Loads when you scroll to it. Unloads after 5 minutes in the background.

Symbol & Footprint

Schematic Symbol

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.

PCB Footprint

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Loads when you scroll to it. Unloads after 5 minutes in the background.
Download PDF
Contents

README

markdown

65HVD75EIM

HGSEMI · RS-485/RS-422 ICs · SOIC-8

65HVD75EIM from HGSEMI, in a SOIC-8. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model). Symbol and footprint from KiCad-official CAD; the 3D model is generated from the datasheet's package dimensions.

Pinout

Pin Name Type Function
1 RO output Receiver output: with RE low, RO is high when A−B is at or above the receiver threshold and low when A−B is at or below −200 mV (function table and failsafe section give the threshold as −50 mV).
2 RE input Receiver output enable, active low: RO is active when RE is low and high-impedance when RE is high; RE high with DE low puts the device into low-power shutdown; this pin uses a hot-plug input structure.
3 DE input Driver output enable: the driver output is active when DE is high and high-impedance when DE is low; DE low with RE high puts the device into low-power shutdown; this pin uses a hot-plug input structure.
4 DI input Driver input: with DE high, a low on DI drives A low and B high, and a high on DI drives A high and B low.
5 GND power_in Ground reference for the device.
6 A bidirectional Receiver non-inverting input and driver non-inverting output on the RS-485/RS-422 bus; the bus common-mode range is −7 V to +12 V.
7 B bidirectional Receiver inverting input and driver inverting output on the RS-485/RS-422 bus; the bus common-mode range is −7 V to +12 V.
8 VCC power_in Positive supply: 3.15 V ≤ VCC ≤ 3.45 V; decouple with a 0.1 µF capacitor to ground.

Key specifications

Parameter Value
Manufacturer HGSEMI
Package SOIC-8
Category Interface ICs
Pins 8

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
Supply voltage VCC 3.15 3.45 V 3
Differential driver output voltage, RL=100 ohm (RS-422) VOD 2 V Fig 1, RL=100 ohm; max printed as VCC 3
Differential driver output voltage, RL=54 ohm (RS-485) VOD 1.5 V Fig 1, RL=54 ohm; max printed as VCC 3
Change in magnitude of differential driver output voltage dVOD 0.2 V Fig 1, RL=100 ohm or RL=54 ohm 3
Driver common-mode output voltage VOC 3 V Fig 1, RL=100 ohm or RL=54 ohm; min printed as VCC/2 3
Change in magnitude of common-mode output voltage dVOC 0.2 V Fig 1, RL=100 ohm or RL=54 ohm 3
Input high voltage VIH 2 V DE, DI inputs 4
Input low voltage VIL 0.8 V DE, DI inputs 4
Input current IIN -1 1 uA DE, DI inputs 4
Input current (A,B) full duplex IA, IB 125 uA DE=GND, VCC=GND or VCC, VIN=12V 4
Input current (A,B) full duplex IA, IB -75 uA DE=GND, VCC=GND or VCC, VIN=-7V 4
Output leakage current (Y,Z) full duplex IO 125 uA DE=GND, VCC=GND or VCC, VIN=12V 4
Output leakage current (Y,Z) full duplex IO -100 uA DE=GND, VCC=GND or VCC, VIN=-7V 4
Driver short-circuit output current IOSD 250 mA 0 <= VOUT <= 12V 4
Driver short-circuit output current IOSD -250 mA -7 <= VOUT <= VCC 4
Driver short-circuit foldback output current IOSDF 20 mA VCC-1V <= VOUT <= VCC+0.5V 4
Driver short-circuit foldback output current IOSDF -20 mA -0.5V <= VOUT <= +1V 4
Receiver differential threshold voltage VTH -200 -125 -50 mV -7V <= VCM <= 12V 4
Receiver output low voltage VOL 0.4 V IO=4mA, VID=-200mV 4
Receiver tri-state output current IOZR -1 1 uA 0 <= VO <= VCC 4
Receiver output short-circuit current IOSR -95 95 mA 0V <= VRO <= VCC 4
Standby supply current ISHDN 0.05 10 uA DE=GND; second control pin = VCC (symbol garbled in source) 5
Supply current, no load ICC 400 900 uA No load; [control pin garbled]=VCC; DI=GND or VCC; DE=VCC 5
Supply current, no load ICC 330 600 uA No load; [control pin garbled]=VCC; DI=GND or VCC; DE=GND 5
Supply current, no load ICC 400 1000 uA No load; [control pin garbled]=GND; DI=GND or VCC; DE=VCC 5
Supply current, no load ICC 330 800 uA No load; [control pin garbled]=GND; DI=GND or VCC; DE=GND 5
IEC 61000-4-2 air-gap discharge on A,B pins -16 16 kV RS-485 pins A,B 5
IEC 61000-4-2 contact discharge (half duplex) on A,B pins -16 16 kV RS-485 pins A,B 5
HBM ESD pin to ground on A,B pins -16 16 kV RS-485 pins A,B 5
Operating temperature range (industrial, EI) -40 85 C 65HVDxxEI 3
Storage temperature -65 150 C 3
Lead temperature, soldering TLEAD 260 C 10 s soldering 3
Supply voltage VCC 6 V 3
Control input voltage RE, DE -0.3 6 V 3
Driver input voltage DI -0.3 6 V 3
Driver output voltage A,B -7 12 V 3
Receiver input voltage A,B -7 12 V 3
Receiver output voltage RO -0.3 V max printed as VCC+0.3 3
Continuous power dissipation 500 mW TA=+70C, 8-pin SOP 3
Driver propagation delay tDPLH, tDPHL 200 1000 ns Fig 2&5, RL=54 ohm, CL=50pF 7
Driver output skew tDSKEW -140 140 ns Fig 2&5, RL=54 ohm, CL=50pF 7
Driver rise and fall time tDR, tDF 250 900 ns Fig 2&5, RL=54 ohm, CL=50pF 7
Driver enable to output high tDZH 2500 ns Fig 3&6, CL=100pF, S3 closed 7
Driver enable to output low tDZL 2500 ns Fig 3&6, CL=100pF, S2 closed 7
Driver low to disable time tDLZ 100 ns Fig 3&6, CL=15pF, S2 closed 7
Driver high to disable time tDHZ 100 ns Fig 3&6, CL=15pF, S3 closed 7
Driver enable from standby to output high tDZH(SHDN) 5500 ns Fig 3&6, CL=15pF, S3 closed 7
Driver enable from standby to output low tDZL(SHDN) 5500 ns Fig 3&6, CL=15pF, S2 closed 7
Standby time (driver) tSHDN 50 700 ns Note 4 7
Receiver propagation delay tRPLH, tRPHL 200 ns Fig 7&8, CL=15pF, /VID/>=2.0V, VID<=15ns 7
Receiver output skew tRSKEW -30 30 ns Fig 7&8, CL=15pF, /VID/>=2.0V, VID<=15ns 7
Receiver enable to output low tRZL 50 ns Fig 4&9, S1=-1.5V, S2 to VCC 7
Receiver enable to output high tRZH 50 ns Fig 4&9, S1=+1.5V, S2 to GND 7
Receiver low to disable time tRLZ 50 ns Fig 4&9, S1=-1.5V, S2 to VCC 7
Receiver high to disable time tRHZ 50 ns Fig 4&9, S1=+1.5V, S2 to GND 7
Receiver enable from standby to output high tRZH(SHDN) 5500 ns Fig 4&9, S1=-1.5V, S2 to VCC 7
Receiver enable from standby to output low tRZL(SHDN) 5500 ns Fig 4&9, S1=+1.5V, S2 to GND 7
Standby time (receiver) tSHDN 50 700 ns Note 4 7

CAD (land: KiCad; 3D: generated from the datasheet)

  • Symbol: 65HVD75EIM
  • Footprint: Package_SO:SOIC-8_3.9x4.9mm_P1.27mm
  • 3D model: SOIC-8, generated on the KiCad land (body 3.9 x 5 mm, terminals on the pads, 1.4500000000000002 mm tall, datasheet A, midpoint of min and max). KiCad's stock model for this land is taller than the datasheet allows, so the model is generated from the datasheet drawing; the dimensions come from the datasheet drawing where it was read and are defaults otherwise (see provenance.model_3d_generated), not the manufacturer's CAD (STEP)
  • 3D model files: 65hvd75eim-etched.step / 65hvd75eim-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); 65hvd75eim.step / 65hvd75eim.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: HGSEMI datasheet (20 pp, sha256 11f027c743ac8483, retrieved 2026-11-17, tier: lcsc)
  • Datasheet language: Chinese. Pin names, descriptions, and specs on this page were extracted and translated to English by ds2sf; the linked PDF is the manufacturer original.
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-haiku-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: land: KiCad official libraries (CC-BY-SA 4.0); 3D: generated from the datasheet's package dimensions (provenance.model_3d_generated).

Datasheet PDF