# A1308LLHLT-1-T

**Allegro MicroSystems, LLC** · Hall Sensor · SOT-23W

A1308LLHLT-1-T from Allegro MicroSystems, LLC, in a SOT-23W. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.

## Pinout

| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | VCC | power_in | Input power supply (4.5 to 5.5 V operating, 8 V absolute maximum); tie to GND with a bypass capacitor (0.1 µF used in the characteristics). |
| 2 | VOUT | output | Analog ratiometric output signal proportional to the applied magnetic field, with a quiescent output of about 2.5 V at VCC = 5 V; requires a load of at least 4.7 kΩ to GND and at most 10 nF. |
| 3 | GND | power_in | Ground. |

## Key specifications

| Parameter | Value |
|---|---|
| Manufacturer | Allegro MicroSystems, LLC |
| Package | SOT-23W |
| Category | Sensors |
| Pins | 3 |

## Electrical characteristics

Limits as printed in the datasheet (page.json `metadata.characteristics` carries them as data).

| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Supply Voltage | VCC | 4.5 | 5 | 5.5 | V |  | 4 |
| Undervoltage Threshold (power on) | VUVLOHI |  |  | 3 | V | L temp. option tested at TA = 25°C to 150°C (device powers on) | 4 |
| Undervoltage Threshold (power off) | VUVLOLO | 2.5 |  |  | V | L temp. option tested at TA = 25°C to 150°C (device powers off) | 4 |
| Supply Current | ICC |  | 9 | 11.5 | mA | No load on VOUT | 4 |
| VCC Ramp Time | tVCC | 0.005 |  | 100 | ms | TA = 25°C | 4 |
| VCC Off Level | VCCOFF | 0 |  | 0.55 | V | TA = 25°C | 4 |
| Supply Zener Clamp Voltage | VZ | 6 | 7.3 |  | V | TA = 25°C, ICC = 14.5 mA | 4 |
| Output Load Resistance | RL | 4.7 |  |  | kΩ | VOUT to GND | 4 |
| Output Load Capacitance | CL |  |  | 10 | nF | VOUT to GND | 4 |
| Output Voltage Clamp High | VCLPHIGH | 4.35 | 4.5 | 4.65 | V | TA = 25°C, RL=10kΩ(VOUT to GND) | 4 |
| Output Voltage Clamp Low | VCLPLOW | 0.4 | 0.55 | 0.7 | V | TA = 25°C, RL=10kΩ(VOUTto VCC) | 4 |
| Sensitivity (A1308LLHLX-1-T) | Sens | 1.17 | 1.3 | 1.43 | mV/G | TA = 25°C | 4 |
| Quiescent Voltage Output | VOUT(Q) | 2.488 | 2.5 | 2.512 | V | TA = 25°C | 5 |
| Sensitivity Temperature Coefficient | TCSens | 0.08 | 0.12 | 0.16 | %/°C | Programmed at TA = 150°C (L temp. option), calculated relative to Sens at 25°C | 5 |
| Typical Quiescent Voltage Output Drift Across Temperature Range (A1308LLHLX-1-T) | ΔVOUT(Q) | -15 | 0 | 15 | mV | TA = 150°C | 5 |
| Forward Supply Voltage | VCC |  |  | 8 | V |  | 2 |
| Reverse Supply Voltage | VRCC | -0.1 |  |  | V |  | 2 |
| Forward Output Voltage | VOUT |  |  | 7 | V |  | 2 |
| Reverse Output Voltage | VROUT | -0.1 |  |  | V |  | 2 |
| Output Source Current | IOUT(SOURCE) |  |  | 2 | mA | VOUT to GND | 2 |
| Output Sink Current | IOUT(SINK) |  |  | 10 | mA | VCC to VOUT | 2 |
| Operating Ambient Temperature (Range L) | TA | -40 |  | 150 | °C | Range L | 2 |
| Maximum Junction Temperature | TJ(max) |  |  | 165 | °C |  | 2 |
| Storage Temperature | Tstg | -65 |  | 170 | °C |  | 2 |
| Package Thermal Resistance, 1-layer PCB | RθJA |  | 228 |  | °C/W | Package LH, 1-layer PCB with copper limited to solder pads | 3 |
| Package Thermal Resistance, 2-layer PCB | RθJA |  | 110 |  | °C/W | Package LH, 2-layer PCB with 0.463 in.2 of copper area each side connected by thermal vias | 3 |
| Power-On Time | tPO |  | 50 |  | µs | TA = 25°C, CL(PROBE) = 10 pF | 4 |
| Delay to Clamp | tCLP |  | 30 |  | µs | TA = 25°C, CL = 10 nF | 4 |
| Internal Bandwidth | BWi |  | 20 |  | kHz | Small signal -3 dB | 4 |
| Chopping Frequency | fC |  | 400 |  | kHz | TA = 25°C | 4 |
| Output Referred Noise | VN |  | 1.7 |  | G | VCC = 5 V, TA = 25°C, CBYPASS = open, Sens ≥ 1.3 mV/G, no load on VOUT | 4 |
| Input Referred RMS Noise Density | VNRMS |  | 1.5 |  | mG/√Hz | VCC = 5 V, TA = 25°C, CBYPASS = open, Sens ≥ 1.3 mV/G, no load on VOUT | 4 |
| DC Output Resistance | ROUT |  | 3 |  | Ω |  | 4 |
| Linearity Sensitivity Error | LinERR |  | 1.5 |  | % | printed as ±1.5 | 5 |
| Symmetry Sensitivity Error | SymERR |  | 1.5 |  | % | printed as ±1.5 | 5 |
| Ratiometry Quiescent Voltage Output Error | RatVOUT(Q) |  | 1.5 |  | % | Across supply voltage range (relative to VCC = 5 V); printed as ±1.5 | 5 |
| Ratiometry Sensitivity Error | RatSens |  | 1.5 |  | % | Across supply voltage range (relative to VCC = 5 V); printed as ±1.5 | 5 |
| Ratiometry Clamp Error | RatVOUTCLP |  | 1.5 |  | % | TA = 25°C, across supply voltage range (relative to VCC = 5 V); printed as ±1.5 | 5 |
| Sensitivity Drift Due to Package Hysteresis | ΔSensPKG |  | 2 |  | % | TA = 25°C, after temperature cycling; printed as ±2 | 5 |

## Materials and finish

As the datasheet states them (page.json `metadata.appearance`; the 3D model's colours follow it).

| Part | Material | Colour / plating | Datasheet says | Page |
|---|---|---|---|---|
| contacts |  | tin | lead (Pb) free, with 100% matte-tin leadframe plating. Linear Hall-Effect Sensor ICs with Analog Output | 2 |

## CAD (KiCad official)

- Symbol: `A1308LLHLT-1-T`
- Footprint: `Package_TO_SOT_SMD:SOT-23`
- 3D model: SOT-23W (KiCad packages3D, STEP)
- 3D model files: `a1308llhlt-1-t-etched.step` / `a1308llhlt-1-t-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `a1308llhlt-1-t.step` / `a1308llhlt-1-t.glb` are the bare package body.

## Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

- **Datasheet:** [Allegro MicroSystems, LLC datasheet](docs/a1308llhlt-1-t-datasheet.pdf) (12 pp, sha256 `41702bf15fb171d6`, retrieved 2026-10-23, tier: lcsc)
- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.3`, primary `claude-sonnet-5-5` (text), consensus `claude-sonnet-5-5` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
- **CAD:** KiCad official libraries (CC-BY-SA 4.0).

[Datasheet PDF](docs/a1308llhlt-1-t-datasheet.pdf)