the sink-transistor emitters where sense resistor RS is connected to ground; the absolute maximum sense voltage is 0.5 V."+        "description": "Connection to the sink-transistor emitters; the current-sense resistor RS is connected between this pin and ground."       },       {         "number": "12",         "name": "GROUND",         "type": "power_in",-        "description": "Return for the logic supply (VCC) and load supply (VBB) and the reference for all voltage measurements; internally fused pin at ground potential."+        "description": "Return for the logic supply (VCC) and load supply (VBB) and the reference for all voltage measurements; this internally fused pin is at ground potential."       },       {         "number": "13",         "name": "GROUND",         "type": "power_in",-        "description": "Return for the logic supply (VCC) and load supply (VBB) and the reference for all voltage measurements; internally fused pin at ground potential."+        "description": "Return for the logic supply (VCC) and load supply (VBB) and the reference for all voltage measurements; this internally fused pin is at ground potential."       },       {         "number": "14",         "name": "D0 (DATA0)",         "type": "input",-        "description": "Least significant DAC data input selecting the output current ratio; logic-high requires VIN(1) ≥ 0.55 × VCC and logic-low requires VIN(0) ≤ 0.27 × VCC."+        "description": "Least significant of the three DAC control bits; logic high requires VCC × 0.55 minimum and logic low requires VCC × 0.27 maximum."       },       {         "number": "15",         "name": "OUTB",         "type": "output",-        "description": "One of two load output connections, rated for continuous output current to ±1.5 A and operating voltages to 50 V."+        "description": "One of two full-bridge output load connections, rated for continuous output current of ±1.5 A and an output voltage rating of 50 V."       },       {         "number": "16",         "name": "LOAD SUPPLY (VBB)",         "type": "power_in",-        "description": "Load supply voltage input, operating range 5 V to 50 V."+        "description": "Supply voltage for the motor load, operating range 5 V to 50 V."       }     ],     "provenance": {@@ -174,11 +174,11 @@         "consensus": "agreed",         "guards": "pin_guards 0.1: passed",         "guard_notes": [-          "extractor flagged: Pin numbers and names were taken from the Terminal Functions table on page 5, which the datasheet sa; Pins 4, 5, 12 and 13 are marked as internally fused in the LB package drawing (page 12). They are li; The ERC types for RC (pin 3) and SENSE (pin 11) are not stated in the datasheet. They are classified"+          "extractor flagged: The page 9 pin-diagram text is scrambled, so pin assignments were taken from the Terminal Functions ; Pin types for PFD, REF, RC, SENSE and the bridge outputs are inferred from their functions in the da"         ],         "pages_sent": 13,-        "cost_usd": 0.0748,-        "at": "2026-11-10T18:40:06"+        "cost_usd": 0.0725,+        "at": "2026-11-11T00:38:24"       },       "datasheet": {         "url": "https://datasheet.lcsc.com/datasheet/pdf/e7f1b9e2417e49dda6c337bbb6e0b535.pdf",@@ -215,7 +215,7 @@         "centre_offset_mm": 0.0,         "footprint_binding": "identity",         "sha256": "159663ceb2b4996b1b89d3111e4a355fc27de3e24d3570f50e5ed9086e0d73af",-        "checked": "2026-11-10",+        "checked": "2026-11-11",         "checked_by": "factory/step_pose.py (Z-up, origin, seat, binding)"       },       {@@ -233,8 +233,8 @@         "zmin_mm": -0.0,         "centre_offset_mm": 0.0,         "footprint_binding": "identity",-        "sha256": "cec4a54e1c302a0631fc22fa775fe87cfea111274b23382463723c250059f829",-        "checked": "2026-11-10",+        "sha256": "aa78a388270ed8f0096bc3990660e0b4aac736147ea7447a0a9deeaccb23d615",+        "checked": "2026-11-11",         "checked_by": "factory/step_pose.py (Z-up, origin, seat, binding)"       }     ],@@ -244,22 +244,22 @@       "D": {         "nom_mm": 10.3,         "range_mm": [-          null,-          null+          10.1,+          10.5         ]       },       "E1": {         "nom_mm": 7.5,         "range_mm": [-          null,-          null+          7.4,+          7.6         ]       },       "E": {         "nom_mm": 10.3,         "range_mm": [-          null,-          null+          9.97,+          10.63         ]       },       "e": {
page.json+36−34
@@ -4,7 +4,7 @@   "slug": "a4975slbtr-t",   "title": "A4975SLBTR-T",   "brief": "Allegro MicroSystems, LLC Motor Driver ICs, SOIC-16-300mil. Pinout cross-checked by two models against the datasheet, KiCad symbol/footprint/3D.",-  "version": "0.1.0",+  "version": "0.1.1",   "license": "CC-BY-SA-4.0",   "tags": [     "component",@@ -32,15 +32,15 @@     },     "distributor_links": {       "lcsc": "C27399",+      "digikey": "620-1439-2-ND",       "mouser": "250-A4975SLBTR-T"     },     "distributor_check": {-      "checked_at": "2026-11-10T18:40:14Z",+      "checked_at": "2026-11-11T00:38:39Z",       "source": "Component Ocean /api/assign-pns",       "digikey": {-        "pn": null,-        "status": "deferred",-        "error": "shared DigiKey quota guard: 337 calls left today"+        "pn": "620-1439-2-ND",+        "status": "found"       },       "mouser": {         "pn": "250-A4975SLBTR-T",@@ -56,93 +56,93 @@       },       {         "number": "2",-        "name": "REF",+        "name": "REF (VREF)",         "type": "input",-        "description": "Reference voltage input (operating range 0.5 V to 2.5 V) that, together with RS and the D0 to D2 DAC inputs, sets the peak output current, ITRIP ≈ SRCR × VREF / 5RS."+        "description": "Reference voltage input, operating range 0.5 V to 2.5 V, which together with RS and the D0-D2 inputs sets the peak output current."       },       {         "number": "3",         "name": "RC",         "type": "passive",-        "description": "Timing node where external resistor RT and capacitor CT set the PWM fixed off-time (tOFF ≈ RT·CT, over CT = 470 pF to 1500 pF and RT = 12 kΩ to 100 kΩ) and also set the comparator blanking time."+        "description": "Parallel combination of external resistor RT and capacitor CT sets the PWM fixed off-time and also the comparator blanking time; the datasheet's range is CT = 470 pF to 1500 pF and RT = 12 kΩ to 100 kΩ."       },       {         "number": "4",         "name": "GROUND",         "type": "power_in",-        "description": "Return for the logic supply (VCC) and load supply (VBB) and the reference for all voltage measurements; internally fused pin at ground potential."+        "description": "Return for the logic supply (VCC) and load supply (VBB) and the reference for all voltage measurements; this internally fused pin is at ground potential."       },       {         "number": "5",         "name": "GROUND",         "type": "power_in",-        "description": "Return for the logic supply (VCC) and load supply (VBB) and the reference for all voltage measurements; internally fused pin at ground potential."+        "description": "Return for the logic supply (VCC) and load supply (VBB) and the reference for all voltage measurements; this internally fused pin is at ground potential."       },       {         "number": "6",         "name": "LOGIC SUPPLY (VCC)",         "type": "power_in",-        "description": "Logic supply input, operating range 4.5 V to 5.5 V (typically 5 V)."+        "description": "Logic supply voltage, operating range 4.5 V to 5.5 V, typically 5 V."       },       {         "number": "7",         "name": "PHASE",         "type": "input",-        "description": "Logic input that sets the direction of current flow in the load (Table 1), with an internal dead time of about 500 ns to prevent crossover current."+        "description": "Controls the direction of current flow in the load, with an internally generated dead time of approximately 500 ns to prevent crossover current when PHASE switches."       },       {         "number": "8",         "name": "D2 (DATA2)",         "type": "input",-        "description": "Most significant DAC data input selecting the output current ratio; logic-high requires VIN(1) ≥ 0.55 × VCC and logic-low requires VIN(0) ≤ 0.27 × VCC, and D0 to D2 all low turns off all outputs."+        "description": "Most significant of the three DAC control bits; logic high requires VCC × 0.55 minimum and logic low requires VCC × 0.27 maximum, and D0-D2 all low disables all outputs."       },       {         "number": "9",         "name": "D1 (DATA1)",         "type": "input",-        "description": "Middle DAC data input selecting the output current ratio; logic-high requires VIN(1) ≥ 0.55 × VCC and logic-low requires VIN(0) ≤ 0.27 × VCC."+        "description": "Middle control bit of the three-bit nonlinear DAC that sets the output current ratio; logic levels are VCC × 0.55 minimum for high and VCC × 0.27 maximum for low."       },       {         "number": "10",         "name": "OUTA",         "type": "output",-        "description": "One of two load output connections, rated for continuous output current to ±1.5 A and operating voltages to 50 V."+        "description": "One of two full-bridge output load connections, rated for continuous output current of ±1.5 A and an output voltage rating of 50 V."       },       {         "number": "11",         "name": "SENSE",         "type": "passive",-        "description": "Connection to the sink-transistor emitters where sense resistor RS is connected to ground; the absolute maximum sense voltage is 0.5 V."+        "description": "Connection to the sink-transistor emitters; the current-sense resistor RS is connected between this pin and ground."       },       {         "number": "12",         "name": "GROUND",         "type": "power_in",-        "description": "Return for the logic supply (VCC) and load supply (VBB) and the reference for all voltage measurements; internally fused pin at ground potential."+        "description": "Return for the logic supply (VCC) and load supply (VBB) and the reference for all voltage measurements; this internally fused pin is at ground potential."       },       {         "number": "13",         "name": "GROUND",         "type": "power_in",-        "description": "Return for the logic supply (VCC) and load supply (VBB) and the reference for all voltage measurements; internally fused pin at ground potential."+        "description": "Return for the logic supply (VCC) and load supply (VBB) and the reference for all voltage measurements; this internally fused pin is at ground potential."       },       {         "number": "14",         "name": "D0 (DATA0)",         "type": "input",-        "description": "Least significant DAC data input selecting the output current ratio; logic-high requires VIN(1) ≥ 0.55 × VCC and logic-low requires VIN(0) ≤ 0.27 × VCC."+        "description": "Least significant of the three DAC control bits; logic high requires VCC × 0.55 minimum and logic low requires VCC × 0.27 maximum."       },       {         "number": "15",         "name": "OUTB",         "type": "output",-        "description": "One of two load output connections, rated for continuous output current to ±1.5 A and operating voltages to 50 V."+        "description": "One of two full-bridge output load connections, rated for continuous output current of ±1.5 A and an output voltage rating of 50 V."       },       {         "number": "16",         "name": "LOAD SUPPLY (VBB)",         "type": "power_in",-        "description": "Load supply voltage input, operating range 5 V to 50 V."+        "description": "Supply voltage for the motor load, operating range 5 V to 50 V."       }     ],     "provenance": {@@ -156,11 +156,11 @@         "consensus": "agreed",         "guards": "pin_guards 0.1: passed",         "guard_notes": [-          "extractor flagged: Pin numbers and names were taken from the Terminal Functions table on page 5, which the datasheet sa; Pins 4, 5, 12 and 13 are marked as internally fused in the LB package drawing (page 12). They are li; The ERC types for RC (pin 3) and SENSE (pin 11) are not stated in the datasheet. They are classified"+          "extractor flagged: The page 9 pin-diagram text is scrambled, so pin assignments were taken from the Terminal Functions ; Pin types for PFD, REF, RC, SENSE and the bridge outputs are inferred from their functions in the da"         ],         "pages_sent": 13,-        "cost_usd": 0.0748,-        "at": "2026-11-10T18:40:06"+        "cost_usd": 0.0725,+        "at": "2026-11-11T00:38:24"       },       "datasheet": {         "url": "https://datasheet.lcsc.com/datasheet/pdf/e7f1b9e2417e49dda6c337bbb6e0b535.pdf",@@ -197,7 +197,7 @@         "centre_offset_mm": 0,         "footprint_binding": "identity",         "sha256": "159663ceb2b4996b1b89d3111e4a355fc27de3e24d3570f50e5ed9086e0d73af",-        "checked": "2026-11-10",+        "checked": "2026-11-11",         "checked_by": "factory/step_pose.py (Z-up, origin, seat, binding)"       },       {@@ -215,8 +215,8 @@         "zmin_mm": 0,         "centre_offset_mm": 0,         "footprint_binding": "identity",-        "sha256": "cec4a54e1c302a0631fc22fa775fe87cfea111274b23382463723c250059f829",-        "checked": "2026-11-10",+        "sha256": "aa78a388270ed8f0096bc3990660e0b4aac736147ea7447a0a9deeaccb23d615",+        "checked": "2026-11-11",         "checked_by": "factory/step_pose.py (Z-up, origin, seat, binding)"       }     ],@@ -226,22 +226,22 @@       "D": {         "nom_mm": 10.3,         "range_mm": [-          null,-          null+          10.1,+          10.5         ]       },       "E1": {         "nom_mm": 7.5,         "range_mm": [-          null,-          null+          7.4,+          7.6         ]       },       "E": {         "nom_mm": 10.3,         "range_mm": [-          null,-          null+          9.97,+          10.63         ]       },       "e": {@@ -723,5 +723,7 @@   ],   "visibility": {     "public": true-  }+  },+  "description": "Allegro MicroSystems, LLC Motor Driver ICs, SOIC-16-300mil. Pinout cross-checked by two models against the datasheet, KiCad symbol/footprint/3D.",+  "org": "adom" }\ No newline at end of file