main
Ray Publish 0.1.0 8fb48cd

2EDN8533RXTMA1

Infineon Technologies · Gate Drive ICs · MSOP-8-EP

2EDN8533RXTMA1 from Infineon Technologies, in a MSOP-8-EP. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 ENA input Enable input for channel A: if ENA is high or left open, OUTA follows INA, and a low ENA forces OUTA low.
2 INA input Logic input for channel A that controls OUTA, stated in the datasheet as non-inverting.
3 GND power_in Gate driver reference ground; the exposed pad of the PG-TSSOP-8 must be connected to this GND pin.
4 INB input Logic input for channel B that controls OUTB, stated in the datasheet as non-inverting.
5 OUTB output Low-impedance channel B driver output with source and sink capability.
6 VDD power_in Positive supply voltage with an operating range of 4.5 V/8.6 V to 20 V (the 4 V/8 V UVLO option applies).
7 OUTA output Low-impedance channel A driver output with source and sink capability.
8 ENB input Enable input for channel B: if ENB is high or left open, OUTB follows INB, and a low ENB forces OUTB low.
9 EP passive Exposed pad (from the footprint; not named in the datasheet pin table).

Key specifications

Parameter Value
Manufacturer Infineon Technologies
Package MSOP-8-EP
Category Power Supply Chip
Pins 9

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
Positive supply voltage VDD -0.3 22 V 13
Voltage at pins INA, INB, ENA, ENB VIN -12 22 V 13
Voltage at pins OUTA, OUTB VOUT -0.3 V VDD+0.3 V as printed; voltage spikes from reverse current peaks allowed 13
Voltage at pins OUTA, OUTB (repetitive pulse) VOUT -2 V Repetitive pulse < 200 ns; max printed as VDD+2 V 13
Reverse current peak at pins OUTA, OUTB ISNKREV / ISRCREV -5 5 A Apk < 500 ns 13
Junction temperature TJ -40 150 °C 13
Storage temperature TS -55 150 °C 13
ESD capability CDM VESD 0.5 kV Charged Device Model (CDM), JESD22-002 13
ESD capability HBM VESD 2 kV Human Body Model (HBM), JESD22-A114-B 13
Thermal resistance junction-ambient RthJA25 48 K/W PG-TSSOP-8, Tamb = 25°C 14
Thermal resistance junction-case (top) RthJP25 74 K/W PG-TSSOP-8, Tamb = 25°C 14
Thermal resistance junction-board RthJB25 22.5 K/W PG-TSSOP-8, Tamb = 25°C 14
Characterization parameter junction-top ΨthJC25 3 K/W PG-TSSOP-8, Tamb = 25°C 14
Characterization parameter junction-board ΨthJB25 21 K/W PG-TSSOP-8, Tamb = 25°C 14
Supply voltage VDD 4.5 20 V Min. defined by UVLO 15
Logic input voltage VIN -10 20 V 15
Junction temperature (operating) TJ -40 150 °C Continuous operation above 125°C may reduce life time 15
VDD quiescent current (OUT high) IVDDQU1 0.5 0.9 1.2 mA OUT = high, VDD = 12 V 15
VDD quiescent current (OUT low) IVDDQU2 0.3 0.5 0.7 mA OUT = low, VDD = 12 V 15
Undervoltage lockout turn on threshold (8 V) UVLOON 8 8.6 V 15
Undervoltage lockout turn off threshold (8 V) UVLOOFF 6.5 7 V 15
UVLO threshold hysteresis (8 V) UVLOHYS 0.8 1 1.2 V 15
Input voltage threshold for transition LH VINH 1.9 2.1 2.3 V 16
Input voltage threshold for transition HL VINL 1 1.2 1.4 V 16
Input pull up resistor RINH 400 kΩ Inputs with initial high logic level 16
Input pull down resistor RINL 100 kΩ Inputs with initial low logic level 16
High level (sourcing) output resistance RONSRC 0.4 0.8 1.4 Ω ISRC = 50 mA 16
High level (sourcing) output current ISRCPEAK 5 A Parameter not subject to production test - verified by design/characterization 16
Low level (sinking) output resistance RONSNK 0.35 0.6 1.2 Ω ISNK = 50 mA 16
Low level (sinking) output current ISNKPEAK -5 A Parameter not subject to production test - verified by design/characterization 16
Input/Enable to output propagation delay low to high tPDlh 15 19 25 ns CLOAD = 1.8 nF, VDD = 12 V; low to high transition at Input/Enable 17
Input/Enable to output propagation delay high to low tPDhl 15 19 25 ns CLOAD = 1.8 nF, VDD = 12 V; high to low transition at Input/Enable 17
Input/Enable to output propagation delay mismatch between the two channels ΔtPD 2 ns 17
Rise time tRISE 8.6 15 ns CLOAD = 1.8 nF, VDD = 12 V; not subject to production test - verified by component verification 17
Fall time tFALL 6 13 ns CLOAD = 1.8 nF, VDD = 12 V 17
Minimum input pulse width that changes output state tPW 6 10 ns CLOAD = 1.8 nF, VDD = 12 V; not subject to production test 17
VDD start-up time from UVLOON to OUTx tSTART 1.8 µs VDD rising to 12 V; see Figure 11 17
VDD deactivation time from UVLOOFF to OUTx tSTOP 500 ns VDD falling from 12 V; see Figure 11 17
Activation time of output clamping in UVLO condition tCLAMP,OUT 20 ns see Figure 13 17

CAD (KiCad official)

  • Symbol: 2EDN8533RXTMA1
  • Footprint: Package_SO:MSOP-8-1EP_3x3mm_P0.65mm_EP1.5x1.8mm
  • 3D model: MSOP-8-EP (KiCad packages3D, STEP)
  • 3D model files: 2edn8533rxtma1-etched.step / 2edn8533rxtma1-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); 2edn8533rxtma1.step / 2edn8533rxtma1.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: Infineon Technologies datasheet (36 pp, sha256 8f2442538a1422bf, retrieved 2026-11-02, tier: manufacturer)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-haiku-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF