main
Ray
Publish 0.1.1
f14e18c
74HC595MT
HGSEMI · Shift Registers · TSSOP-16
74HC595MT from HGSEMI, in a TSSOP-16. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | QB | tri_state | Parallel data output bit B of the 8-bit storage register, which goes high impedance when OE is high. |
| 2 | QC | tri_state | Parallel data output bit C of the 8-bit storage register, which goes high impedance when OE is high. |
| 3 | QD | tri_state | Parallel data output bit D of the 8-bit storage register, which goes high impedance when OE is high. |
| 4 | QE | tri_state | Parallel data output bit E of the 8-bit storage register, which goes high impedance when OE is high. |
| 5 | QF | tri_state | Parallel data output bit F of the 8-bit storage register, which goes high impedance when OE is high. |
| 6 | QG | tri_state | Parallel data output bit G of the 8-bit storage register, which goes high impedance when OE is high. |
| 7 | QH | tri_state | Parallel data output bit H of the 8-bit storage register, which goes high impedance when OE is high. |
| 8 | GND | power_in | Power ground of the device. |
| 9 | Q'H | output | Serial data output that carries the shift register's last bit (Qn-1) for cascading multiple devices. |
| 10 | ~{SCLR} | input | Shift register clear input; a low level clears the shift register so that Q'H goes to 0. |
| 11 | SCK | input | Shift register clock input that shifts data on its rising edge, with a maximum frequency of 10 MHz and a minimum pulse width of 20 ns. |
| 12 | RCK | input | Storage (output latch) register clock input that transfers the shift register contents to the parallel outputs on its rising edge. |
| 13 | ~{G} | input | Output enable input; a high level places outputs QA to QH in high impedance and a low level enables them. |
| 14 | SER | input | Serial data input to the shift register, requiring 20 ns setup and 5 ns hold relative to SCK. |
| 15 | QA | tri_state | Parallel data output bit A of the 8-bit storage register, which goes high impedance when OE is high. |
| 16 | VCC | power_in | Positive supply pin; the datasheet specifies an operating supply of 3.2 V to 6 V (5 V typical) and an absolute maximum of -0.5 V to 6.5 V. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | HGSEMI |
| Package | TSSOP-16 |
| Category | Logic |
| Pins | 16 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Supply voltage VCC (absolute maximum: working voltage) | VCC | -0.5 | 6.5 | V | 4 | ||
| Input/output voltage VIN, VOUT (absolute maximum) | VIN, VOUT | -0.5 | V | 4 | |||
| Input/output clamp current | IIK, IOK | -20 | 20 | mA | 4 | ||
| Output current | IOUT | -35 | 35 | mA | 4 | ||
| VCC, GND current | ICC, IGND | -70 | 70 | mA | 4 | ||
| Power dissipation | PD | 500 | mW | 4 | |||
| Operating temperature (listed in absolute maximum table) | TA | -40 | 85 | ℃ | 4 | ||
| Storage temperature | TS | -65 | 150 | ℃ | 4 | ||
| Lead soldering temperature | TW | 260 | ℃ | 10s | 4 | ||
| Supply voltage VCC (recommended operating) | VCC | 3.2 | 5 | 6 | V | 5 | |
| Input/output voltage VIN, VOUT (recommended operating) | VIN, Vout | 0 | V | 5 | |||
| Input rise/fall time | tr tf | 0 | 1000 | ns | VCC=2.0V | 5 | |
| Input rise/fall time | tr tf | 0 | 500 | ns | VCC=4.5V | 5 | |
| Input rise/fall time | tr tf | 0 | 400 | ns | VCC=6.0V | 5 | |
| High-level input voltage VIH | VIH | 3.15 | V | VCC=4.5V; TA=25℃ | 5 | ||
| High-level input voltage VIH | VIH | 4.2 | V | VCC=6.0V; TA=25℃ | 5 | ||
| Low-level input voltage VIL | VIL | 1.35 | V | VCC=4.5V; TA=25℃ | 5 | ||
| Low-level input voltage VIL | VIL | 1.8 | V | VCC=6.0V; TA=25℃ | 5 | ||
| High-level output voltage QA to QH, Q′H | VOH | 4.4 | V | VI=VIH or VIL, IOH=20μA; VCC=4.5V; TA=25℃ | 5 | ||
| High-level output voltage QA to QH, Q′H | VOH | 5.9 | V | VI=VIH or VIL, IOH=20μA; VCC=6.0V; TA=25℃ | 5 | ||
| High-level output voltage QA to QH | VOH | 3.9 | 4.3 | V | IOH=6.0mA; VCC=4.5V; TA=25℃ | 5 | |
| High-level output voltage QA to QH | VOH | 5.2 | 5.8 | V | IOH=7.8mA; VCC=6.0V; TA=25℃ | 5 | |
| High-level output voltage Q′H | VOH | 3.9 | 4.2 | V | IOH=4.0mA; VCC=4.5V; TA=25℃ | 5 | |
| High-level output voltage Q′H | VOH | 5.2 | 5.7 | V | IOH=5.2mA; VCC=6.0V; TA=25℃ | 5 | |
| Low-level output voltage QA to QH, Q′H | VOL | 0.1 | V | VI=VIH or VIL, IOH=20μA; VCC=4.5V; TA=25℃ | 5 | ||
| Low-level output voltage QA to QH | VOL | 0.2 | 0.4 | V | IOH=6.0mA; VCC=4.5V; TA=25℃ | 5 | |
| Low-level output voltage QA to QH | VOL | 0.25 | 0.4 | V | IOH=7.8mA; VCC=6.0V; TA=25℃ | 5 | |
| Low-level output voltage Q′H | VOL | 0.2 | 0.5 | V | IOH=4.0mA; VCC=4.5V; TA=25℃ | 5 | |
| Low-level output voltage Q′H | VOL | 0.15 | 0.5 | V | IOH=5.2mA; VCC=6.0V; TA=25℃ | 5 | |
| Off-state output current | IOZ | 10 | μA | VOUT=VCC or GND, VI=VIH or VIL; VCC=6.0V; TA=25℃ | 5 | ||
| Input current | IIN | 1 | μA | VI=VCC or GND; VCC=6.0V; TA=25℃ | 5 | ||
| Operating (quiescent) supply current | ICC | 5 | μA | VI=VCC or GND, IOUT=0μA; VCC=6.0V; TA=25℃ | 5 | ||
| Operating voltage VCC | VCC | 3.2 | 6 | V | TA=25℃ | 5 | |
| Maximum SCK clock frequency | fMax | 10 | MHz | Ta=25℃, VCC=5.0V, tr=tf≤20ns | 6 | ||
| Propagation delay SCK to Q′H | tPHL, tPLH | 100 | ns | CL=50pF; Ta=25℃, VCC=5.0V | 6 | ||
| Propagation delay RCK to QA thru QH | tPHL, tPLH | 100 | ns | CL=50pF; Ta=25℃, VCC=5.0V | 6 | ||
| Propagation delay SCLR (glyph unreadable in source) to QA thru QH | tPHL, tPLH | 50 | ns | CL=50pF; Ta=25℃, VCC=5.0V | 6 | ||
| Output enable time OE to QA thru QH | tZH, tZL | 17 | ns | RL=1kΩ CL=50pF; Ta=25℃, VCC=5.0V | 6 | ||
| Output disable time OE to QA thru QH | tHZ, tLZ | 15 | ns | RL=1kΩ CL=50pF; Ta=25℃, VCC=5.0V | 6 | ||
| Minimum setup (storage) time SER to SCK | tSU | 20 | ns | Ta=25℃, VCC=5.0V, tr=tf≤20ns | 6 | ||
| Minimum setup (storage) time SCK to RCK | tSU | 20 | ns | Ta=25℃, VCC=5.0V, tr=tf≤20ns | 6 | ||
| Minimum clear time SCLR to SCK | Trem | 10 | ns | Ta=25℃, VCC=5.0V, tr=tf≤20ns | 6 | ||
| Minimum pulse width SCK or (glyph unreadable in source) | tW | 20 | ns | Ta=25℃, VCC=5.0V, tr=tf≤20ns | 6 | ||
| Minimum hold time SER to SCK | tH | 5 | ns | Ta=25℃, VCC=5.0V, tr=tf≤20ns | 6 | ||
| Output rise/fall time QA thru QH, Q′H | tTLH, tTHL | 100 | ns | Ta=25℃, VCC=5.0V, tr=tf≤20ns | 6 |
CAD (KiCad official)
- Symbol:
74HC595MT - Footprint:
Package_SO:TSSOP-16_4.4x5mm_P0.65mm - 3D model: TSSOP-16, generated from the KiCad footprint (body from the F.Fab outline, terminals on the pads, 0.9 mm nominal TSSOP height). Neither the vendor nor KiCad ships a 3D model for this package, so the dimensions are nominal, not the manufacturer's CAD (STEP)
- 3D model files:
74hc595mt-etched.step/74hc595mt-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);74hc595mt.step/74hc595mt.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: HGSEMI datasheet (13 pp, sha256
2466d95b2f765594, retrieved 2026-11-09, tier: manufacturer) - Datasheet language: Chinese. Pin names, descriptions, and specs on this page were extracted and translated to English by ds2sf; the linked PDF is the manufacturer original.
- Extractor:
ds2sf(Claude). Every pin and dimension is cited to a datasheet page; it refuses to fabricate. - CAD: KiCad official libraries (CC-BY-SA 4.0).
# 74HC595MT
**HGSEMI** · Shift Registers · TSSOP-16
74HC595MT from HGSEMI, in a TSSOP-16. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
## Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | QB | tri_state | Parallel data output bit B of the 8-bit storage register, which goes high impedance when OE is high. |
| 2 | QC | tri_state | Parallel data output bit C of the 8-bit storage register, which goes high impedance when OE is high. |
| 3 | QD | tri_state | Parallel data output bit D of the 8-bit storage register, which goes high impedance when OE is high. |
| 4 | QE | tri_state | Parallel data output bit E of the 8-bit storage register, which goes high impedance when OE is high. |
| 5 | QF | tri_state | Parallel data output bit F of the 8-bit storage register, which goes high impedance when OE is high. |
| 6 | QG | tri_state | Parallel data output bit G of the 8-bit storage register, which goes high impedance when OE is high. |
| 7 | QH | tri_state | Parallel data output bit H of the 8-bit storage register, which goes high impedance when OE is high. |
| 8 | GND | power_in | Power ground of the device. |
| 9 | Q'H | output | Serial data output that carries the shift register's last bit (Qn-1) for cascading multiple devices. |
| 10 | ~{SCLR} | input | Shift register clear input; a low level clears the shift register so that Q'H goes to 0. |
| 11 | SCK | input | Shift register clock input that shifts data on its rising edge, with a maximum frequency of 10 MHz and a minimum pulse width of 20 ns. |
| 12 | RCK | input | Storage (output latch) register clock input that transfers the shift register contents to the parallel outputs on its rising edge. |
| 13 | ~{G} | input | Output enable input; a high level places outputs QA to QH in high impedance and a low level enables them. |
| 14 | SER | input | Serial data input to the shift register, requiring 20 ns setup and 5 ns hold relative to SCK. |
| 15 | QA | tri_state | Parallel data output bit A of the 8-bit storage register, which goes high impedance when OE is high. |
| 16 | VCC | power_in | Positive supply pin; the datasheet specifies an operating supply of 3.2 V to 6 V (5 V typical) and an absolute maximum of -0.5 V to 6.5 V. |
## Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | HGSEMI |
| Package | TSSOP-16 |
| Category | Logic |
| Pins | 16 |
## Electrical characteristics
Limits as printed in the datasheet (page.json `metadata.characteristics` carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Supply voltage VCC (absolute maximum: working voltage) | VCC | -0.5 | | 6.5 | V | | 4 |
| Input/output voltage VIN, VOUT (absolute maximum) | VIN, VOUT | -0.5 | | | V | | 4 |
| Input/output clamp current | IIK, IOK | -20 | | 20 | mA | | 4 |
| Output current | IOUT | -35 | | 35 | mA | | 4 |
| VCC, GND current | ICC, IGND | -70 | | 70 | mA | | 4 |
| Power dissipation | PD | | | 500 | mW | | 4 |
| Operating temperature (listed in absolute maximum table) | TA | -40 | | 85 | ℃ | | 4 |
| Storage temperature | TS | -65 | | 150 | ℃ | | 4 |
| Lead soldering temperature | TW | | | 260 | ℃ | 10s | 4 |
| Supply voltage VCC (recommended operating) | VCC | 3.2 | 5 | 6 | V | | 5 |
| Input/output voltage VIN, VOUT (recommended operating) | VIN, Vout | 0 | | | V | | 5 |
| Input rise/fall time | tr tf | 0 | | 1000 | ns | VCC=2.0V | 5 |
| Input rise/fall time | tr tf | 0 | | 500 | ns | VCC=4.5V | 5 |
| Input rise/fall time | tr tf | 0 | | 400 | ns | VCC=6.0V | 5 |
| High-level input voltage VIH | VIH | 3.15 | | | V | VCC=4.5V; TA=25℃ | 5 |
| High-level input voltage VIH | VIH | 4.2 | | | V | VCC=6.0V; TA=25℃ | 5 |
| Low-level input voltage VIL | VIL | | | 1.35 | V | VCC=4.5V; TA=25℃ | 5 |
| Low-level input voltage VIL | VIL | | | 1.8 | V | VCC=6.0V; TA=25℃ | 5 |
| High-level output voltage QA to QH, Q′H | VOH | 4.4 | | | V | VI=VIH or VIL, IOH=20μA; VCC=4.5V; TA=25℃ | 5 |
| High-level output voltage QA to QH, Q′H | VOH | 5.9 | | | V | VI=VIH or VIL, IOH=20μA; VCC=6.0V; TA=25℃ | 5 |
| High-level output voltage QA to QH | VOH | 3.9 | 4.3 | | V | IOH=6.0mA; VCC=4.5V; TA=25℃ | 5 |
| High-level output voltage QA to QH | VOH | 5.2 | 5.8 | | V | IOH=7.8mA; VCC=6.0V; TA=25℃ | 5 |
| High-level output voltage Q′H | VOH | 3.9 | 4.2 | | V | IOH=4.0mA; VCC=4.5V; TA=25℃ | 5 |
| High-level output voltage Q′H | VOH | 5.2 | 5.7 | | V | IOH=5.2mA; VCC=6.0V; TA=25℃ | 5 |
| Low-level output voltage QA to QH, Q′H | VOL | | | 0.1 | V | VI=VIH or VIL, IOH=20μA; VCC=4.5V; TA=25℃ | 5 |
| Low-level output voltage QA to QH | VOL | | 0.2 | 0.4 | V | IOH=6.0mA; VCC=4.5V; TA=25℃ | 5 |
| Low-level output voltage QA to QH | VOL | | 0.25 | 0.4 | V | IOH=7.8mA; VCC=6.0V; TA=25℃ | 5 |
| Low-level output voltage Q′H | VOL | | 0.2 | 0.5 | V | IOH=4.0mA; VCC=4.5V; TA=25℃ | 5 |
| Low-level output voltage Q′H | VOL | | 0.15 | 0.5 | V | IOH=5.2mA; VCC=6.0V; TA=25℃ | 5 |
| Off-state output current | IOZ | | | 10 | μA | VOUT=VCC or GND, VI=VIH or VIL; VCC=6.0V; TA=25℃ | 5 |
| Input current | IIN | | | 1 | μA | VI=VCC or GND; VCC=6.0V; TA=25℃ | 5 |
| Operating (quiescent) supply current | ICC | | | 5 | μA | VI=VCC or GND, IOUT=0μA; VCC=6.0V; TA=25℃ | 5 |
| Operating voltage VCC | VCC | 3.2 | | 6 | V | TA=25℃ | 5 |
| Maximum SCK clock frequency | fMax | 10 | | | MHz | Ta=25℃, VCC=5.0V, tr=tf≤20ns | 6 |
| Propagation delay SCK to Q′H | tPHL, tPLH | | | 100 | ns | CL=50pF; Ta=25℃, VCC=5.0V | 6 |
| Propagation delay RCK to QA thru QH | tPHL, tPLH | | | 100 | ns | CL=50pF; Ta=25℃, VCC=5.0V | 6 |
| Propagation delay SCLR (glyph unreadable in source) to QA thru QH | tPHL, tPLH | | | 50 | ns | CL=50pF; Ta=25℃, VCC=5.0V | 6 |
| Output enable time OE to QA thru QH | tZH, tZL | | | 17 | ns | RL=1kΩ CL=50pF; Ta=25℃, VCC=5.0V | 6 |
| Output disable time OE to QA thru QH | tHZ, tLZ | | | 15 | ns | RL=1kΩ CL=50pF; Ta=25℃, VCC=5.0V | 6 |
| Minimum setup (storage) time SER to SCK | tSU | 20 | | | ns | Ta=25℃, VCC=5.0V, tr=tf≤20ns | 6 |
| Minimum setup (storage) time SCK to RCK | tSU | 20 | | | ns | Ta=25℃, VCC=5.0V, tr=tf≤20ns | 6 |
| Minimum clear time SCLR to SCK | Trem | 10 | | | ns | Ta=25℃, VCC=5.0V, tr=tf≤20ns | 6 |
| Minimum pulse width SCK or (glyph unreadable in source) | tW | 20 | | | ns | Ta=25℃, VCC=5.0V, tr=tf≤20ns | 6 |
| Minimum hold time SER to SCK | tH | 5 | | | ns | Ta=25℃, VCC=5.0V, tr=tf≤20ns | 6 |
| Output rise/fall time QA thru QH, Q′H | tTLH, tTHL | | | 100 | ns | Ta=25℃, VCC=5.0V, tr=tf≤20ns | 6 |
## CAD (KiCad official)
- Symbol: `74HC595MT`
- Footprint: `Package_SO:TSSOP-16_4.4x5mm_P0.65mm`
- 3D model: TSSOP-16, generated from the KiCad footprint (body from the F.Fab outline, terminals on the pads, 0.9 mm nominal TSSOP height). Neither the vendor nor KiCad ships a 3D model for this package, so the dimensions are nominal, not the manufacturer's CAD (STEP)
- 3D model files: `74hc595mt-etched.step` / `74hc595mt-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `74hc595mt.step` / `74hc595mt.glb` are the bare package body.
## Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- **Datasheet:** [HGSEMI datasheet](docs/74hc595mt-datasheet.pdf) (13 pp, sha256 `2466d95b2f765594`, retrieved 2026-11-09, tier: manufacturer)
- **Datasheet language:** Chinese. Pin names, descriptions, and specs on this page were extracted and translated to English by ds2sf; the linked PDF is the manufacturer original.
- **Extractor:** `ds2sf` (Claude). Every pin and dimension is cited to a datasheet page; it refuses to fabricate.
- **CAD:** KiCad official libraries (CC-BY-SA 4.0).
[Datasheet PDF](docs/74hc595mt-datasheet.pdf)